CCU2 Menüs gehen nicht richtig auf

Einrichtung, Anschluss und Programmierung der HomeMatic CCU

Moderator: Co-Administratoren

Antworten
Granten
Beiträge: 37
Registriert: 18.12.2016, 16:35

CCU2 Menüs gehen nicht richtig auf

Beitrag von Granten » 19.01.2018, 18:44

Hallo Leute,

ich hoffe ihr könnt mir weiterhelfen. Meine CCU spint im Moment total.
Nach einem Neustart kam die Meldung "Die Homematic CCU2 ist noch nicht bereit". Danach erscheint wie gewohnt die Startseite und will alle Infos laden. An dieser Stelle blieb die CCU2 hängen und ist im Browser nicht mehr erreichbar. Per Ping aber weiterhin.
Das Problem habe ich durch einen Reset der CCU lösen können. Jetzt habe ich das Problem das viele Untermenüs wie z.B. Gerät anlernen oder Zernrale - Wartung einfach nicht aufgehen. Der Hintergrund der Seite wird Grau, mehr passiert aber nicht.
Ich habe es per Lan und per USB versucht. Beides ohne erfolg. Browser Cache geleert und auch anderen PC benutzt. Ohne erfolg.

Woran kann das liegen?


Eine Komponente der HomeMatic Zentrale reagiert nicht mehr.

Hierfür kann es eine Reihe von Ursachen geben:

es besteht keine Netzwerk-Verbindung
die Stromversorung der HomeMatic Zentrale wurde unterbrochen
mindestens eine Komponente der HomeMatic Zentrale ist abgestürzt

Überprüfen Sie die Netzwerk-Verbindung und die Stromversorgung der HomeMatic Zentrale. Starten Sie ggf. die HomeMatic Zentrale neu.
Nach oben
Benutzeravatar
anli
Beiträge: 4326
Registriert: 10.06.2009, 14:01
Wohnort: 20 Min. nördlich von Hannover und bei Bremen
Hat sich bedankt: 1 Mal
Danksagung erhalten: 23 Mal
Kontaktdaten:
Kontaktdaten von anli

Re: CCU2 Menüs gehen nicht richtig auf

Beitrag von anli » 19.01.2018, 23:04

Hallo,

beschreib bitte einmal Deine Zentrale genauer? Neue CCU2?

Lies bitte einmal viewtopic.php?f=31&t=41352 und schaue danach, wenn das Verhalten dem dort beschriebenen entspricht.

Die Ausgabe von

Code: Alles auswählen

ps -ef
auf der SSH-Konsole wenn der Fehler mit "eine Komponente ..." wäre auch interessant. Und das Log-File natürlich auch, das kannst Du hier in Code-Tags posten.

Wenn Du nicht weißt, was mit den einzelnen Dingen gemeint ist, frag noch einmal nach. Vieles findest du alternativ auch über google hier im Forum.
Herzliche Grüße, anli

Alle Angaben ohne Gewähr und Haftung meinerseits. Verwendung der von mir zur Verfügung gestellten Downloads auf eigene Gefahr. Ich bitte um Verständnis, dass ich aus zeitlichen Gründen keine unaufgeforderte Hilfestellung per PN/Mail geben kann. Bitte allgemeine Fragen ins Forum stellen, hier können viele fähige User viel schneller helfen.

Homematic-Manager v2: einfaches Tool zum Erstellen von Direktverknüpfungen und Bearbeiten von Gerätenamen, -parametern etc. für Homematic und HomematicIP (Alternative diesbzgl. zur WebUI)

Einsteiger-Hilfe • erweiterter Skript-Parser
Nach oben
Granten
Beiträge: 37
Registriert: 18.12.2016, 16:35

Re: CCU2 Menüs gehen nicht richtig auf

Beitrag von Granten » 20.01.2018, 11:54

anli hat geschrieben:Hallo,

beschreib bitte einmal Deine Zentrale genauer? Neue CCU2?
Ja es ist eine CCU2 auf Version 2.31.25

Hier die Meldungen die ich erhalten habe nachdem ich die Anleitung aus dem anderen Post befolgt habe. Die ersten zwei wiederholen sich andauernd ohne das ich was mache. das 3. kommt wenn ich auf Gerät anlernen drücke. es hat aber keinen Inhalt! Deswegen nur die URL

Code: Alles auswählen

{version: "1.1", result: [], error: null}
error
:
null
result
:
[]
version
:
"1.1"

Code: Alles auswählen

<script type="text/javascript">setTime("11:47");
setDate("20.01.2018");
if( $("presence") ) $("presence").innerHTML = "1";if( typeof(alarmLogSystem) == "object" ) alarmLogSystem.deleteAll();
setAlarmMessageCount(0);
if( typeof(serviceLogSystem) == "object" ) serviceLogSystem.deleteAll();
if (WebUI.HIDESTICKYUNREACH) {var svcCount = 0;var stickyCount = 0;var visibleSvcCount = svcCount - stickyCount;if(visibleSvcCount < 0) {visibleSvcCount = 0;}if( typeof(updateMessageView) == 'function' )updateMessageView(visibleSvcCount);setServiceMessageCount(visibleSvcCount);
} else {if( typeof(updateMessageView) == 'function' )updateMessageView(0);setServiceMessageCount(0);
 } if(urlParamInterfaces == "true") showRFInterfaces();// oUser: Admin
SwitchOffFlashLight();</script>

Code: Alles auswählen

http://192.168.0.251/config/cp_add_device.cgi?sid=@AiPvS6vdtM@
Hier die Ausgabe von ps -ef

