keine Lese-/Löschrechte auf USB-Stick in RaspberryMatic

[jmaus]

Wie Erwin schrieb, sind die Zuweisungen tatsächlich in usbmount.conf:

Das kann nicht der Grund für deine Probleme sein. Hast du denn schon einen anderen USB Stick probiert oder diesen neu als FAT32 Stick formatiert? Für mich sieht das danach aus, dass das Fikesystem dieses Sticks ggf defekt ist und deshalb von Linux kerbel auf read-only gestellt wird. Schau dir auch mal die Ausgaben des "dmesg" kommandos an.

[PeterM]

Hallo Jens,

den Stick habe ich natürlich schon mehrfach gewechselt und die verschiedenen Formatierungen ausprobiert.
Auffällig ist, dass FileZilla schreiben/lesen/löschen/neuanlegen kann. Während Homeputer nur schreiben/neuanlegen kann.
dmesg bringt folgendes:

Code: Alles auswählen

Using username "root".
# dmesg
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.14.79 (damato@bilbo) (gcc version 7.3.0 (Buildroot 2018.11.1-01687-gf5c92f64-dirty)) #1 SMP PREEMPT Thu Dec 20 14:58:03 CET 2018
[    0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c5383d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Raspberry Pi 3 Model B Rev 1.2
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] cma: Reserved 8 MiB at 0x3d800000
[    0.000000] On node 0 totalpages: 253952
[    0.000000] free_area_init_node: node 0, pgdat 80c7eac0, node_mem_map bcf3c000
[    0.000000]   Normal zone: 2232 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 253952 pages, LIFO batch:31
[    0.000000] percpu: Embedded 17 pages/cpu @bcee4000 s39052 r8192 d22388 u69632
[    0.000000] pcpu-alloc: s39052 r8192 d22388 u69632 alloc=17*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 251720
[    0.000000] Kernel command line: dwc_otg.lpm_enable=0 sdhci_bcm2708.enable_llm=0 console=tty2 kgdboc=tty2 scandelay=5 root=PARTUUID=deedbeef-02 ro noswap rootfstype=ext4 elevator=deadline fsck.repair=yes lapic rootwait rootdelay=5 consoleblank=0 logo.nologo quiet loglevel=0 usb-storage.quirks=  8250.nr_uarts=1 bcm2708_fb.fbwidth=640 bcm2708_fb.fbheight=480 bcm2708_fb.fbswap=1 vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000  empty
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 984916K/1015808K available (7168K kernel code, 549K rwdata, 2056K rodata, 1024K init, 697K bss, 22700K reserved, 8192K cma-reserved)
[    0.000000] Virtual kernel memory layout:
                   vector  : 0xffff0000 - 0xffff1000   (   4 kB)
                   fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
                   vmalloc : 0xbe800000 - 0xff800000   (1040 MB)
                   lowmem  : 0x80000000 - 0xbe000000   ( 992 MB)
                   modules : 0x7f000000 - 0x80000000   (  16 MB)
                     .text : 0x80008000 - 0x80800000   (8160 kB)
                     .init : 0x80b00000 - 0x80c00000   (1024 kB)
                     .data : 0x80c00000 - 0x80c89508   ( 550 kB)
                      .bss : 0x80c9103c - 0x80d3f7a0   ( 698 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] ftrace: allocating 24897 entries in 74 pages
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Tasks RCU enabled.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] arch_timer: cp15 timer(s) running at 19.20MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[    0.000007] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[    0.000018] Switching to timer-based delay loop, resolution 52ns
[    0.000297] Console: colour dummy device 80x30
[    0.000315] console [tty2] enabled
[    0.000341] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[    0.000358] pid_max: default: 32768 minimum: 301
[    0.000662] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000678] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.001645] Disabling memory control group subsystem
[    0.001724] CPU: Testing write buffer coherency: ok
[    0.002161] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.040050] Setting up static identity map for 0x100000 - 0x10003c
[    0.060041] Hierarchical SRCU implementation.
[    0.100110] smp: Bringing up secondary CPUs ...
