HmIP-WTH-2 Firmware 1.8
Moderator: Co-Administratoren
- deimos
- Beiträge: 5396
- Registriert: 20.06.2017, 10:38
- System: Alternative CCU (auf Basis OCCU)
- Wohnort: Leimersheim
- Hat sich bedankt: 121 Mal
- Danksagung erhalten: 957 Mal
- Kontaktdaten:
HmIP-WTH-2 Firmware 1.8
Hi,
grade auf der Website von eQ-3 entdeckt und auch in der CCU Oberfläche, neue HmIP-WTH-2 Firmware gibt es es jetzt auch für die CCU2.
Mal schauen, wie lange das Update bei 9 Geräten dauert, letztes Mal war es grob eine Woche.
Changelog:
Achtung! Bitte verwenden Sie die Firmware-Datei nur in Verbindung mit der CCU2 ab
Version 2.29.22
Please note: Only use the firmware file in connection with the CCU2 from version 2.29.22
Changelog: HmIP-WTH-2
Version 1.8.000 - 20170915
----------------------------------------------------------------------------------------
Version:
Application: 1.8.000
Bootloader: 1.10.000
Library: 1.20.004
** Related Hardware
* 1434158F, 1434177A
** Bugfix
* Correction in Paging-Module HMOS-Library
Catched erros which could occure after an OTAU update to a newer paging module.
* Correction for the Optimum Start Stop function
After activating the optimum start stop function it is now executed correctly.
** Modification
* Change to Version 1.8.000
Parameter extension for installer solution.
With the help of the new parameter "DISABLE_MSG_TO_AC" all transmissions to the
central address are suppressed. Also to the status receiver address if this is the
same as the central address.
Version 1.6.000 - 20170721
----------------------------------------------------------------------------------------
Version:
Application: 1.6.000
Bootloader: 1.10.000
Library: 1.20.003
** Related Hardware
* 1434158F, 1434177A
** Bugfix
* Expansion for inclusion condition.
If parameter changes have been made to the device before the inclusion, the device
can only be included if a factory reset has been performed on the device before.
* Correction for set point temperature update after weekprogram configuration.
If window open is detected (extern/intern) and during this time a new week program
is transmitted to the device, the device updated the set point temperature after
window close by using the new week program set point temperature.
* Correction when changing from auto mode to manu mode.
When changing from auto mode to manu mode and boost is active, boost is abort.
* The date and time are cyclically synchronized with the access point.
In order that date and time are be synchron in system, the data is retrieved every
6 hours at Access point.
* Extension for the Quick Veto Function.
If the quick veto function is active, the remaining time is transferred in the
status telegram.
* Behavior after aborting the factory reset.
If the factory reset is aborted or not executed until the end, the device performs
a reboot after the termination or after the timeout.
* Abort of Quick Veto by "Duration = 0".
If Quick Veto is active, Quick Veto can be aborted by the radio command
"Duration = 0". The device answers the radio telegram with an "Ack".
** Modification
* Change to Version 1.6.000
grade auf der Website von eQ-3 entdeckt und auch in der CCU Oberfläche, neue HmIP-WTH-2 Firmware gibt es es jetzt auch für die CCU2.
Mal schauen, wie lange das Update bei 9 Geräten dauert, letztes Mal war es grob eine Woche.
Changelog:
Achtung! Bitte verwenden Sie die Firmware-Datei nur in Verbindung mit der CCU2 ab
Version 2.29.22
Please note: Only use the firmware file in connection with the CCU2 from version 2.29.22
Changelog: HmIP-WTH-2
Version 1.8.000 - 20170915
----------------------------------------------------------------------------------------
Version:
Application: 1.8.000
Bootloader: 1.10.000
Library: 1.20.004
** Related Hardware
* 1434158F, 1434177A
** Bugfix
* Correction in Paging-Module HMOS-Library
Catched erros which could occure after an OTAU update to a newer paging module.
* Correction for the Optimum Start Stop function
After activating the optimum start stop function it is now executed correctly.
** Modification
* Change to Version 1.8.000
Parameter extension for installer solution.
With the help of the new parameter "DISABLE_MSG_TO_AC" all transmissions to the
central address are suppressed. Also to the status receiver address if this is the
same as the central address.
Version 1.6.000 - 20170721
----------------------------------------------------------------------------------------
Version:
Application: 1.6.000
Bootloader: 1.10.000
Library: 1.20.003
** Related Hardware
* 1434158F, 1434177A
** Bugfix
* Expansion for inclusion condition.
If parameter changes have been made to the device before the inclusion, the device
can only be included if a factory reset has been performed on the device before.
* Correction for set point temperature update after weekprogram configuration.
If window open is detected (extern/intern) and during this time a new week program
is transmitted to the device, the device updated the set point temperature after
window close by using the new week program set point temperature.
* Correction when changing from auto mode to manu mode.
When changing from auto mode to manu mode and boost is active, boost is abort.
* The date and time are cyclically synchronized with the access point.
In order that date and time are be synchron in system, the data is retrieved every
6 hours at Access point.
* Extension for the Quick Veto Function.
If the quick veto function is active, the remaining time is transferred in the
status telegram.