Code: Alles auswählen

PID   USER     COMMAND
    1 root     init
    2 root     [kthreadd]
    3 root     [ksoftirqd/0]
    5 root     [kworker/u:0]
    6 root     [rcu_kthread]
    7 root     [khelper]
    8 root     [kdevtmpfs]
    9 root     [netns]
   10 root     [sync_supers]
   11 root     [bdi-default]
   12 root     [kintegrityd]
   13 root     [kblockd]
   14 root     [rpciod]
   15 root     [kworker/0:1]
   16 root     [kswapd0]
   17 root     [fsnotify_mark]
   18 root     [nfsiod]
   19 root     [crypto]
   24 root     [mtdblock0]
   25 root     [mtdblock1]
   26 root     [mtdblock2]
   27 root     [mtdblock3]
   28 root     [mtdblock4]
   29 root     [mtdblock5]
   30 root     [mtdblock6]
   31 root     [mtdblock7]
   32 root     [ubi_bgt0d]
   33 root     [ubi_bgt1d]
   34 root     [kworker/u:1]
   37 root     [deferwq]
   38 root     [devfreq_wq]
   43 root     [ubifs_bgt1_0]
   81 root     [eq3spi.0]
   88 root     [file-storage]
   91 root     [khubd]
  109 root     /usr/sbin/crond
  113 root     /sbin/syslogd -m 0
  115 root     /sbin/klogd
  118 root     /lib/udev/udevd -d
  128 root     watchdog -t 30 /dev/watchdog
  150 root     udhcpd -S /etc/udhcpd.usb0.conf
  154 root     /lib/udev/udevd -d
  155 root     /lib/udev/udevd -d
  259 root     udhcpc -x hostname homematic-ccu2 -V eQ3-CCU2 -b -s /bin/dhcp.script
  265 root     /usr/sbin/ifplugd -i eth0 -fI -u0 -d10
  281 root     [kworker/0:2]
  291 root     /bin/eq3configd
  292 root     /bin/ssdpd
  303 root     ntpclient -h ntp.homematic.com -l
  310 root     /usr/sbin/lighttpd -f /etc/lighttpd/lighttpd.conf
  317 root     /usr/sbin/sshd
  365 root     /bin/multimacd -f /etc/config/multimacd.conf -l 5
  387 root     /bin/rfd -f /etc/config/rfd.conf -l 5
  432 root     java -Xmx64m -Dlog4j.configuration=file:///etc/config/log4j.xml -Dfile.encoding=ISO-8859-1 -jar /opt/HMServer/HMIPServer.jar /etc/crRFD.conf
  467 root     /bin/tclsh /www/api/homematic.cgi
  591 root     /bin/ReGaHss.normal -f /etc/rega.conf -l 2
  594 root     /bin/hss_led
  613 root     /sbin/getty -L ttyAMA0 115200 vt100
  614 root     /sbin/getty -L ttyGS0 115200 vt100
  882 root     [flush-ubifs_1_0]
 1013 root     {sshd} sshd: root@pts/0
 1017 root     -sh
 1032 root     /bin/tclsh /www/api/homematic.cgi
 1036 root     /bin/tclsh /www/api/homematic.cgi
 1043 root     /bin/tclsh /www/config/cp_add_device.cgi
 1059 root     ps -ef
Ich hoffe du kannst damit was anfangen. Mir sagt das im Moment nichts
Nach oben
Benutzeravatar
anli
Beiträge: 4326
Registriert: 10.06.2009, 14:01
Wohnort: 20 Min. nördlich von Hannover und bei Bremen
Hat sich bedankt: 1 Mal
Danksagung erhalten: 23 Mal
Kontaktdaten:
Kontaktdaten von anli

Re: CCU2 Menüs gehen nicht richtig auf

Beitrag von anli » 20.01.2018, 16:39

Granten hat geschrieben:Hier die Ausgabe von ps -ef
Kannst Du das Fenster noch einmal größer ziehen bitte bevor Du den Befehl abschickst? Ich vermute, dass die Zeilen abgeschnitten sind.

Bitte auch noch einmal die Logs für Bidcos-RF und Logischicht auf "alles loggen" stellen, die CCU2 neu starten, dann die Dinge probieren und dann das Log hier posten (findest Du alles in der Systemsteuerung unter Zentralenwartung).
Herzliche Grüße, anli

Alle Angaben ohne Gewähr und Haftung meinerseits. Verwendung der von mir zur Verfügung gestellten Downloads auf eigene Gefahr. Ich bitte um Verständnis, dass ich aus zeitlichen Gründen keine unaufgeforderte Hilfestellung per PN/Mail geben kann. Bitte allgemeine Fragen ins Forum stellen, hier können viele fähige User viel schneller helfen.

Homematic-Manager v2: einfaches Tool zum Erstellen von Direktverknüpfungen und Bearbeiten von Gerätenamen, -parametern etc. für Homematic und HomematicIP (Alternative diesbzgl. zur WebUI)

Einsteiger-Hilfe • erweiterter Skript-Parser
Nach oben
Granten
Beiträge: 37
Registriert: 18.12.2016, 16:35

Re: CCU2 Menüs gehen nicht richtig auf

Beitrag von Granten » 21.01.2018, 11:07

anli hat geschrieben:
Granten hat geschrieben:Hier die Ausgabe von ps -ef
Kannst Du das Fenster noch einmal größer ziehen bitte bevor Du den Befehl abschickst? Ich vermute, dass die Zeilen abgeschnitten sind.
Nein das ist wirklich die gesammte Ausgabe von dem Befehl. Da fehlt nichts. Es fing bei init an und hört unten bei ps -ef auf.
anli hat geschrieben: Bitte auch noch einmal die Logs für Bidcos-RF und Logischicht auf "alles loggen" stellen, die CCU2 neu starten, dann die Dinge probieren und dann das Log hier posten (findest Du alles in der Systemsteuerung unter Zentralenwartung).
Würd ich gerne machen. Aber das ist eines der Menüs die ich eben nicht mehr auf bekomme. Wenn du mir einen anderen Weg sagen kannst mit dem ich das Umstellen kann mach ich das sofort.
Nach oben
Granten
Beiträge: 37
Registriert: 18.12.2016, 16:35

Re: CCU2 Menüs gehen nicht richtig auf

Beitrag von Granten » 21.01.2018, 14:03

OK. Ich konnte etwas erreichen. Ich habe jetzt die Firmware 2.29.23 eingespielt. Jetzt gehen alle Menüs wieder auf!

Neues Problem.

Jetzt stürzen am laufenden Band Module ab wie z.B. mit der Meldung "BidCos-RF Anlernmodus konnte nicht aktiviert werden."

Hier mal die Logdatei die ich jetzt erstellen konnte wie du es beschrieben hast:

