Hello,
I have the homematic CCU3 and installed the following components:
- each room has a wall thermostat
- downstairs i have 4 rooms with floor heating, with the HmIP-FAL230-C10 floor heating module (with 12 zones installed with a motorized valve on it)
- upstairs i have 5 rooms with a wall thermostat and a radiator valve
- the boiler is hooked up to a WHS2 switching module
All i want is the boiler to switch on when there is heat demand, and switch off the boiler when there's not.
I used groups for each room:
-downstairs -> each group has the wall thermostat and the corresponding floor zones in it
-upstars -> each group has the wall thermostat and the radiator valve in it.
i'm a bit lost on how to properly set the WHS 2 to switch the boiler automatically whenever there is heat demand.
I made a program in the ccu3 that whenever upstairs the valve of any room is opened more then 10% -> switch output WHS2 to on. Is this the correct way?
Downstairs i don't know how to get this result with the floor actuators? Also the living room has 5 zones of the floor heating in a group. But sometimes, some of these are open while others are closed so parts of the floor are warm, while other parts stay cooler.
Any help guiding me in the right direction is much appreciated. If i need to provide more info, let me know.
Thanks!
CCU 3 boiler on/off per room
Support for our english speaking visitors
Moderator: Co-Administratoren
-
- Beiträge: 1
- Registriert: 26.11.2024, 11:57
- System: sonstige
Zurück zu „HomeMatic - english“
Gehe zu
- Allgemein
- ↳ Informationen zum HomeMatic-Forum
- ↳ Neubau - Renovierung - Planung
- ↳ Projektvorstellungen
- ↳ Usertreffen und Stammtische
- ↳ Vergangene Aktivitäten
- ↳ OffTopic
- ↳ Tiergarten
- HomeMatic
- ↳ HomeMatic allgemein
- ↳ HomeMatic Tipps & Tricks - keine Fragen!
- ↳ HomeMatic Zentrale (CCU / CCU2 / CCU3 / Charly)
- ↳ HmIP-HCU - Home Control Unit
- ↳ HomeMatic OCCU
- ↳ Allgemeines zur OCCU
- ↳ OCCU Entwicklung
- ↳ debmatic
- ↳ piVCCU
- ↳ RaspberryMatic
- ↳ x86-CCU
- ↳ YAHM
- ↳ HomeMatic Aktoren und Sensoren (klassisch)
- ↳ HomeMatic IP Aktoren und Sensoren
- ↳ HomeMatic IP wired Aktoren und Sensoren
- ↳ HomeMatic IP mit Access Point
- ↳ HomeMatic IP mit CCU
- ↳ HomeMatic - bekannte Bugs
- ↳ HomeMatic Addons
- ↳ CCU-Historian
- ↳ CCU.IO
- ↳ CCU-Jack
- ↳ CloudMatic
- ↳ CUxD
- ↳ Hue-Addon
- ↳ RedMatic
- ↳ WebMatic
- ↳ Sonstige Addons
- ↳ HomeMatic Entwicklung
- ↳ Softwareentwicklung für die HomeMatic CCU
- ↳ Softwareentwicklung von externen Applikationen
- ↳ Hardwareentwicklung und Selbstbau von Aktoren und Sensoren
- ↳ 3D-Druck
- ↳ HomeMatic Apps und Desktop-Anwendungen
- ↳ TinyMatic
- ↳ Externe Steuerungen und Visualisierungen
- ↳ Home Assistant
- ↳ homeputer CL
- ↳ homeputer CL - Bugs & Updatewünsche
- ↳ IP-Symcon
- ↳ mediola
- ↳ openHAB
- ↳ Sonstige Steuerungen und Visualisierungen
- ↳ HomeMatic - english
- FHZ-, FS20-, HMS100-, FHT-, KeyMatic- & sonstige Hardware
- ↳ ELV FHZ Funk-Hauszentralen
- ↳ ELV FS20 Sender, Empfänger und Aktoren
- ↳ ELV HMS-Alarm Sensoren und Aktoren
- ↳ ELV FHT-Komponenten
- ↳ ELV Wettersensoren / Wetterstationen
- ↳ ELV KeyMatic Funk-Codeschloss & Türschlossantrieb
- ↳ Sonstige Hardware (Vellemann USB-Board, IRTrans, ALLNET)
- FHZ Software / Programmierung
- ↳ homeputer Studio / Standard: allgemeine Fragen
- ↳ homeputer Studio / Standard: Programmierbeispiele
- ↳ homeputer Studio / Standard: Bugs & Updatewünsche
- ↳ FHZ unter Linux / MacOSX
- Markt
- ↳ Private Kleinanzeigen