[    0.170581] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.240640] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.310766] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.310912] smp: Brought up 1 node, 4 CPUs
[    0.310925] SMP: Total of 4 processors activated (153.60 BogoMIPS).
[    0.310931] CPU: All CPU(s) started in HYP mode.
[    0.310936] CPU: Virtualization extensions available.
[    0.311798] devtmpfs: initialized
[    0.323433] random: get_random_u32 called from bucket_table_alloc+0x120/0x24c with crng_init=0
[    0.324429] VFP support v0.3: implementor 41 architecture 3 part 40 variant 3 rev 4
[    0.324681] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.324700] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.325290] pinctrl core: initialized pinctrl subsystem
[    0.326137] NET: Registered protocol family 16
[    0.342648] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[    0.348142] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.348150] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.350343] bcm2835-mbox 3f00b880.mailbox: mailbox enabled
[    0.385454] bcm2835-dma 3f007000.dma: DMA legacy API manager at be813000, dmachans=0x1
[    0.387027] SCSI subsystem initialized
[    0.387276] usbcore: registered new interface driver usbfs
[    0.387333] usbcore: registered new interface driver hub
[    0.387430] usbcore: registered new device driver usb
[    0.390718] raspberrypi-firmware soc:firmware: Attached to firmware from 2018-11-04 16:31
[    0.392427] clocksource: Switched to clocksource arch_sys_counter
[    0.483148] VFS: Disk quotas dquot_6.6.0
[    0.483233] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.483465] FS-Cache: Loaded
[    0.483673] CacheFiles: Loaded
[    0.492737] NET: Registered protocol family 2
[    0.493483] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.493594] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.493781] TCP: Hash tables configured (established 8192 bind 8192)
[    0.493919] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.493964] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.494215] NET: Registered protocol family 1
[    0.494831] RPC: Registered named UNIX socket transport module.
[    0.494838] RPC: Registered udp transport module.
[    0.494844] RPC: Registered tcp transport module.
[    0.494850] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.496774] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 7 counters available
[    0.500011] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[    0.508903] FS-Cache: Netfs 'nfs' registered for caching
[    0.509579] NFS: Registering the id_resolver key type
[    0.509613] Key type id_resolver registered
[    0.509620] Key type id_legacy registered
[    0.511784] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[    0.511925] io scheduler noop registered
[    0.511933] io scheduler deadline registered (default)
[    0.512103] io scheduler cfq registered
[    0.512111] io scheduler mq-deadline registered
[    0.512118] io scheduler kyber registered
[    0.515403] BCM2708FB: allocated DMA memory fd910000
[    0.515434] BCM2708FB: allocated DMA channel 0 @ be813000
[    0.520808] Console: switching to colour frame buffer device 80x30
[    0.526253] Serial: 8250/16550 driver, 1 ports, IRQ sharing enabled
[    0.527929] bcm2835-rng 3f104000.rng: hwrng registered
[    0.528090] vc-mem: phys_addr:0x00000000 mem_base=0x3ec00000 mem_size:0x40000000(1024 MiB)
[    0.528578] vc-sm: Videocore shared memory driver
[    0.528892] gpiomem-bcm2835 3f200000.gpiomem: Initialised: Registers at 0x3f200000
[    0.539383] brd: module loaded
[    0.549340] loop: module loaded
[    0.549354] Loading iSCSI transport class v2.0-870.
[    0.550069] libphy: Fixed MDIO Bus: probed
[    0.550179] usbcore: registered new interface driver lan78xx
[    0.550239] usbcore: registered new interface driver smsc95xx
[    0.550255] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[    0.550549] dwc_otg 3f980000.usb: base=0xf0980000
[    0.750751] Core Release: 2.80a
[    0.750760] Setting default values for core params
[    0.750786] Finished setting default values for core params