Code: Alles auswählen

Jan 21 13:16:05 homematic-ccu2 syslog.info syslogd started: BusyBox v1.20.2
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: klogd started: BusyBox v1.20.2 (2017-10-11 14:29:35 CEST)
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.000000] Booting Linux on physical CPU 0
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.000000] Initializing cgroup subsys cpu
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    0.000000] Linux version 3.4.11.ccu2 (hudson@entw-build-10) (gcc version 4.6.1 (Sourcery CodeBench Lite 2011.09-70) ) #1 PREEMPT Wed Oct 11 14:58:54 CEST 2017
Jan 21 13:16:06 homematic-ccu2 user.warn kernel: [    0.000000] CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
Jan 21 13:16:06 homematic-ccu2 user.warn kernel: [    0.000000] CPU: VIVT data cache, VIVT instruction cache
Jan 21 13:16:06 homematic-ccu2 user.warn kernel: [    0.000000] Machine: eQ-3 HomeMatic CCU2
Jan 21 13:16:06 homematic-ccu2 user.warn kernel: [    0.000000] Memory policy: ECC disabled, Data cache writeback
Jan 21 13:16:06 homematic-ccu2 user.debug kernel: [    0.000000] On node 0 totalpages: 65536
Jan 21 13:16:06 homematic-ccu2 user.debug kernel: [    0.000000] free_area_init_node: node 0, pgdat c03c42ec, node_mem_map c03f8000
Jan 21 13:16:06 homematic-ccu2 user.debug kernel: [    0.000000]   Normal zone: 512 pages used for memmap
Jan 21 13:16:06 homematic-ccu2 user.debug kernel: [    0.000000]   Normal zone: 0 pages reserved
Jan 21 13:16:06 homematic-ccu2 user.debug kernel: [    0.000000]   Normal zone: 65024 pages, LIFO batch:15
Jan 21 13:16:06 homematic-ccu2 user.debug kernel: [    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Jan 21 13:16:06 homematic-ccu2 user.debug kernel: [    0.000000] pcpu-alloc: [0] 0 
Jan 21 13:16:06 homematic-ccu2 user.warn kernel: [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    0.000000] Kernel command line: eQ3Mode=production console=ttyAMA0,115200 ubi.mtd=7 ubi.mtd=6 ro ip=none root=ubi0:root ubi.mtd=7 rootfstype=ubifs noinitrd mtdparts=gpmi-nand:1024k(fcb)ro,1024k(bbt),1024k(bootenv),1536k(boo
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.000000] allocated 524288 bytes of page_cgroup
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.000000] Memory: 256MB = 256MB total
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    0.000000] Memory: 255276k/255276k available, 6868k reserved, 0K highmem
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    0.000000] Virtual kernel memory layout:
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    0.000000]     vmalloc : 0xd0800000 - 0xff000000   ( 744 MB)
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    0.000000]       .text : 0xc0008000 - 0xc037d000   (3540 kB)
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    0.000000]       .init : 0xc037d000 - 0xc039a000   ( 116 kB)
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    0.000000]       .data : 0xc039a000 - 0xc03c4a20   ( 171 kB)
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    0.000000]        .bss : 0xc03c4a44 - 0xc03f77dc   ( 204 kB)
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.000000] NR_IRQS:304
Jan 21 13:16:06 homematic-ccu2 user.err kernel: [    0.000000] saif0_clk_set_rate: clock is gated
Jan 21 13:16:06 homematic-ccu2 user.err kernel: [    0.000000] saif1_clk_set_rate: clock is gated
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.000000] Console: colour dummy device 80x30
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.000000] Calibrating delay loop... 226.09 BogoMIPS (lpj=1130496)
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.070000] pid_max: default: 32768 minimum: 301
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.070000] Mount-cache hash table entries: 512
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.070000] Initializing cgroup subsys cpuacct
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.070000] Initializing cgroup subsys memory
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.070000] Initializing cgroup subsys devices
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.070000] Initializing cgroup subsys freezer
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.070000] CPU: Testing write buffer coherency: ok
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.070000] Setting up static identity map for 0x402b1198 - 0x402b11f0
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.070000] devtmpfs: initialized
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.080000] dummy: 
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.080000] NET: Registered protocol family 16
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.080000] gpiochip_add: registered GPIOs 0 to 31 on device: gpio-mxs.0
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.080000] gpiochip_add: registered GPIOs 32 to 63 on device: gpio-mxs.1
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.080000] gpiochip_add: registered GPIOs 64 to 95 on device: gpio-mxs.2
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.080000] gpiochip_add: registered GPIOs 96 to 127 on device: gpio-mxs.3
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.080000] gpiochip_add: registered GPIOs 128 to 159 on device: gpio-mxs.4
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.090000] Serial: AMBA PL011 UART driver
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.090000] duart: ttyAMA0 at MMIO 0x80074000 (irq = 47) is a PL011 rev2
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.100000] console [ttyAMA0] enabled
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.100000] mxs-usbphy mxs-usbphy.0: initialized usb phy
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.110000] mxs-usbphy mxs-usbphy.1: initialized usb phy
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.120000] bio: create slab <bio-0> at 0
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.130000] mxs-dma mxs-dma-apbh: initialized
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.140000] mxs-dma mxs-dma-apbx: initialized
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.140000] REG-3V3: 3300 mV normal 
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.150000] REG-1V8: 1800 mV normal 
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.150000] USB 5V: 5000 mV normal 
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.150000] VDDIO-SD: 3300 mV normal 
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.160000] Switching to clocksource mxs_timer
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.200000] NET: Registered protocol family 2
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.200000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.210000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.220000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.220000] TCP: Hash tables configured (established 8192 bind 8192)
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.230000] TCP: reno registered
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.230000] UDP hash table entries: 256 (order: 0, 4096 bytes)
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.240000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.250000] NET: Registered protocol family 1
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.250000] RPC: Registered named UNIX socket transport module.
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.260000] RPC: Registered udp transport module.
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.260000] RPC: Registered tcp transport module.
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.270000] RPC: Registered tcp NFSv4.1 backchannel transport module.
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.280000] audit: initializing netlink socket (disabled)
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    0.280000] type=2000 audit(0.280:1): initialized
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.490000] fuse init (API version 7.18)
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.500000] msgmni has been set to 498
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.500000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.510000] io scheduler noop registered (default)
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.520000] uart-pl011 duart: no DMA platform data
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.520000] mxs-auart.1: ttyAPP1 at MMIO 0x8006c000 (irq = 113) is a mxs-auart.1
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.530000] mxs-auart mxs-auart.1: Found APPUART 3.1.0
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.540000] NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    0.550000] Scanning device for bad blocks
Jan 21 13:16:06 homematic-ccu2 user.warn kernel: [    0.730000] Bad eraseblock 889 at 0x000006f20000
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    0.960000] 8 cmdlinepart partitions found on MTD device gpmi-nand
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    0.970000] Creating 8 MTD partitions on "gpmi-nand":
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    0.970000] 0x000000000000-0x000000100000 : "fcb"
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    0.980000] 0x000000100000-0x000000200000 : "bbt"
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    0.990000] 0x000000200000-0x000000300000 : "bootenv"
