Hallo,
ich habe bei meiner Garage einen tür-fensterkontakt so programmiert, dass er nachts beim öffnen auf meiner handy app einen Alarm auslöst.
das habe ich so gelöst, dass ich in der Automatisierung die Aktion "Alarmzustand aktiv" benutzt habe.
Jetzt möchte ich gerne, dass gleichzeitig eine Schaltsteckdose angeschaltet wird,
Wie kann ich das bewerkstelligen beziehungsweise programmieren?
Für eure Hilfe bin ich sehr dankbar
liebe Grüße
Georg
Alarmauslösung auf Schaltsteckdose umleiten
Moderator: Co-Administratoren
-
- Beiträge: 9
- Registriert: 23.03.2019, 16:51
- Hat sich bedankt: 8 Mal
-
- Beiträge: 157
- Registriert: 21.11.2021, 11:53
- System: Access Point
- Danksagung erhalten: 24 Mal
Re: Alarmauslösung auf Schaltsteckdose umleiten
Entweder erstellst du noch eine Automatisierung,
Fensterzustand = geöffnet, Aktion = Steckdose an,
oder du fügst in deine bestehende Automatisierung eine zweite Aktion ein.
Ganz einfach.
Fensterzustand = geöffnet, Aktion = Steckdose an,
oder du fügst in deine bestehende Automatisierung eine zweite Aktion ein.
Ganz einfach.
Gruß, Matze
1x HmIP-HAP, 11x HmIP-eTRV-2, 8x HmIP-SWDO, 1x HmIP-SWDO-I, 1x HmIP-SWDM, 9x HmIP-BROLL, 3x HmIP-DLD, 2x HmIP-KRCK,
9x HmIP-PS, 1x HmIP-PSM, 4x HmIP-PSM-2, 1x HmIP-RC8, 5x HmIP-BSM, 2x HmIP-BSL, 2x HmIP-PCBS, 1x HmIP-PCBS-BAT,
1x HmIP-MOD-TM, 1x HmIP-MOD-OC8, 2x HmIP-WRC2, 1x HmIP-FCI1, 1x HmIP-WKP, 1x HmIP-FCI6, 1x HmIP-SPI, (2x HmIP-FROLL)
Smartha-App zur Visualisierung siehe hier
1x HmIP-HAP, 11x HmIP-eTRV-2, 8x HmIP-SWDO, 1x HmIP-SWDO-I, 1x HmIP-SWDM, 9x HmIP-BROLL, 3x HmIP-DLD, 2x HmIP-KRCK,
9x HmIP-PS, 1x HmIP-PSM, 4x HmIP-PSM-2, 1x HmIP-RC8, 5x HmIP-BSM, 2x HmIP-BSL, 2x HmIP-PCBS, 1x HmIP-PCBS-BAT,
1x HmIP-MOD-TM, 1x HmIP-MOD-OC8, 2x HmIP-WRC2, 1x HmIP-FCI1, 1x HmIP-WKP, 1x HmIP-FCI6, 1x HmIP-SPI, (2x HmIP-FROLL)
Smartha-App zur Visualisierung siehe hier
-
- Beiträge: 9
- Registriert: 23.03.2019, 16:51
- Hat sich bedankt: 8 Mal