New CCU3 Firmware 3.43.15 + HmIP Wired released

[tomi_cc16]

CCU3 Firmware 3.43.15:

New device integration in CCU3:
[HMCCU-6] Integration HmIP-RCV-50 (CCU virtual remote Control from HmIP)
[HMCCU3-1834] Integration HmIP-FCI6 (Contact Interface flush-mount – 6x channels)
[HMCCU3-1502] Integration HmIPW-DRD3 (Homematic IP Wired Dimming Actuator – 3x channels)
[HMCCU3-1501] Integration HmIPW-DRS4 (Homematic IP Wired Swich Actuator – 4x channels)
[HMCCU3-1500] Integration HmIPW-DRS8 (Homematic IP Wired Switch Actuator – 8x channels)
[HMCCU3-1499] Integration HmIPW-FIO6 (Homematic IP Wired IO Module flush-mount – 6x channels)
[HMCCU3-1498] Integration HmIPW-DRI16 (Homematic IP Wired Inbound module – 16x channels)
[HMCCU3-1497] Integration HmIPW-DRI32 (Homematic IP Wired Inbound module – 32x channels)
[HMCCU3-1496] Integration HmIPW-DRBL4 (Homematic IP Wired Blinds Actuator – 4x channels)
[HMCCU3-1495] Integration HmIPW-DRAP (Homematic IP Wired Access Point)
[HMCCU3-1375] Integration HmIP-WT (Homematic IP Wall Thermostat) *probably without Display*
[HMCCU-24] Integration HmIP-ASIR-B1 (Alarm Siren - indoor)
[HMCCU-9] Integration Hm-RC-2-PBU-FM-2 (Wireless Remote Control 2x channels for brand switch systems, flush-mount, 230V)

Enhancements:
[HMCCU3-2116] Config.-Parameter „Optimum Start/Stop“ for HmIP-WT/WTH/WTH2
[HMCCU3-2115] Config.-Parameter „Valve-Offset“ for HmIP-eTRV/-2/-B/-C
[HMCCU3-1926] IP-Adressen (IPv4 / IPv6) under network settings are checked for plausibility
[HMCCU-120] For local connections (localhost) no longer HTTP Basic authentication
is carried out
[HMCCU-109] Relay name changed to output (eg. "status message relay" is now "status message output")
[HMCCU-74] The device firmware button now jumps to the new overview page of the device firmware
[HMCCU-8] The device firmware update is only carried out via the "Device Firmware Overview"
The corresponding button on the device configuration page has been removed.

Corrections:
[HMCCU3-2114] HmIP-BSL - the upper device button was not available for programs
[HMCCU3-2104] HmIP-FBL/BBL - missing lamellar position added in the weekly program
[HMCCU3-2103] HmIP-FBL/BBL - the lamellar position could not be set via the WebUI
[HMCCU3-2095] Configuration window of the RGBW controller restored in programs
[HMCCU3-2093] HmIP-FCI1/6 - added missing Easymodes
[HMCCU3-2088] The function "Action at power supply" for Homematic IP-MP3P and dimming actuators
was faulty
[HMCCU3-2087] HmIP-FCI1/6 - Removed parameter "Event delay"
[HMCCU3-1837] The "Device Firmware Overview" was not loaded correctly with existing Philips HUE Gateway
[HMCCU3-1467] The CCU value of the energy meter doubled after a reboot of the CCU
[HMCCU-97] HmIP-PCBS2 – Residence (latitude / longitude) is now adjustable. The indication is for
a correct execution of the weekly program needed

------------------------------------------------------------------------------------
Personal note since the last November 2018 firmware updates we will have from now on differences between CCU2 and CCU3:

CCU2 Firmware in the future:
- Firmware Update will provide Bug corrections
- some Homematic IP devices will be included

CCU3 Firmware in the future:
- Firmware Update will provide Bug corrections
- new Homematic IP devices will be included especially HmIP Wired
- new security functionalties
- updated API interface
- new functionality to permanently disable generation of service messages for selected devices. Now user can disable all service messages for a device
- a much improved source code editor functionality for the "Test script" and general Script Editor functionality when creating WebUI programs using ReGa-scripts
- and much more functionalities...

For coming updates check also the RaspberryMatic Changelog - the changes will be integrated in the long run also in the CCU3 firmware:
https://github.com/jens-maus/RaspberryMatic/releases

[Harpau]

Beim Versuch, das Update einzuspielen, erscheint die Fehlermeldung "Die hochgeladene Datei enthält keine gültige Software".

[tomi_cc16]

This is the english corner - please in english.

Probably you used Safari and it unpacked it. Dont unpack it and upload the whole file to CCU3.

Here a good YouTube clip in German what to do or don’t do:
https://youtu.be/y_FkxfbXOaE

[hobbyquaker]

Out of curiosity: What is the source of the paragraph "General Info since the last November 2018 firmware updates ..."? The official (german) changelog doesn't include that.

[tomi_cc16]

Hi Sebastian,


this is a personal note/info from the released information and observation of the last months.

Btw. Thank you for all the great Addons and Tools you created

[Roland M.]

Hello!

this is a personal note/info from the released information and observation of the last months.

...than please mark this as personal note!

That can be an issue discussed in Kassel next month, but for now there are no official statements for that.


Roland

[tomi_cc16]

Updated

Just one hint that HmIP Wired will be not supported in CCU2 is already official and with the latest CCU2 firmware eg. those topics were not part:
- updated API interface
- new functionality to permanently disable generation of service messages for selected devices. Now user can disable all service messages for a device
- a much improved source code editor functionality for the "Test script" and general Script Editor functionality when creating WebUI programs using ReGa-scripts
...

And my personal thought is that this will continue like before it was the case for CCU1 firmware vs CCU2 fimware until CCU1 Firmware Updates died.

[Harpau]

Probably you used Safari and it unpacked it. Dont unpack it and upload the whole file to CCU3.

Thanks a lot. This was the reason.

[tomi_cc16]

One important information for all RaspberryMatic Users, HmIP WIRED is only possible with a RPI-RF-MOD !!!

[jmaus]

One important information for all RaspberryMatic Users, HmIP WIRED is only possible with a RPI-RF-MOD !!!

This is nothing specific to RaspberryMatic. The same applies to the CCU3 firmware. HmIP-Wired connectivity is bound to using a RPI-RF-MOD rf module.