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    1.000000] 0x000000300000-0x000000480000 : "bootstream0"
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    1.010000] 0x000000480000-0x000000a80000 : "bootstream1"
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    1.010000] 0x000000a80000-0x000000e80000 : "kernel"
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    1.020000] 0x000000e80000-0x000003e80000 : "user"
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    1.030000] 0x000003e80000-0x000010000000 : "root"
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    1.040000] GPMI NAND driver registered. (IMX)
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    1.050000] UBI: attaching mtd7 to ubi0
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    1.050000] UBI: physical eraseblock size:   131072 bytes (128 KiB)
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    1.060000] UBI: logical eraseblock size:    126976 bytes
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    1.060000] UBI: smallest flash I/O unit:    2048
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    1.070000] UBI: VID header offset:          2048 (aligned 2048)
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    1.070000] UBI: data offset:                4096
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    2.780000] UBI: max. sequence number:       0
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    2.820000] UBI: volume 0 ("root") re-sized from 684 to 1528 LEBs
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    2.830000] UBI: attached mtd7 to ubi0
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    2.830000] UBI: MTD device name:            "root"
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    2.830000] UBI: MTD device size:            193 MiB
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    2.840000] UBI: number of good PEBs:        1547
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    2.840000] UBI: number of bad PEBs:         1
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    2.850000] UBI: number of corrupted PEBs:   0
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    2.850000] UBI: max. allowed volumes:       128
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    2.860000] UBI: wear-leveling threshold:    4096
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    2.860000] UBI: number of internal volumes: 1
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    2.870000] UBI: number of user volumes:     1
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    2.870000] UBI: available PEBs:             0
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    2.880000] UBI: total number of reserved PEBs: 1547
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    2.880000] UBI: number of PEBs reserved for bad PEB handling: 15
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    2.890000] UBI: max/mean erase counter: 16/8
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    2.890000] UBI: image sequence number:  2023351556
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    2.900000] UBI: background thread "ubi_bgt0d" started, PID 32
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    2.900000] UBI: attaching mtd6 to ubi1
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    2.910000] UBI: physical eraseblock size:   131072 bytes (128 KiB)
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    2.920000] UBI: logical eraseblock size:    126976 bytes
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    2.920000] UBI: smallest flash I/O unit:    2048
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    2.930000] UBI: VID header offset:          2048 (aligned 2048)
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    2.930000] UBI: data offset:                4096
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    3.360000] UBI: max. sequence number:       3520
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    3.380000] UBI: attached mtd6 to ubi1
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    3.380000] UBI: MTD device name:            "user"
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    3.390000] UBI: MTD device size:            48 MiB
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    3.390000] UBI: number of good PEBs:        384
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    3.400000] UBI: number of bad PEBs:         0
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    3.400000] UBI: number of corrupted PEBs:   0
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    3.410000] UBI: max. allowed volumes:       128
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    3.410000] UBI: wear-leveling threshold:    4096
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    3.420000] UBI: number of internal volumes: 1
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    3.420000] UBI: number of user volumes:     1
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    3.420000] UBI: available PEBs:             0
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    3.430000] UBI: total number of reserved PEBs: 384
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    3.430000] UBI: number of PEBs reserved for bad PEB handling: 3
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    3.440000] UBI: max/mean erase counter: 12/9
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    3.440000] UBI: image sequence number:  2047575981
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    3.450000] UBI: background thread "ubi_bgt1d" started, PID 33
Jan 21 13:16:06 homematic-ccu2 user.err kernel: [    3.460000] UBI error: ubi_init: cannot attach mtd7
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    3.490000] fec_enet_mii_bus: probed
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    3.500000] rtc-rs5c372 0-0032: rs5c372a found, 24hr, driver version 0.6
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    3.510000] rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    3.520000] stmp3xxx-rtc stmp3xxx-rtc: rtc core: registered stmp3xxx-rtc as rtc1
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    3.530000] watchdog watchdog0: watchdog initialized, 115 seconds remaining
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    3.540000] cpuidle: using governor ladder
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    3.540000] cpuidle: using governor menu
Jan 21 13:16:06 homematic-ccu2 user.debug kernel: [    3.550000] Registered led device: power
Jan 21 13:16:06 homematic-ccu2 user.debug kernel: [    3.550000] Registered led device: internet
Jan 21 13:16:06 homematic-ccu2 user.debug kernel: [    3.550000] Registered led device: info
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    3.550000] NET: Registered protocol family 17
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    3.550000] registered taskstats version 1
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    3.560000] rtc-rs5c372 0-0032: setting system clock to 2018-01-21 12:16:02 UTC (1516536962)
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    3.710000] UBIFS: mounted UBI device 0, volume 0, name "root"
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    3.710000] UBIFS: mounted read-only
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    3.720000] UBIFS: file system size:   192622592 bytes (188108 KiB, 183 MiB, 1517 LEBs)
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    3.730000] UBIFS: journal size:       9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    3.730000] UBIFS: media format:       w4/r0 (latest is w4/r0)
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    3.740000] UBIFS: default compressor: lzo
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    3.740000] UBIFS: reserved for root:  0 bytes (0 KiB)
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    3.750000] VFS: Mounted root (ubifs filesystem) readonly on device 0:12.
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    3.760000] devtmpfs: mounted
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    3.770000] Freeing init memory: 116K
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    4.270000] UBIFS: recovery needed
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    4.790000] UBIFS: recovery completed
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    4.790000] UBIFS: mounted UBI device 1, volume 0, name "user"
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    4.800000] UBIFS: file system size:   46473216 bytes (45384 KiB, 44 MiB, 366 LEBs)
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    4.810000] UBIFS: journal size:       9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    4.810000] UBIFS: media format:       w4/r0 (latest is w4/r0)
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    4.820000] UBIFS: default compressor: lzo
Jan 21 13:16:06 homematic-ccu2 user.notice kernel: [    4.820000] UBIFS: reserved for root:  0 bytes (0 KiB)
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    5.490000] eq3spi eq3spi.0: master is unqueued, this is deprecated
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    5.570000] input: gpio-keys as /devices/platform/gpio-keys/input/input0
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    5.620000] Freescale High-Speed USB SOC Device Controller driver (Apr 20, 2007)
