Multiple problems in new installation
Verfasst: 13.02.2020, 20:37
Hi all,
Recently I bought a complete set of Homematic IP (cloud based) equipment to control the heating system of my house. At first glance it looks nice and effective, but I'm running in some problems. Perhaps one of you can help me?
My system consists of:
-1x HMIP-HAP
-3x HMIP-MIOB
-2x HMIP-FAL230-C10
-1x HMIP-FAL230-C06
-16x thermostats
In total I have three heating circuits, each controller by one MIOB. One heating circuit is controller by one thermostat, and directly operating one valve and the heater (via MIOB). Two circuits are seperated over different zones, each zone controlled by a thermostat, and connected to the HMIP-FAL's.
At the moment I have the following problems:
-I'm using a HMIP-MIOB controlled by a HMIP_WTH-2 thermostate. If the thermostate is requesting heat, I want the MIOB to close the potential free contact 4.1/4.2. (this will start up me heating). For the moment this is not working, the potential free contact is closed all the time, no matter what temperature I choose
-When changing temperatur on the thermostat it takes a long time (several minutes) before the system reacts, is this normal system behavior?
-the HMIP-FAL230-C10: controls 10 actuators, at the moment it is controlled by one thermostat, thus in my opinion opening or closing all the valves at (roughly) the same time. But at the moment, sometimes, 5 valves are opened, sometimes 2, sometimes 10... what is happening? -->>> FIXED
-I want to use a default temperatur profile, for the moment I have to redefine it for every room again and again... pretty anoying, any ideas?
-Is there some kind of diagnostics mode available, so that I can see the status of all equipment (including port status) on the app, at the moment I have to walk around to see what is happening.
Any help and advice is really appreciated!!
Kind regards,
Joost
Recently I bought a complete set of Homematic IP (cloud based) equipment to control the heating system of my house. At first glance it looks nice and effective, but I'm running in some problems. Perhaps one of you can help me?
My system consists of:
-1x HMIP-HAP
-3x HMIP-MIOB
-2x HMIP-FAL230-C10
-1x HMIP-FAL230-C06
-16x thermostats
In total I have three heating circuits, each controller by one MIOB. One heating circuit is controller by one thermostat, and directly operating one valve and the heater (via MIOB). Two circuits are seperated over different zones, each zone controlled by a thermostat, and connected to the HMIP-FAL's.
At the moment I have the following problems:
-I'm using a HMIP-MIOB controlled by a HMIP_WTH-2 thermostate. If the thermostate is requesting heat, I want the MIOB to close the potential free contact 4.1/4.2. (this will start up me heating). For the moment this is not working, the potential free contact is closed all the time, no matter what temperature I choose
-When changing temperatur on the thermostat it takes a long time (several minutes) before the system reacts, is this normal system behavior?
-the HMIP-FAL230-C10: controls 10 actuators, at the moment it is controlled by one thermostat, thus in my opinion opening or closing all the valves at (roughly) the same time. But at the moment, sometimes, 5 valves are opened, sometimes 2, sometimes 10... what is happening? -->>> FIXED
-I want to use a default temperatur profile, for the moment I have to redefine it for every room again and again... pretty anoying, any ideas?
-Is there some kind of diagnostics mode available, so that I can see the status of all equipment (including port status) on the app, at the moment I have to walk around to see what is happening.
Any help and advice is really appreciated!!
Kind regards,
Joost