* Behavior after aborting the factory reset.
If the factory reset is aborted or not executed until the end, the device performs
a reboot after the termination or after the timeout.
* Abort of Quick Veto by "Duration = 0".
If Quick Veto is active, Quick Veto can be aborted by the radio command
"Duration = 0". The device answers the radio telegram with an "Ack".
** Modification
* Change to Version 1.6.000
- shartelt
- Beiträge: 7421
- Registriert: 14.01.2015, 14:59
- System: Alternative CCU (auf Basis OCCU)
- Hat sich bedankt: 524 Mal
- Danksagung erhalten: 753 Mal
Re: HmIP-WTH-2 Firmware 1.8
verdammt...habe mich erst getraut vor 2 Wochen das Update zu fahren auf 1.4.4.
jetzt wieder die Neuanlerngeschichte :/
jetzt wieder die Neuanlerngeschichte :/
Re: HmIP-WTH-2 Firmware 1.8
Wie genau geht ihr denn vor? Update, Gerät löschen, Verknüpfungen löschen, Gerät neu anlernen, Verknüpfungen neu erstellen? Gruß
Gesendet von iPhone mit Tapatalk
Gesendet von iPhone mit Tapatalk
-
- Beiträge: 106
- Registriert: 24.01.2018, 08:08
- Hat sich bedankt: 7 Mal
Re: HmIP-WTH-2 Firmware 1.8
Muss man überhaupt ablernen und neu anlernen? Normalerweise steht das doch in der Changelog-Datei wenn dieser Schritt notwendig sein sollte.
- deimos
- Beiträge: 5396
- Registriert: 20.06.2017, 10:38
- System: Alternative CCU (auf Basis OCCU)
- Wohnort: Leimersheim
- Hat sich bedankt: 121 Mal
- Danksagung erhalten: 957 Mal
- Kontaktdaten:
Re: HmIP-WTH-2 Firmware 1.8
Hi,
Viele Grüße
Alex
Im Changelog steht es nicht drin. Ich habe aber grade beim ersten Gerät das Update durchgeführt und danach die CCU neu gestartet. Leider das befürchtete Verhalten, leider inkl. dem Problem, dass sich die Geräte nicht richtig ablernen lassen.Enterhaken hat geschrieben:Muss man überhaupt ablernen und neu anlernen? Normalerweise steht das doch in der Changelog-Datei wenn dieser Schritt notwendig sein sollte.
Viele Grüße
Alex
- deimos
- Beiträge: 5396
- Registriert: 20.06.2017, 10:38
- System: Alternative CCU (auf Basis OCCU)
- Wohnort: Leimersheim
- Hat sich bedankt: 121 Mal
- Danksagung erhalten: 957 Mal
- Kontaktdaten:
Re: HmIP-WTH-2 Firmware 1.8
Hi,
löschen auf die harte Tour (Config editieren). Und für die verbleibenden läuft es halt auf Update einspielen, Direktverknüpfungen löschen, Gerät ablernen, frisch anlernen und frisch konfigurieren raus.
Viele Grüße
Alex
löschen auf die harte Tour (Config editieren). Und für die verbleibenden läuft es halt auf Update einspielen, Direktverknüpfungen löschen, Gerät ablernen, frisch anlernen und frisch konfigurieren raus.
Viele Grüße
Alex
- shartelt
- Beiträge: 7421
- Registriert: 14.01.2015, 14:59
- System: Alternative CCU (auf Basis OCCU)
- Hat sich bedankt: 524 Mal
- Danksagung erhalten: 753 Mal
Re: HmIP-WTH-2 Firmware 1.8
aktuell war 1.4.4 und dazwischen gabs noch die 1.6, welche einige Änderungen hatte...
Tante Edit(h) sagt: für CCU Nutzer.
Tante Edit(h) sagt: für CCU Nutzer.
Re: HmIP-WTH-2 Firmware 1.8
JEP
Odyssee vom feinsten. 8WTH-2 abgelernt, 2xFAL abgelernt 1xMulti I/O abgelernt, und dann das ganze neu drauf.
Leider hat es mit nur ablernen und Backup einspielen nicht Funktioniert, nach dem Backup einspielen War die CCU verdammt träge und langsam.
Hatte somit nette 2 Stunden mit dem Backup Rumgedoktert um danach nochmal 2 Stunden alles neu zu Konfigurieren
Naja war ja bei 1.4 und 1.6 nix anders
Auf alle Fälle ging die Firm innerhalb 15 Stunden auf alle WTH2, incl 4 mal DutyCycle Reset
Odyssee vom feinsten. 8WTH-2 abgelernt, 2xFAL abgelernt 1xMulti I/O abgelernt, und dann das ganze neu drauf.
Leider hat es mit nur ablernen und Backup einspielen nicht Funktioniert, nach dem Backup einspielen War die CCU verdammt träge und langsam.
Hatte somit nette 2 Stunden mit dem Backup Rumgedoktert um danach nochmal 2 Stunden alles neu zu Konfigurieren
Naja war ja bei 1.4 und 1.6 nix anders
Auf alle Fälle ging die Firm innerhalb 15 Stunden auf alle WTH2, incl 4 mal DutyCycle Reset