Jan 21 13:16:06 homematic-ccu2 user.debug kernel: [    5.630000] mxs-usbphy mxs-usbphy.0: enabling gadget mode
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    5.710000] usb0: MAC 00:1a:22:00:05:87
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    5.710000] usb0: HOST MAC 00:1a:22:00:05:86
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    5.720000] g_multi gadget: Mass Storage Function, version: 2009/09/11
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    5.720000] g_multi gadget: Number of LUNs=1
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    5.730000]  lun0: LUN: read only CD-ROM file: /usr/share/eq3/install.iso
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    5.740000] g_multi gadget: Multifunction Composite Gadget
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    5.740000] g_multi gadget: g_multi ready
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    5.750000] fsl-usb2-udc: bind to driver g_multi
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    5.780000] tun: Universal TUN/TAP device driver, 1.6
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    5.780000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    5.860000] usbcore: registered new interface driver usbfs
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    5.870000] usbcore: registered new interface driver hub
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    5.870000] usbcore: registered new device driver usb
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    5.900000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    5.910000] mxs-ehci mxs-ehci.1: initializing i.MX USB Controller
Jan 21 13:16:06 homematic-ccu2 user.debug kernel: [    5.920000] mxs-usbphy mxs-usbphy.1: enabling host mode
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    5.940000] mxs-ehci mxs-ehci.1: using regulator to control VBUS
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    5.940000] mxs-ehci mxs-ehci.1: Freescale On-Chip EHCI Host Controller
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    5.950000] mxs-ehci mxs-ehci.1: new USB bus registered, assigned bus number 1
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    5.990000] mxs-ehci mxs-ehci.1: irq 92, io mem 0x80090000
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    6.010000] mxs-ehci mxs-ehci.1: USB 2.0 started, EHCI 1.00
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    6.010000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    6.020000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    6.030000] usb usb1: Product: Freescale On-Chip EHCI Host Controller
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    6.030000] usb usb1: Manufacturer: Linux 3.4.11.ccu2 ehci_hcd
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    6.040000] usb usb1: SerialNumber: mxs-ehci.1
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    6.040000] hub 1-0:1.0: USB hub found
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    6.050000] hub 1-0:1.0: 1 port detected
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    6.080000] mxs-raw-auart mxs-raw-auart.0: Found raw APPUART 3.1.0
Jan 21 13:16:06 homematic-ccu2 user.info kernel: [    6.610000] ip_tables: (C) 2000-2006 Netfilter Core Team
Jan 21 13:16:06 homematic-ccu2 user.err kernel: 0>[    7.370000] udevd[118]: starting version 182
Jan 21 12:16:06 homematic-ccu2 daemon.err udevd[118]: specified group 'dialout' unknown
Jan 21 12:16:06 homematic-ccu2 daemon.err udevd[118]: specified group 'kmem' unknown
Jan 21 12:16:06 homematic-ccu2 daemon.err udevd[118]: specified group 'video' unknown
Jan 21 12:16:06 homematic-ccu2 daemon.err udevd[118]: specified group 'lp' unknown
Jan 21 12:16:06 homematic-ccu2 daemon.err udevd[118]: specified group 'floppy' unknown
Jan 21 12:16:06 homematic-ccu2 daemon.err udevd[118]: specified group 'cdrom' unknown
Jan 21 12:16:06 homematic-ccu2 daemon.err udevd[118]: specified group 'tape' unknown
Jan 21 13:16:07 homematic-ccu2 user.info kernel: [    8.550000] mxs-mmc mxs-mmc.0: using regulator to control VDDIO-SD
Jan 21 13:16:07 homematic-ccu2 user.info kernel: [    8.570000] mxs-mmc mxs-mmc.0: initialized
Jan 21 13:16:08 homematic-ccu2 daemon.info udhcpd[153]: udhcpd (v1.20.2) started
Jan 21 13:16:08 homematic-ccu2 daemon.err udhcpd[153]: can't open '/var/lib/misc/udhcpd.leases': No such file or directory
Jan 21 13:16:08 homematic-ccu2 user.info kernel: [    9.910000] eth0: Freescale FEC PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=imx28-fec-1:00, irq=185)
Jan 21 13:16:10 homematic-ccu2 user.info kernel: [   11.910000] PHY: imx28-fec-1:00 - Link is Up - 100/Full
Jan 21 12:16:14 homematic-ccu2 daemon.info ifplugd(eth0)[265]: ifplugd 0.28 initializing.
Jan 21 12:16:14 homematic-ccu2 daemon.info ifplugd(eth0)[265]: Using interface eth0/00:1A:22:06:05:76 with driver <fec> (version: Revision: 1.0)
Jan 21 12:16:14 homematic-ccu2 daemon.info ifplugd(eth0)[265]: Using detection mode: SIOCETHTOOL
Jan 21 12:16:14 homematic-ccu2 daemon.info ifplugd(eth0)[265]: Initialization complete, link beat detected.
Jan 21 12:16:14 homematic-ccu2 daemon.info ifplugd(eth0)[265]: Executing '/etc/ifplugd/ifplugd.action eth0 up'.
Jan 21 12:16:14 homematic-ccu2 daemon.warn ifplugd(eth0)[265]: client: ifup: interface eth0 already configured
Jan 21 12:16:14 homematic-ccu2 daemon.info ifplugd(eth0)[265]: Program executed successfully.
Jan 21 13:16:15 homematic-ccu2 user.debug setclock: Try to get time from ntp.homematic.com
Jan 21 13:16:16 homematic-ccu2 user.debug setclock: Sun Jan 21 13:16:16 CET 2018
Jan 21 12:16:16 homematic-ccu2 user.info logger: Updating RF Lan Gateway Coprocessor Firmware
Jan 21 12:16:16 homematic-ccu2 user.debug update-coprocessor: firmware filename is: coprocessor_update_hm_only.eq3
Jan 21 12:16:16 homematic-ccu2 user.info logger: Updating RF Lan Gateway Firmware
Jan 21 12:16:16 homematic-ccu2 user.info update-lgw-firmware: No gateway found in config file /etc/config/rfd.conf
Jan 21 12:16:17 homematic-ccu2 user.info logger: Updating Wired Lan Gateway Firmware
Jan 21 12:16:17 homematic-ccu2 user.info update-lgw-firmware: No gateway found in config file /etc/config/hs485d.conf
Jan 21 13:16:23 homematic-ccu2 user.info update-coprocessor: Version: 2.8.6
Jan 21 13:16:23 homematic-ccu2 user.info update-coprocessor: Update necessary, installed: 2.8.6, avaiable 2.8.5
Jan 21 13:16:31 homematic-ccu2 user.info update-coprocessor: Firmwareupdate successfull
Jan 21 13:16:32 homematic-ccu2 user.info kernel: [   34.040000] eq3loop: created slave ttyS0
Jan 21 13:16:32 homematic-ccu2 user.info kernel: [   34.060000] eq3loop: created slave mmd_bidcos
Jan 21 13:16:33 homematic-ccu2 user.err multimac: No Coprocessor detected!!! 
Jan 21 13:16:33 homematic-ccu2 user.info kernel: [   35.070000] eq3loop: eq3loop_close_master() ttyS0
Jan 21 13:16:33 homematic-ccu2 user.info kernel: [   35.070000] eq3loop: eq3loop_close_master() ttyS0 destroy device
Jan 21 13:16:33 homematic-ccu2 user.info kernel: [   35.080000] eq3loop: eq3loop_close_master() mmd_bidcos
Jan 21 13:16:33 homematic-ccu2 user.info kernel: [   35.090000] eq3loop: eq3loop_close_master() mmd_bidcos destroy device
Jan 21 13:16:35 homematic-ccu2 user.err rfd: CCU2CommController::improvedInit() - Identify response string not handled: 
Jan 21 13:16:40 homematic-ccu2 user.err rfd: () CCU2CommController::setCSMACAEnabled(): Error disabling CSMA/CA.
Jan 21 13:16:40 homematic-ccu2 user.err rfd: No BidCoS-Interface available
Jan 21 13:26:41 homematic-ccu2 user.info : hss_lcd: Programm initialisiert.
Jan 21 12:26:42 homematic-ccu2 daemon.info init: starting pid 493, tty '/dev/ttyAMA0': '/sbin/getty -L ttyAMA0 115200 vt100 '
Jan 21 12:26:42 homematic-ccu2 daemon.info init: starting pid 494, tty '/dev/ttyGS0': '/sbin/getty -L ttyGS0 115200 vt100 '
Jan 21 13:26:49 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRpcClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Jan 21 13:26:49 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcMethod: execute failed; method =init Params = {"xmlrpc_bin://127.0.0.1:1999","1007"} result= nil [iseXmlRpc.cpp:2635]
Jan 21 13:26:49 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallInit: CallXmlrpcMethod failed [iseXmlRpc.cpp:1227]
Jan 21 13:26:49 homematic-ccu2 local0.err ReGaHss: Error: XmlRpcClientThread::ThreadFunction(): failed call init for interface=BidCos-RF [iseRTHss.cpp:163]
Jan 21 13:26:49 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRpcClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Jan 21 13:26:49 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcMethod: execute failed; method =init Params = {"xmlrpc_bin://127.0.0.1:1999","1008"} result= nil [iseXmlRpc.cpp:2635]
Jan 21 13:26:49 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallInit: CallXmlrpcMethod failed [iseXmlRpc.cpp:1227]
Jan 21 13:26:49 homematic-ccu2 local0.err ReGaHss: Error: XmlRpcClientThread::ThreadFunction(): failed call init for interface=VirtualDevices [iseRTHss.cpp:163]
Jan 21 13:26:49 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRpcClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Jan 21 13:26:49 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcMethod: execute failed; method =init Params = {"xmlrpc_bin://127.0.0.1:1999","1009"} result= nil [iseXmlRpc.cpp:2635]