[    0.951052] Using Buffer DMA mode
[    0.951059] Periodic Transfer Interrupt Enhancement - disabled
[    0.951065] Multiprocessor Interrupt Enhancement - disabled
[    0.951073] OTG VER PARAM: 0, OTG VER FLAG: 0
[    0.951083] Dedicated Tx FIFOs mode
[    0.951447] WARN::dwc_otg_hcd_init:1046: FIQ DMA bounce buffers: virt = 0xbd904000 dma = 0xfd904000 len=9024
[    0.951473] FIQ FSM acceleration enabled for :
               Non-periodic Split Transactions
               Periodic Split Transactions
               High-Speed Isochronous Endpoints
               Interrupt/Control Split Transaction hack enabled
[    0.951481] dwc_otg: Microframe scheduler enabled
[    0.951538] WARN::hcd_init_fiq:459: FIQ on core 1 at 0x805df6b4
[    0.951550] WARN::hcd_init_fiq:460: FIQ ASM at 0x805dfa10 length 36
[    0.951563] WARN::hcd_init_fiq:486: MPHI regs_base at 0xf0006000
[    0.951623] dwc_otg 3f980000.usb: DWC OTG Controller
[    0.951654] dwc_otg 3f980000.usb: new USB bus registered, assigned bus number 1
[    0.951687] dwc_otg 3f980000.usb: irq 62, io mem 0x00000000
[    0.951735] Init: Port Power? op_state=1
[    0.951741] Init: Power Port (0)
[    0.952003] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.952015] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.952025] usb usb1: Product: DWC OTG Controller
[    0.952034] usb usb1: Manufacturer: Linux 4.14.79 dwc_otg_hcd
[    0.952043] usb usb1: SerialNumber: 3f980000.usb
[    0.952703] hub 1-0:1.0: USB hub found
[    0.952748] hub 1-0:1.0: 1 port detected
[    0.953323] dwc_otg: FIQ enabled
[    0.953330] dwc_otg: NAK holdoff enabled
[    0.953336] dwc_otg: FIQ split-transaction FSM enabled
[    0.953347] Module dwc_common_port init
[    0.953600] usbcore: registered new interface driver usb-storage
[    0.953779] mousedev: PS/2 mouse device common for all mice
[    0.953876] IR NEC protocol handler initialized
[    0.953882] IR RC5(x/sz) protocol handler initialized
[    0.953888] IR RC6 protocol handler initialized
[    0.953894] IR JVC protocol handler initialized
[    0.953900] IR Sony protocol handler initialized
[    0.953906] IR SANYO protocol handler initialized
[    0.953912] IR Sharp protocol handler initialized
[    0.953918] IR MCE Keyboard/mouse protocol handler initialized
[    0.953924] IR XMP protocol handler initialized
[    0.954870] bcm2835-wdt 3f100000.watchdog: Broadcom BCM2835 watchdog timer
[    0.955147] bcm2835-cpufreq: min=600000 max=1200000
[    0.955599] sdhci: Secure Digital Host Controller Interface driver
[    0.955605] sdhci: Copyright(c) Pierre Ossman
[    0.955989] mmc-bcm2835 3f300000.mmc: could not get clk, deferring probe
[    0.956345] sdhost-bcm2835 3f202000.mmc: could not get clk, deferring probe
[    0.956461] sdhci-pltfm: SDHCI platform and OF driver helper
[    0.959483] ledtrig-cpu: registered to indicate activity on CPUs
[    0.959533] hidraw: raw HID events driver (C) Jiri Kosina
[    0.959608] usbcore: registered new interface driver usbhid
[    0.959611] usbhid: USB HID core driver
[    0.960031] vchiq: vchiq_init_state: slot_zero = bd980000, is_master = 0
[    0.961271] [vc_sm_connected_init]: start
[    0.969742] [vc_sm_connected_init]: end - returning 0
[    0.970132] ip_tables: (C) 2000-2006 Netfilter Core Team
[    0.970336] Initializing XFRM netlink socket
[    0.970353] NET: Registered protocol family 17
[    0.970412] Key type dns_resolver registered
[    0.970785] Registering SWP/SWPB emulation handler
[    0.971119] registered taskstats version 1
[    0.975829] 3f215040.serial: ttyS0 at MMIO 0x0 (irq = 166, base_baud = 31250000) is a 16550
[    0.976374] mmc-bcm2835 3f300000.mmc: mmc_debug:0 mmc_debug2:0
[    0.976379] mmc-bcm2835 3f300000.mmc: DMA channel allocated
[    1.033022] sdhost: log_buf @ bd907000 (fd907000)
[    1.066392] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[    1.067913] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    1.069433] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    1.072163] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[    1.112451] mmc0: sdhost-bcm2835 loaded - DMA enabled (>1)
