Is it possible to reset the self calibration these do?
I previously had my heating set to trigger when any valve exceeded 20%. I've now pushed that up to 30% as i found it recycling a bit too much at 20.
Unfortunately a couple of the valves, particularly those that would often be open on their own, seem to "stick" in the low 20's even when the recorded temperature is some way below the set temp, presumable because preciously this would be enough to heat the room but now means the heating doesn't come on.
Would like to reset the calibration and hopefully without having to re-teach all the components!
HM-CC-RT-DN valve position optimisation
Support for our english speaking visitors
Moderator: Co-Administratoren
Zurück zu „HomeMatic - english“
Gehe zu
- Allgemein
- ↳ Informationen zum HomeMatic-Forum
- ↳ Neubau - Renovierung - Planung
- ↳ Projektvorstellungen
- ↳ Usertreffen und Stammtische
- ↳ Vergangene Aktivitäten
- ↳ OffTopic
- ↳ Tiergarten
- HomeMatic
- ↳ HomeMatic allgemein
- ↳ HomeMatic Tipps & Tricks - keine Fragen!
- ↳ HomeMatic Zentrale (CCU / CCU2 / CCU3 / Charly)
- ↳ HmIP-HCU - Home Control Unit
- ↳ HomeMatic OCCU
- ↳ Allgemeines zur OCCU
- ↳ OCCU Entwicklung
- ↳ debmatic
- ↳ piVCCU
- ↳ RaspberryMatic
- ↳ x86-CCU
- ↳ YAHM
- ↳ HomeMatic Aktoren und Sensoren (klassisch)
- ↳ HomeMatic IP Aktoren und Sensoren
- ↳ HomeMatic IP wired Aktoren und Sensoren
- ↳ HomeMatic IP mit Access Point
- ↳ HomeMatic IP mit CCU
- ↳ HomeMatic - bekannte Bugs
- ↳ HomeMatic Addons
- ↳ CCU-Historian
- ↳ CCU.IO
- ↳ CCU-Jack
- ↳ CloudMatic
- ↳ CUxD
- ↳ Hue-Addon
- ↳ RedMatic
- ↳ WebMatic
- ↳ Sonstige Addons
- ↳ HomeMatic Entwicklung
- ↳ Softwareentwicklung für die HomeMatic CCU
- ↳ Softwareentwicklung von externen Applikationen
- ↳ Hardwareentwicklung und Selbstbau von Aktoren und Sensoren
- ↳ 3D-Druck
- ↳ HomeMatic Apps und Desktop-Anwendungen
- ↳ TinyMatic
- ↳ Externe Steuerungen und Visualisierungen
- ↳ Home Assistant
- ↳ homeputer CL
- ↳ homeputer CL - Bugs & Updatewünsche
- ↳ IP-Symcon
- ↳ mediola
- ↳ openHAB
- ↳ Sonstige Steuerungen und Visualisierungen
- ↳ HomeMatic - english
- FHZ-, FS20-, HMS100-, FHT-, KeyMatic- & sonstige Hardware
- ↳ ELV FHZ Funk-Hauszentralen
- ↳ ELV FS20 Sender, Empfänger und Aktoren
- ↳ ELV HMS-Alarm Sensoren und Aktoren
- ↳ ELV FHT-Komponenten
- ↳ ELV Wettersensoren / Wetterstationen
- ↳ ELV KeyMatic Funk-Codeschloss & Türschlossantrieb
- ↳ Sonstige Hardware (Vellemann USB-Board, IRTrans, ALLNET)
- FHZ Software / Programmierung
- ↳ homeputer Studio / Standard: allgemeine Fragen
- ↳ homeputer Studio / Standard: Programmierbeispiele
- ↳ homeputer Studio / Standard: Bugs & Updatewünsche
- ↳ FHZ unter Linux / MacOSX
- Markt
- ↳ Private Kleinanzeigen