Jan 21 13:26:49 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallInit: CallXmlrpcMethod failed [iseXmlRpc.cpp:1227]
Jan 21 13:26:49 homematic-ccu2 local0.err ReGaHss: Error: XmlRpcClientThread::ThreadFunction(): failed call init for interface=HmIP-RF [iseRTHss.cpp:163]
Jan 21 13:57:12 homematic-ccu2 auth.info sshd[737]: Server listening on 0.0.0.0 port 22.
Jan 21 13:59:06 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:06 homematic-ccu2 syslog.info syslogd exiting
Jan 21 13:59:06 homematic-ccu2 syslog.info syslogd started: BusyBox v1.20.2
Jan 21 13:59:06 homematic-ccu2 user.notice kernel: klogd started: BusyBox v1.20.2 (2017-10-11 14:29:35 CEST)
Jan 21 13:59:07 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:07 homematic-ccu2 local0.info ReGaHss: Info: recvd 733 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:07 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /esp/system.htm?sid=@ahIUNR98MY@&action=UpdateUI [iseSession.cpp:185]
Jan 21 13:59:07 homematic-ccu2 local0.info ReGaHss: Info: GetBinValueName0: value not exists. [iseDOMdp.cpp:486]
Jan 21 13:59:07 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:10 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:10 homematic-ccu2 local0.info ReGaHss: Info: recvd 379 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:10 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /tclrega.exe [iseSession.cpp:185]
Jan 21 13:59:10 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:10 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:10 homematic-ccu2 local0.info ReGaHss: Info: recvd 733 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:10 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /esp/system.htm?sid=@ahIUNR98MY@&action=UpdateUI [iseSession.cpp:185]
Jan 21 13:59:10 homematic-ccu2 local0.info ReGaHss: Info: GetBinValueName0: value not exists. [iseDOMdp.cpp:486]
Jan 21 13:59:10 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:13 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:13 homematic-ccu2 local0.info ReGaHss: Info: recvd 733 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:13 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /esp/system.htm?sid=@ahIUNR98MY@&action=UpdateUI [iseSession.cpp:185]
Jan 21 13:59:13 homematic-ccu2 local0.info ReGaHss: Info: GetBinValueName0: value not exists. [iseDOMdp.cpp:486]
Jan 21 13:59:13 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:15 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:15 homematic-ccu2 local0.info ReGaHss: Info: recvd 379 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:15 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /tclrega.exe [iseSession.cpp:185]
Jan 21 13:59:15 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:16 homematic-ccu2 local0.info ReGaHss: Info: recvd 733 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:16 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /esp/system.htm?sid=@ahIUNR98MY@&action=UpdateUI [iseSession.cpp:185]
Jan 21 13:59:16 homematic-ccu2 local0.info ReGaHss: Info: GetBinValueName0: value not exists. [iseDOMdp.cpp:486]
Jan 21 13:59:16 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:16 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:19 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:19 homematic-ccu2 local0.info ReGaHss: Info: recvd 153 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:19 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /tclrega.exe [iseSession.cpp:185]
Jan 21 13:59:19 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:19 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:19 homematic-ccu2 local0.info ReGaHss: Info: recvd 157 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:19 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /tclrega.exe [iseSession.cpp:185]
Jan 21 13:59:19 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:19 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:19 homematic-ccu2 local0.info ReGaHss: Info: recvd 733 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:19 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /esp/system.htm?sid=@ahIUNR98MY@&action=UpdateUI [iseSession.cpp:185]
Jan 21 13:59:19 homematic-ccu2 local0.info ReGaHss: Info: GetBinValueName0: value not exists. [iseDOMdp.cpp:486]
Jan 21 13:59:19 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:20 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:20 homematic-ccu2 local0.info ReGaHss: Info: recvd 379 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:20 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /tclrega.exe [iseSession.cpp:185]
Jan 21 13:59:20 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:22 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:22 homematic-ccu2 local0.info ReGaHss: Info: recvd 733 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:22 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /esp/system.htm?sid=@ahIUNR98MY@&action=UpdateUI [iseSession.cpp:185]
Jan 21 13:59:22 homematic-ccu2 local0.info ReGaHss: Info: GetBinValueName0: value not exists. [iseDOMdp.cpp:486]
Jan 21 13:59:22 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:25 homematic-ccu2 local0.info ReGaHss: Info: recvd 379 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:25 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /tclrega.exe [iseSession.cpp:185]
Jan 21 13:59:25 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:25 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:25 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:25 homematic-ccu2 local0.info ReGaHss: Info: recvd 733 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:25 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /esp/system.htm?sid=@ahIUNR98MY@&action=UpdateUI [iseSession.cpp:185]
Jan 21 13:59:25 homematic-ccu2 local0.info ReGaHss: Info: GetBinValueName0: value not exists. [iseDOMdp.cpp:486]
Jan 21 13:59:25 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:28 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:28 homematic-ccu2 local0.info ReGaHss: Info: recvd 733 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:28 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /esp/system.htm?sid=@ahIUNR98MY@&action=UpdateUI [iseSession.cpp:185]
Jan 21 13:59:28 homematic-ccu2 local0.info ReGaHss: Info: GetBinValueName0: value not exists. [iseDOMdp.cpp:486]
Jan 21 13:59:28 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:30 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:30 homematic-ccu2 local0.info ReGaHss: Info: recvd 379 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:30 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /tclrega.exe [iseSession.cpp:185]
Jan 21 13:59:30 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:31 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:31 homematic-ccu2 local0.info ReGaHss: Info: recvd 733 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:31 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /esp/system.htm?sid=@ahIUNR98MY@&action=UpdateUI [iseSession.cpp:185]
Jan 21 13:59:31 homematic-ccu2 local0.info ReGaHss: Info: GetBinValueName0: value not exists. [iseDOMdp.cpp:486]
Jan 21 13:59:31 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:34 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:34 homematic-ccu2 local0.info ReGaHss: Info: recvd 733 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:34 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /esp/system.htm?sid=@ahIUNR98MY@&action=UpdateUI [iseSession.cpp:185]
Jan 21 13:59:34 homematic-ccu2 local0.info ReGaHss: Info: GetBinValueName0: value not exists. [iseDOMdp.cpp:486]
Jan 21 13:59:34 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:35 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:35 homematic-ccu2 local0.info ReGaHss: Info: recvd 379 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:35 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /tclrega.exe [iseSession.cpp:185]
Jan 21 13:59:35 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:36 homematic-ccu2 local0.info ReGaHss: Info: recvd 115 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:36 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /tclrega.exe [iseSession.cpp:185]
Jan 21 13:59:36 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:36 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:37 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:37 homematic-ccu2 local0.info ReGaHss: Info: recvd 733 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:37 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /esp/system.htm?sid=@ahIUNR98MY@&action=UpdateUI [iseSession.cpp:185]
Jan 21 13:59:37 homematic-ccu2 local0.info ReGaHss: Info: GetBinValueName0: value not exists. [iseDOMdp.cpp:486]
Jan 21 13:59:37 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:40 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:40 homematic-ccu2 local0.info ReGaHss: Info: recvd 379 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:40 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /tclrega.exe [iseSession.cpp:185]
Jan 21 13:59:40 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:40 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:40 homematic-ccu2 local0.info ReGaHss: Info: recvd 733 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:40 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /esp/system.htm?sid=@ahIUNR98MY@&action=UpdateUI [iseSession.cpp:185]