[    1.113866] of_cfs_init
[    1.113974] of_cfs_init: OK
[    1.132953] Waiting 5 sec before mounting root device...
[    1.142225] random: fast init done
[    1.172561] Indeed it is in host mode hprt0 = 00021501
[    1.189275] mmc0: host does not support reading read-only switch, assuming write-enable
[    1.191870] mmc0: new high speed SDHC card at address 59b4
[    1.192180] mmcblk0: mmc0:59b4 NCard 14.9 GiB
[    1.194260] mmc1: new high speed SDIO card at address 0001
[    1.238208]  mmcblk0: p1 p2 p3
[    1.382464] usb 1-1: new high-speed USB device number 2 using dwc_otg
[    1.382568] Indeed it is in host mode hprt0 = 00001101
[    1.622717] usb 1-1: New USB device found, idVendor=0424, idProduct=9514
[    1.622729] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.623312] hub 1-1:1.0: USB hub found
[    1.623403] hub 1-1:1.0: 5 ports detected
[    1.942460] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[    2.072666] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
[    2.072678] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    2.075221] smsc95xx v1.0.6
[    2.165500] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-3f980000.usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:33:a9:37
[    3.162464] usb 1-1.2: new high-speed USB device number 4 using dwc_otg
[    3.299435] usb 1-1.2: New USB device found, idVendor=8564, idProduct=1000
[    3.299448] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    3.299458] usb 1-1.2: Product: Mass Storage Device
[    3.299467] usb 1-1.2: Manufacturer: JetFlash
[    3.299476] usb 1-1.2: SerialNumber: Y5SWHGWE
[    3.300089] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[    3.300647] scsi host0: usb-storage 1-1.2:1.0
[    4.324381] scsi 0:0:0:0: Direct-Access     JetFlash Transcend 16GB   8.07 PQ: 0 ANSI: 2
[    4.326284] sd 0:0:0:0: [sda] 31375360 512-byte logical blocks: (16.1 GB/15.0 GiB)
[    4.326521] sd 0:0:0:0: [sda] Write Protect is off
[    4.326534] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
[    4.326771] sd 0:0:0:0: [sda] No Caching mode page found
[    4.326782] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    4.330069]  sda: sda1
[    4.331671] sd 0:0:0:0: [sda] Attached SCSI removable disk
[    6.174816] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    6.174870] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[    6.181311] devtmpfs: mounted
[    6.185250] Freeing unused kernel memory: 1024K
[    6.870750] EXT4-fs: Warning: mounting with data=journal disables delayed allocation and O_DIRECT support!
[    6.881330] EXT4-fs (mmcblk0p3): mounted filesystem with journalled data mode. Opts: data=journal
[    7.034257] i2c /dev entries driver
[    7.070849] rtc_rx8130: loading out-of-tree module taints kernel.
[    7.076682] rtc-ds1307 1-0032: registered as rtc0
[    7.076758] i2c i2c-1: new_device: Instantiated device rx8130 at 0x32
[    7.501165] tun: Universal TUN/TAP device driver, 1.6
[    7.638132] udevd[195]: starting version 3.2.5
[    7.640748] random: udevd: uninitialized urandom read (16 bytes read)
[    7.643134] random: udevd: uninitialized urandom read (16 bytes read)
[    7.643294] random: udevd: uninitialized urandom read (16 bytes read)
[    7.688250] udevd[199]: starting eudev-3.2.5
[    7.771659] pl011_raw_uart 3f201000.serial: No reset pin configured in device tree
[    7.771752] pl011_raw_uart 3f201000.serial: Initialized pl011 device; mapbase=0x3f201000; irq=87; clockrate=47999625
[    7.908373] pinctrl-bcm2835 3f200000.gpio: pin gpio18 already requested by leds; cannot claim for 3f203000.i2s
[    7.908385] pinctrl-bcm2835 3f200000.gpio: pin-18 (3f203000.i2s) status -22
[    7.908392] pinctrl-bcm2835 3f200000.gpio: could not request pin 18 (gpio18) from group gpio18  on device pinctrl-bcm2835
[    7.908397] bcm2835-i2s 3f203000.i2s: Error applying setting, reverse things back
[    7.908417] bcm2835-i2s: probe of 3f203000.i2s failed with error -22
[    7.947684] brcmfmac: F1 signature read @0x18000000=0x1541a9a6
[    7.953309] brcmfmac: brcmf_fw_map_chip_to_name: using brcm/brcmfmac43430-sdio.bin for chip 0x00a9a6(43430) rev 0x000001
