LanGW + monit/ watchdog

Einrichtung, Nutzung und Hilfe zu RaspberryMatic (OCCU auf Raspberry Pi)

Moderatoren: jmaus, Co-Administratoren

Antworten
virgin
Beiträge: 636
Registriert: 09.01.2013, 18:36
Wohnort: Leichlingen
Hat sich bedankt: 124 Mal
Danksagung erhalten: 5 Mal
Kontaktdaten:

LanGW + monit/ watchdog

Beitrag von virgin » 09.05.2022, 09:08

Meine drei FLGW‘s zicken auch nach dem letzten Update noch immer herum. Allerdings beobachte ich jetzt eine verändertes Verhalten: bisher fiel mal das eine oder das andere FLGW aus. Leider nicht periodisch, sondern komplett unregelmäßig, so dass ich keine Ursache ermitteln konnte. Mit

Code: Alles auswählen

monit restart rfd
konnte ich den Fehler immer wieder beheben. Obwohl es schon doof ist, da immer wieder manuell eingreifen zu müssen.

JETZT, neu, beobachte ich, dass alle drei FLGW gleichzeitig vom watchdog als nicht verbunden gemeldet werden, und sich dann offensichtlich nach einer gewissen Zeit selbstständig neu verbinden.

Die Alarmmeldungen in der WebUI sind halt unschön. Und wenn es ein Fehler ist, der immerhin einen Alarm erzeugt, dann stimmt ja offenbar irgendwas nicht. Das würde ich gerne beheben!

Code: Alles auswählen

May  9 02:02:58 homematic-ccu2 user.err rfd: (CCU2GWBUEG) CCU2CommController::getDutyCycle(): Could not get DutyCycle from coprocessor.
May  9 02:03:00 homematic-ccu2 user.err rfd: (CCU2GWBUEG) CCU2CommController::getDutyCycle(): Could not get DutyCycle from coprocessor.
May  9 02:03:00 homematic-ccu2 user.err rfd: (CCU2GWGARA) CCU2CommController::getDutyCycle(): Could not get DutyCycle from coprocessor.
May  9 02:03:00 homematic-ccu2 user.err rfd: (CCU2GWKell) CCU2CommController::getDutyCycle(): Could not get DutyCycle from coprocessor.
May  9 02:03:00 homematic-ccu2 user.err watchdog: DutyCycle-CCU2GWBUEG, NAME: 'FLGW_Buegel', TYPE: HMLGW2, CONNECTED: 0, DC: -1 %, CS: -1 %
May  9 02:03:00 homematic-ccu2 user.err watchdog: DutyCycle-CCU2GWGARA, NAME: 'FLGW_GarageNEU', TYPE: HMLGW2, CONNECTED: 0, DC: -1 %, CS: -1 %
May  9 02:03:00 homematic-ccu2 user.err watchdog: DutyCycle-CCU2GWKell, NAME: 'FLGW_Keller', TYPE: HMLGW2, CONNECTED: 0, DC: -1 %, CS: -1 %
May  9 02:03:00 homematic-ccu2 user.err rfd: (CCU2GWGARA) CCU2CommController::getDutyCycle(): Could not get DutyCycle from coprocessor.
May  9 02:03:05 homematic-ccu2 user.err rfd: (CCU2GWKell) CCU2CommController::getDutyCycle(): Could not get DutyCycle from coprocessor.
May  9 02:03:05 homematic-ccu2 user.err rfd: XmlRpcClient error calling event({[methodName:"event",params:{"LinuxNeu:hm-rpc.0:40effdabd6073777a3bb27910fa7a7b4","JEQ0057851:1","VALVE_STATE",0}],[methodName:"event",params:{"LinuxNeu:hm-rpc.0:40effdabd6073777a3bb27910fa7a7b4","JEQ0057851:1","ERROR",0}]}) on http://192.168.0.105:2001/RPC2:
May  9 02:03:05 homematic-ccu2 user.err rfd: XmlRpc transport error
May  9 02:03:06 homematic-ccu2 user.err rfd: UnifiedLanCommController::connect(): Unable to connect.
May  9 02:03:09 homematic-ccu2 user.err rfd: (CCU2GWGARA) CCU2CommController::getDutyCycle(): Could not get DutyCycle from coprocessor.
May  9 02:03:11 homematic-ccu2 user.err rfd: (CCU2GWKell) CCU2CommController::getDutyCycle(): Could not get DutyCycle from coprocessor.
May  9 02:03:11 homematic-ccu2 user.err rfd: (CCU2GWBUEG) CCU2CommController::getDutyCycle(): Could not get DutyCycle from coprocessor.
May  9 02:03:11 homematic-ccu2 user.err rfd: (CCU2GWGARA) CCU2CommController::getDutyCycle(): Could not get DutyCycle from coprocessor.
May  9 02:03:12 homematic-ccu2 user.err rfd: (CCU2GWKell) CCU2CommController::getDutyCycle(): Could not get DutyCycle from coprocessor.
May  9 02:03:12 homematic-ccu2 user.err rfd: (CCU2GWBUEG) CCU2CommController::getDutyCycle(): Could not get DutyCycle from coprocessor.
May  9 02:03:13 homematic-ccu2 user.err rfd: (CCU2GWGARA) CCU2CommController::getDutyCycle(): Could not get DutyCycle from coprocessor.
May  9 02:03:16 homematic-ccu2 user.err rfd: (CCU2GWGARA) CCU2CommController::getDutyCycle(): Could not get DutyCycle from coprocessor.
Hat irgendwer eine Idee, woher das kommt? Was kann ich tun? Danke für Eure Hilfe.
Bernd

Antworten

Zurück zu „RaspberryMatic“