Jan 21 13:59:40 homematic-ccu2 local0.info ReGaHss: Info: GetBinValueName0: value not exists. [iseDOMdp.cpp:486]
Jan 21 13:59:40 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:43 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:43 homematic-ccu2 local0.info ReGaHss: Info: recvd 733 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:43 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /esp/system.htm?sid=@ahIUNR98MY@&action=UpdateUI [iseSession.cpp:185]
Jan 21 13:59:43 homematic-ccu2 local0.info ReGaHss: Info: GetBinValueName0: value not exists. [iseDOMdp.cpp:486]
Jan 21 13:59:43 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:45 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:45 homematic-ccu2 local0.info ReGaHss: Info: recvd 379 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:45 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /tclrega.exe [iseSession.cpp:185]
Jan 21 13:59:45 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:46 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:46 homematic-ccu2 local0.info ReGaHss: Info: recvd 733 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:46 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /esp/system.htm?sid=@ahIUNR98MY@&action=UpdateUI [iseSession.cpp:185]
Jan 21 13:59:46 homematic-ccu2 local0.info ReGaHss: Info: GetBinValueName0: value not exists. [iseDOMdp.cpp:486]
Jan 21 13:59:46 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:48 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:48 homematic-ccu2 local0.info ReGaHss: Info: recvd 153 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:48 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /tclrega.exe [iseSession.cpp:185]
Jan 21 13:59:48 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:48 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:48 homematic-ccu2 local0.info ReGaHss: Info: recvd 157 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:48 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /tclrega.exe [iseSession.cpp:185]
Jan 21 13:59:48 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:48 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:48 homematic-ccu2 local0.info ReGaHss: Info: recvd 441 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:48 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /tclrega.exe [iseSession.cpp:185]
Jan 21 13:59:48 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:49 homematic-ccu2 local0.debug ReGaHss: Verbose: TimerThread::ThreadFunction: ISETIMEZONE = -3600 [iseRTTimer.cpp:81]
Jan 21 13:59:49 homematic-ccu2 local0.debug ReGaHss: Verbose: FillTimerEventList: DST offset = 0 [iseRTTimer.cpp:422]
Jan 21 13:59:49 homematic-ccu2 local0.debug ReGaHss: Verbose: IseRT::SetFinishedDPInitEvent: TimerInitDPsComplete event setting [iseRT.cpp:377]
Jan 21 13:59:49 homematic-ccu2 local0.info ReGaHss: Info: TimerThread::ThreadFunction() - no timer exists, so Wait (60 s) ! [iseRTTimer.cpp:209]
Jan 21 13:59:49 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:49 homematic-ccu2 local0.info ReGaHss: Info: recvd 379 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:49 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /tclrega.exe [iseSession.cpp:185]
Jan 21 13:59:49 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:50 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:50 homematic-ccu2 local0.info ReGaHss: Info: recvd 733 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:50 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /esp/system.htm?sid=@ahIUNR98MY@&action=UpdateUI [iseSession.cpp:185]
Jan 21 13:59:50 homematic-ccu2 local0.info ReGaHss: Info: GetBinValueName0: value not exists. [iseDOMdp.cpp:486]
Jan 21 13:59:50 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:50 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:50 homematic-ccu2 local0.info ReGaHss: Info: recvd 379 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:50 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /tclrega.exe [iseSession.cpp:185]
Jan 21 13:59:50 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:50 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:50 homematic-ccu2 local0.info ReGaHss: Info: recvd 153 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:50 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /tclrega.exe [iseSession.cpp:185]
Jan 21 13:59:50 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:50 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:50 homematic-ccu2 local0.info ReGaHss: Info: recvd 157 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:50 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /tclrega.exe [iseSession.cpp:185]
Jan 21 13:59:50 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:53 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:53 homematic-ccu2 local0.info ReGaHss: Info: recvd 379 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:53 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /tclrega.exe [iseSession.cpp:185]
Jan 21 13:59:53 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:53 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:53 homematic-ccu2 local0.info ReGaHss: Info: recvd 379 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:53 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /tclrega.exe [iseSession.cpp:185]
Jan 21 13:59:53 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:53 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:53 homematic-ccu2 local0.info ReGaHss: Info: recvd 153 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:53 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /tclrega.exe [iseSession.cpp:185]
Jan 21 13:59:53 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:53 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:53 homematic-ccu2 local0.info ReGaHss: Info: recvd 733 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:53 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /esp/system.htm?sid=@ahIUNR98MY@&action=UpdateUI [iseSession.cpp:185]
Jan 21 13:59:53 homematic-ccu2 local0.info ReGaHss: Info: GetBinValueName0: value not exists. [iseDOMdp.cpp:486]
Jan 21 13:59:53 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:54 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:54 homematic-ccu2 local0.info ReGaHss: Info: recvd 157 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:54 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /tclrega.exe [iseSession.cpp:185]
Jan 21 13:59:54 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:55 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:55 homematic-ccu2 local0.info ReGaHss: Info: recvd 379 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:55 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /tclrega.exe [iseSession.cpp:185]
Jan 21 13:59:55 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:56 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:56 homematic-ccu2 local0.info ReGaHss: Info: recvd 733 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:56 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /esp/system.htm?sid=@ahIUNR98MY@&action=UpdateUI [iseSession.cpp:185]
Jan 21 13:59:56 homematic-ccu2 local0.info ReGaHss: Info: GetBinValueName0: value not exists. [iseDOMdp.cpp:486]
Jan 21 13:59:56 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:57 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:57 homematic-ccu2 local0.info ReGaHss: Info: recvd 153 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:57 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /tclrega.exe [iseSession.cpp:185]
Jan 21 13:59:57 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:57 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:57 homematic-ccu2 local0.info ReGaHss: Info: recvd 157 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:57 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /tclrega.exe [iseSession.cpp:185]
Jan 21 13:59:57 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:57 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:57 homematic-ccu2 local0.info ReGaHss: Info: recvd 140 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:57 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /tclrega.exe [iseSession.cpp:185]
Jan 21 13:59:57 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:58 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:58 homematic-ccu2 local0.info ReGaHss: Info: recvd 379 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:58 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /tclrega.exe [iseSession.cpp:185]
Jan 21 13:59:58 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:59 homematic-ccu2 local0.info ReGaHss: Info: recvd 153 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:59 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /tclrega.exe [iseSession.cpp:185]
Jan 21 13:59:59 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:59 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]
Jan 21 13:59:59 homematic-ccu2 local0.info ReGaHss: Info: recvd 157 bytes by web server #0 [httpServer.cpp:766]
Jan 21 13:59:59 homematic-ccu2 local0.info ReGaHss: Info: IseSession GetSessionId from URL: /tclrega.exe [iseSession.cpp:185]
Jan 21 13:59:59 homematic-ccu2 local0.info ReGaHss: Info: http id #0 sends parsed file [httpServer.cpp:2024]
Jan 21 13:59:59 homematic-ccu2 local0.info ReGaHss: Info: start web processing, worker thread #0 {"HTTP-Listener"} [httpListener.cpp:205]