[    7.953481] usbcore: registered new interface driver brcmfmac
[    8.205214] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[    8.235879] random: crng init done
[    8.235892] random: 4 urandom warning(s) missed due to ratelimiting
[    8.248527] brcmfmac: brcmf_c_preinit_dcmds: Firmware version = wl0: Oct 23 2017 03:55:53 version 7.45.98.38 (r674442 CY) FWID 01-e58d219f
[    8.249270] brcmfmac: brcmf_c_preinit_dcmds: CLM version = API: 12.2 Data: 7.11.15 Compiler: 1.24.2 ClmImport: 1.24.1 Creation: 2014-05-26 10:53:55 Inc Data: 9.10.39 Inc Compiler: 1.29.4 Inc ClmImport: 1.36.3 Creation: 2017-10-23 03:47:14
[   21.264386] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[   33.335154] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[   33.407454] brcmfmac: power management disabled
[   41.875429] NET: Registered protocol family 10
[   41.880094] Segment Routing with IPv6
[   42.216198] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[   42.664070] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   44.344901] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[   44.345345] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   54.147845] eq3loop: created slave mmd_hmip
[   54.149098] eq3loop: created slave mmd_bidcos
[   56.337601] eq3loop: eq3loop_open_slave() mmd_bidcos
[   69.256308] eq3loop: eq3loop_open_slave() mmd_hmip
[   69.256684] eq3loop: eq3loop_close_slave() mmd_hmip
[   69.260358] eq3loop: eq3loop_open_slave() mmd_hmip
[   69.260586] eq3loop: eq3loop_close_slave() mmd_hmip
[   69.272619] eq3loop: eq3loop_open_slave() mmd_hmip
[694613.814352] usb 1-1.2: USB disconnect, device number 4
[694777.436133] usb 1-1.2: new high-speed USB device number 5 using dwc_otg
[694777.573178] usb 1-1.2: New USB device found, idVendor=8564, idProduct=1000
[694777.573192] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[694777.573202] usb 1-1.2: Product: Mass Storage Device
[694777.573212] usb 1-1.2: Manufacturer: JetFlash
[694777.573221] usb 1-1.2: SerialNumber: Y5SWHGWE
[694777.574002] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[694777.574768] scsi host1: usb-storage 1-1.2:1.0
[694778.618160] scsi 1:0:0:0: Direct-Access     JetFlash Transcend 16GB   8.07 PQ: 0 ANSI: 2
[694778.620345] sd 1:0:0:0: [sdb] 31375360 512-byte logical blocks: (16.1 GB/15.0 GiB)
[694778.620601] sd 1:0:0:0: [sdb] Write Protect is off
[694778.620615] sd 1:0:0:0: [sdb] Mode Sense: 03 00 00 00
[694778.620860] sd 1:0:0:0: [sdb] No Caching mode page found
[694778.620872] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[694778.626630]  sdb: sdb1
[694778.630831] sd 1:0:0:0: [sdb] Attached SCSI removable disk
[694824.599937] blk_partition_remap: fail for partition 1
[694824.599962] blk_partition_remap: fail for partition 1
...
[694824.600163] blk_partition_remap: fail for partition 1
[694824.600178] FAT-fs (sda1): Directory bread(block 32768) failed
[694824.600190] blk_partition_remap: fail for partition 1
[694824.600200] FAT-fs (sda1): Directory bread(block 32769) failed
[694824.600212] blk_partition_remap: fail for partition 1
[694824.600222] FAT-fs (sda1): Directory bread(block 32770) failed
[694824.600233] blk_partition_remap: fail for partition 1
[694824.600243] FAT-fs (sda1): Directory bread(block 32771) failed
[694824.600255] blk_partition_remap: fail for partition 1
[694824.600265] FAT-fs (sda1): Directory bread(block 32772) failed
[694824.600277] blk_partition_remap: fail for partition 1
[694824.600287] FAT-fs (sda1): Directory bread(block 32773) failed
[694824.600299] blk_partition_remap: fail for partition 1
[694824.600308] FAT-fs (sda1): Directory bread(block 32774) failed
[694824.600320] blk_partition_remap: fail for partition 1
[694824.600329] FAT-fs (sda1): Directory bread(block 32775) failed
[694824.600341] blk_partition_remap: fail for partition 1
[694824.600350] FAT-fs (sda1): Directory bread(block 32776) failed
[694824.600362] blk_partition_remap: fail for partition 1
[694824.600371] FAT-fs (sda1): Directory bread(block 32777) failed
[694824.600384] blk_partition_remap: fail for partition 1
