Mir ist da nix zu einem 5°C Bug in Zusammenhang mit einer CCU bekannt.
Vielleicht betrifft (betraf) das nur die EVO's die du hattest.
Heizprofile wöchentlich automatisch wechseln
Moderator: Co-Administratoren
- Baxxy
- Beiträge: 10748
- Registriert: 18.12.2018, 15:45
- System: Alternative CCU (auf Basis OCCU)
- Hat sich bedankt: 599 Mal
- Danksagung erhalten: 2199 Mal
Re: Heizprofile wöchentlich automatisch wechseln
Grüße... Baxxy
- Raspberry Pi 4 als Homematic-Zentrale - Tipps und Informationen
- Analysescript für genutzte Funk-Adressen, Funkmodul-Hardware und Zentralen Hardware
- NANO CUL 868MHz - Stick zum AskSin Analyzer XS umflashen (Anleitung für ArduinoIDE unter Windows)
- Firmware Updates für IP-Aktoren / Sensoren... Info's, Tipps und Sonstiges
- CCU funkt nicht - CarrierSense (CS) Probleme erkennen und lösen
- Baxxy
- Beiträge: 10748
- Registriert: 18.12.2018, 15:45
- System: Alternative CCU (auf Basis OCCU)
- Hat sich bedankt: 599 Mal
- Danksagung erhalten: 2199 Mal
Re: Heizprofile wöchentlich automatisch wechseln
Also wenn ich mir das Changelog zum EVO so angucke würde ich sagen das wurde gefixt mit den 5°C.
Version 1.2.000 - 2022-06-01
--------------------------------------------------------------
* Bugfix
* Correction for MANU set point temperature update after window open.
If window open is detected (extern/intern) and during this time the device get
the command "Eco-Mode", the device updated the set point temperature after window
close and "Eco-Mode" off to the old set point temperature.
* Valve remains closed after decalcification.
After performing the decalcification run, the valve initially remained closed, and
only after a new valve position was calculated was the valve opened again.
* Setting vacation/party mode not possible.
Due to the hot-fix in 1.0.12 the vacation/party mode could no longer be activated.
Version 1.0.012 - 2022-01-27
--------------------------------------------------------------
* Bugfix
* Week program 2 and 3 not usable
If the week program 2 or 3 was set, 5.0 °C was permanently set as the setpoint
temperature. No matter what was previously configured in the profile.
Version 1.0.010 - earlier
--------------------------------------------------------------
First Release.
Grüße... Baxxy
- Raspberry Pi 4 als Homematic-Zentrale - Tipps und Informationen
- Analysescript für genutzte Funk-Adressen, Funkmodul-Hardware und Zentralen Hardware
- NANO CUL 868MHz - Stick zum AskSin Analyzer XS umflashen (Anleitung für ArduinoIDE unter Windows)
- Firmware Updates für IP-Aktoren / Sensoren... Info's, Tipps und Sonstiges
- CCU funkt nicht - CarrierSense (CS) Probleme erkennen und lösen
Re: Heizprofile wöchentlich automatisch wechseln
Also dann doch mal danke.
So, jetzt muss ich mich nur noch entscheiden zwischen Bosch oder Homematic ip.
So, jetzt muss ich mich nur noch entscheiden zwischen Bosch oder Homematic ip.
-
- Beiträge: 6722
- Registriert: 22.05.2012, 08:40
- System: CCU
- Hat sich bedankt: 25 Mal
- Danksagung erhalten: 479 Mal
Re: Heizprofile wöchentlich automatisch wechseln
Das sind nur zwei vollkommen unterschiedliche Systeme, Bosch arbeitet mit Zigbee 3.0 als Funkprotokoll während eQ-3 ein proprietäres Funkprotokoll für Homematic IP nutzt.
Re: Heizprofile wöchentlich automatisch wechseln
Das Funkprotokoll/ Funkstandard hat nichts mit dem Ursprungsthread und dem 5°C Bug zu tun.
Ich schreibe hier nun nicht mehr weiter, dafür werde ich ein neues Thema öffnen.
Ich schreibe hier nun nicht mehr weiter, dafür werde ich ein neues Thema öffnen.