Nachtrag:

ok zu früh gefreut. jetzt gehen die menüs wieder nicht auf.... wenigstens konnte ich einmal ein log erzeugen
Nach oben
Benutzeravatar
anli
Beiträge: 4326
Registriert: 10.06.2009, 14:01
Wohnort: 20 Min. nördlich von Hannover und bei Bremen
Hat sich bedankt: 1 Mal
Danksagung erhalten: 23 Mal
Kontaktdaten:
Kontaktdaten von anli

Re: CCU2 Menüs gehen nicht richtig auf

Beitrag von anli » 21.01.2018, 16:26

Super, sehr gut. Hast Du die CCU2 gerade gekauft? Ich vermute, dass diese defekt ist:
Granten hat geschrieben:

Code: Alles auswählen

Jan 21 13:16:23 homematic-ccu2 user.info update-coprocessor: Version: 2.8.6
Jan 21 13:16:23 homematic-ccu2 user.info update-coprocessor: Update necessary, installed: 2.8.6, avaiable 2.8.5
Jan 21 13:16:31 homematic-ccu2 user.info update-coprocessor: Firmwareupdate successfull
Jan 21 13:16:32 homematic-ccu2 user.info kernel: [   34.040000] eq3loop: created slave ttyS0
Jan 21 13:16:32 homematic-ccu2 user.info kernel: [   34.060000] eq3loop: created slave mmd_bidcos
Jan 21 13:16:33 homematic-ccu2 user.err multimac: No Coprocessor detected!!! 
Jan 21 13:16:33 homematic-ccu2 user.info kernel: [   35.070000] eq3loop: eq3loop_close_master() ttyS0
Jan 21 13:16:33 homematic-ccu2 user.info kernel: [   35.070000] eq3loop: eq3loop_close_master() ttyS0 destroy device
Jan 21 13:16:33 homematic-ccu2 user.info kernel: [   35.080000] eq3loop: eq3loop_close_master() mmd_bidcos
Jan 21 13:16:33 homematic-ccu2 user.info kernel: [   35.090000] eq3loop: eq3loop_close_master() mmd_bidcos destroy device
Jan 21 13:16:35 homematic-ccu2 user.err rfd: CCU2CommController::improvedInit() - Identify response string not handled: 
Jan 21 13:16:40 homematic-ccu2 user.err rfd: () CCU2CommController::setCSMACAEnabled(): Error disabling CSMA/CA.
Jan 21 13:16:40 homematic-ccu2 user.err rfd: No BidCoS-Interface available
Er will ein Update der Copro Firmware machen, scheint zu gelingen, aber er kann den Copro dann nicht ansteuern. Wenn die CCU2 neu ist, rate ich zum Umtausch. Wenn sie nicht neu ist, mal aufschrauben und auf kalte Lötstellen besonders im Bereich des Funkmoduls prüfen.
Herzliche Grüße, anli

Alle Angaben ohne Gewähr und Haftung meinerseits. Verwendung der von mir zur Verfügung gestellten Downloads auf eigene Gefahr. Ich bitte um Verständnis, dass ich aus zeitlichen Gründen keine unaufgeforderte Hilfestellung per PN/Mail geben kann. Bitte allgemeine Fragen ins Forum stellen, hier können viele fähige User viel schneller helfen.

Homematic-Manager v2: einfaches Tool zum Erstellen von Direktverknüpfungen und Bearbeiten von Gerätenamen, -parametern etc. für Homematic und HomematicIP (Alternative diesbzgl. zur WebUI)

Einsteiger-Hilfe • erweiterter Skript-Parser
Nach oben
Granten
Beiträge: 37
Registriert: 18.12.2016, 16:35

Re: CCU2 Menüs gehen nicht richtig auf

Beitrag von Granten » 21.01.2018, 16:29

anli hat geschrieben:Wenn die CCU2 neu ist, rate ich zum Umtausch.
gekauft habe ich sie am 14. November 2016. meinst du da ist noch garantie drauf?
Nach oben
Benutzeravatar
anli
Beiträge: 4326
Registriert: 10.06.2009, 14:01
Wohnort: 20 Min. nördlich von Hannover und bei Bremen
Hat sich bedankt: 1 Mal
Danksagung erhalten: 23 Mal
Kontaktdaten:
Kontaktdaten von anli

Re: CCU2 Menüs gehen nicht richtig auf

Beitrag von anli » 21.01.2018, 16:33

Granten hat geschrieben:
anli hat geschrieben:Wenn die CCU2 neu ist, rate ich zum Umtausch.
gekauft habe ich sie am 14. November 2016. meinst du da ist noch garantie drauf?
Wenn ich es richtig weiß ist bei Privatverbrauchern die Garantie gesetzlich vorgeschrieben ja immer nur ein halbes Jahr, danach für 1,5 Jahre Gewährleistung (Beweislastumkehr). Die meisten Händler handhaben die Garantie jedoch großzügiger und gewähren auch in der Gewährleistungsphase (teilweise) Garantieleistungen. Abgesehen davon sollte es auch hier mit der Gewährleistung klappen (Fehler muss ja schon bei Auslieferung bestanden haben). Insofern würde ich auf jeden Fall einen Tausch im Rahmen einer Garantie/Gewährleistung probieren.

Siehe auch https://de.wikipedia.org/wiki/Garantie, Abschnitt "Abgrenzung der Qualitätsgarantie gegenüber der Gewährleistung"
Herzliche Grüße, anli

Alle Angaben ohne Gewähr und Haftung meinerseits. Verwendung der von mir zur Verfügung gestellten Downloads auf eigene Gefahr. Ich bitte um Verständnis, dass ich aus zeitlichen Gründen keine unaufgeforderte Hilfestellung per PN/Mail geben kann. Bitte allgemeine Fragen ins Forum stellen, hier können viele fähige User viel schneller helfen.

Homematic-Manager v2: einfaches Tool zum Erstellen von Direktverknüpfungen und Bearbeiten von Gerätenamen, -parametern etc. für Homematic und HomematicIP (Alternative diesbzgl. zur WebUI)

Einsteiger-Hilfe • erweiterter Skript-Parser
Nach oben
Granten
Beiträge: 37
Registriert: 18.12.2016, 16:35

Re: CCU2 Menüs gehen nicht richtig auf

Beitrag von Granten » 21.01.2018, 16:48

die gesetzliche lage kenn ich. ich meinte eher wie es eq-3 handhabt.
ich habe mal den support dort kontaktiert und hoffe keine 100€ in den sand gesetzt zu haben....
Nach oben
Antworten

Zurück zu „HomeMatic Zentrale (CCU / CCU2 / CCU3 / Charly)“