[694824.600398] blk_partition_remap: fail for partition 1
[694824.600411] blk_partition_remap: fail for partition 1
[694824.600424] blk_partition_remap: fail for partition 1
[694824.600438] blk_partition_remap: fail for partition 1
[694824.600451] blk_partition_remap: fail for partition 1
...
[694824.614691] blk_partition_remap: fail for partition 1
[694824.614705] blk_partition_remap: fail for partition 1
[707649.334406] usb 1-1.2: USB disconnect, device number 5
[707649.402971] blk_partition_remap: fail for partition 1
[707649.402993] FAT-fs (sdb1): unable to read boot sector to mark fs as dirty
[707668.062836] usb 1-1.5: new high-speed USB device number 6 using dwc_otg
[707668.199851] usb 1-1.5: New USB device found, idVendor=8564, idProduct=1000
[707668.199865] usb 1-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[707668.199875] usb 1-1.5: Product: Mass Storage Device
[707668.199885] usb 1-1.5: Manufacturer: JetFlash
[707668.199894] usb 1-1.5: SerialNumber: Y5SWHGWE
[707668.201175] usb-storage 1-1.5:1.0: USB Mass Storage device detected
[707668.201752] scsi host0: usb-storage 1-1.5:1.0
[707669.204692] scsi 0:0:0:0: Direct-Access     JetFlash Transcend 16GB   8.07 PQ: 0 ANSI: 2
[707669.207894] sd 0:0:0:0: [sda] 31375360 512-byte logical blocks: (16.1 GB/15.0 GiB)
[707669.208172] sd 0:0:0:0: [sda] Write Protect is off
[707669.208186] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
[707669.208433] sd 0:0:0:0: [sda] No Caching mode page found
[707669.208444] sd 0:0:0:0: [sda] Assuming drive cache: write through
[707669.212151]  sda: sda1
[707669.214968] sd 0:0:0:0: [sda] Attached SCSI removable disk
[707669.488087] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[708267.318442] usb 1-1.5: USB disconnect, device number 6
[708313.184242] usb 1-1.2: new high-speed USB device number 7 using dwc_otg
[708313.321267] usb 1-1.2: New USB device found, idVendor=8564, idProduct=1000
[708313.321282] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[708313.321292] usb 1-1.2: Product: Mass Storage Device
[708313.321304] usb 1-1.2: Manufacturer: JetFlash
[708313.321314] usb 1-1.2: SerialNumber: Y5SWHGWE
[708313.322662] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[708313.323238] scsi host0: usb-storage 1-1.2:1.0
[708314.326124] scsi 0:0:0:0: Direct-Access     JetFlash Transcend 16GB   8.07 PQ: 0 ANSI: 2
[708314.329582] sd 0:0:0:0: [sda] 31375360 512-byte logical blocks: (16.1 GB/15.0 GiB)
[708314.329824] sd 0:0:0:0: [sda] Write Protect is off
[708314.329837] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
[708314.330076] sd 0:0:0:0: [sda] No Caching mode page found
[708314.330088] sd 0:0:0:0: [sda] Assuming drive cache: write through
[708314.333886]  sda: sda1
[708314.336853] sd 0:0:0:0: [sda] Attached SCSI removable disk
[708314.606023] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[955777.654990] EXT4-fs (mmcblk0p2): re-mounted. Opts: data=ordered
[955800.824765] EXT4-fs (mmcblk0p2): re-mounted. Opts: data=ordered
[957372.471143] usb 1-1.2: USB disconnect, device number 7
[957422.177471] usb 1-1.2: new high-speed USB device number 8 using dwc_otg
[957422.314515] usb 1-1.2: New USB device found, idVendor=8564, idProduct=1000
[957422.314530] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[957422.314541] usb 1-1.2: Product: Mass Storage Device
[957422.314550] usb 1-1.2: Manufacturer: JetFlash
[957422.314559] usb 1-1.2: SerialNumber: Y5SWHGWE
[957422.315363] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[957422.318492] scsi host0: usb-storage 1-1.2:1.0
[957423.349361] scsi 0:0:0:0: Direct-Access     JetFlash Transcend 16GB   8.07 PQ: 0 ANSI: 2
[957423.354134] sd 0:0:0:0: [sda] 31375360 512-byte logical blocks: (16.1 GB/15.0 GiB)
[957423.354378] sd 0:0:0:0: [sda] Write Protect is off
[957423.354391] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
[957423.354627] sd 0:0:0:0: [sda] No Caching mode page found
[957423.354639] sd 0:0:0:0: [sda] Assuming drive cache: write through
[957423.360163]  sda: sda1
[957423.362201] sd 0:0:0:0: [sda] Attached SCSI removable disk
[957423.616884] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
#

Ich kann leider damit nichts anfangen...

Viele Grüße,
Peter

[jmaus]

Auffällig ist, dass FileZilla schreiben/lesen/löschen/neuanlegen kann. Während Homeputer nur schreiben/neuanlegen kann.

Na wenn das so ist, dann würde ich den Fehler mal bei Homeputer suchen und den Autor davon kontaktieren. Es kann ja dann nicht an RaspberryMatic selbst liegen.

[PeterM]

Moin Jens,

Na wenn das so ist, dann würde ich den Fehler mal bei Homeputer suchen und den Autor davon kontaktieren. Es kann ja dann nicht an RaspberryMatic selbst liegen.

das ist ja eben das Problem. Wir hatten natürlich zuerst H. Krapoth informiert, aber er hat uns versichert, dass es für RaspberryMatic keine anderen Routinen gibt. Das Problem also NICHT auf seiner Seite liegt.

Ich wollte hier auch nicht darauf hinweisen, dass in RaspberryMatic ein Fehler vorliegt - es kann sich ja auch um irgendein anderes Problem handeln.
Ich dachte nur, im Forum gibt es genügend Mitstreiter die wesentlich mehr Ahnung von Linux haben als ich und die mir einen Hinweis liefern, was ich testen könnte.

Gruß,
Peter

[NickHM]

Hallo

auf Grund der Diskussion hier habe ich mal auf meiner CCU3 nachgesehen.

Ich habe für die 30 tage des Monats pro Tag ein Logfile. Wenn der aktuelle Tag des Monats dem Tag des Vormonats entspricht, wird das alte Logfile gelöscht und eine neue Datei geschrieben. So jedenfalls bisher.

Jetzt habe ich mal nachgesehen und fest gestellt, dass auch auf meiner CCU3 die neuen Textzeilen an die bestehende Datei angehängt werden. Die Textdatei wird also länger und nicht im neuen Monat gelöscht.

Es ist also ein Homeputer Problem und kein spezielles RasPi Problem.

RK hatte mir auch geschrieben, dass in der Weboberfläche "Workfiles" die Buttons "Datei umbenennen" "Datei löschen" derzeit nicht verfügbar sind, weil es mit der CCU3 nicht funktioniert. Kommt aber wieder.
Ob das mit dem o.g. Problem zusammenhängt, weiss ich nicht.

Wir sollten das im HP Unterforum weiter besprechen.

[PeterM]

Dann hat sich H. Krapoth wohl doch vertan...
Warten wir auf die Korrektur.

[NickHM]

Dann hat sich H. Krapoth wohl doch vertan...
Warten wir auf die Korrektur.

Es gibt (neue) Versionen vom 12.Jan 2019
Die habe ich jetzt mal installiert.
Es gab auch einen Fehler für den neuen HMIP Heizungsthermostaten.
mal sehen, was sich verbessert hat.

Ansonsten müsste RK das ggf. noch mal gesagt bekommen, dass "Löschedatei" nicht geht ?

[PeterM]

Hallo NickHM,

vielen Dank für deinen Hinweis.
Wie hier viewtopic.php?f=28&t=48198#p483229 bereits von Günter (Daimler) und Familienvater beschrieben muss man nur die Pfadangaben in homeputer weglassen, dann klappt sowohl LESEWERTEDATEI, als auch LÖSCHEDATEI mittels homeputer.

Und ja, wie du in dem gleichen Thread auch erwähnt hast, halte ich dies auch für einen Fehler, da in der CCU2-Umgebung das Problem nicht auftritt.

Ob der "Fehler" allerdings erst durch das Einspielen der neuen homeputer-Software behoben wurde kann ich nicht sagen, da ich einen entsprechenden Test vorher nicht gemacht hatte (und jetzt auch keine Lust habe, das ganze wieder zurückzudrehen).

Vielen Dank an alle die bei der Lösungsfindung beigetragen haben.

Viele Grüße,
Peter

[NickHM]

Wie hier viewtopic.php?f=28&t=48198#p483229 bereits von Günter (Daimler) und Familienvater beschrieben muss man nur die Pfadangaben in homeputer weglassen, dann klappt sowohl LESEWERTEDATEI, als auch LÖSCHEDATEI mittels homeputer.

Hallo

den Pfad weg zu lassen hilft mir leider wenig, da die entsprechenden Dateien in einem Unterverzeichnis auf dem USB Stick liegen.

BTW mit der Version vom 12.1. wird jetzt für den HMIP-Heizkörperthermostat-C die Ventilstellung richtig angezeigt.

[PeterM]

Hi NickHM,

da habe ich mich nicht richtig ausgedrückt!

EDIT 22.01.2019 17:25 >>>>>>
Es muss nur der Teil des Pfades weggelassen werden, der bereits unter "Einstellungen" -> "Verzeichnisse" eingetragen ist.
Es muss nur der Teil des Pfades weggelassen werden, der bereits unter "Konfigurieren" -> "Hardware" -> "Zentrale" eingetragen ist.
EDIT 22.01.2019 17:25 <<<<<<
Das ist in der Regel /Media/usb0. Wenn darunter ein Verzeichnis liegt, dann muss dies natürlich angegeben werden:
PfadDatei:= "/Media/Usb0/LOG/Log_" + Monatstag -> dies ist falsch!
EDIT 22.01.2019 17:25 >>>>>>
PfadDatei:= "/LOG/Log_" + Monatstag -> RICHTIG
PfadDatei:= "LOG/Log_" + Monatstag -> RICHTIG (vielen Dank an NickHM für die Berichtigung)
EDIT 22.01.2019 17:25 <<<<<<

Zumindest hat dies bei uns geholfen.

Viele Grüße,
Peter