[GELÖST] Raspberrymatic auf Docker fährt nicht mehr hoch - Web-UI nicht zugreifbar

Einrichtung, Nutzung und Hilfe zu RaspberryMatic (OCCU auf Raspberry Pi)

Moderatoren: jmaus, Co-Administratoren

Molt
Beiträge: 18
Registriert: 18.02.2022, 17:02
System: in Planung
Hat sich bedankt: 4 Mal

[GELÖST] Raspberrymatic auf Docker fährt nicht mehr hoch - Web-UI nicht zugreifbar

Beitrag von Molt » 11.04.2023, 11:31

Hi zusammen,

bis vor ein paar Tagen lief alles wunderbar - jetzt fährt der Container nicht hoch und ich bekomme keinen Griff an den Grund.
Ich habe schon etliche Neustarts des Containers, aber auch der Host-Maschine versucht. RFUSB abgezogen und wieder dran gesteckt auch.

Ich hoffe, jemand hat noch eine Idee - danke!



Hier der Auszug von lsusb aus dem Host:

Code: Alles auswählen

/ # sudo lsusb
Bus 001 Device 003: ID 1b1f:c020 eQ-3 Entwicklung GmbH HmIP-RFUSB
Den Eintrag gibts auch im Container:

Code: Alles auswählen

/ # lsusb
Bus 001 Device 003: ID 1b1f:c020
Hier der Auszug von usb-devices auf dem Host

Code: Alles auswählen

/ # sudo usb-devices
T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1b1f ProdID=c020 Rev=01.00
S:  Manufacturer=Silicon Labs
S:  Product=eQ-3 HmIP-RFUSB
S:  SerialNumber=3014F711A000041D89B554F1
C:  #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=hb_rf_usb_2
Hier das Docker Log:

Code: Alles auswählen

/ # docker/homeassistant$ docker logs raspberrymatic
Starting watchdog...
Identifying host system: oci, OK
Initializing RTC Clock: onboard, OK
Running sysctl: OK
Checking for Factory Reset: not required
Checking for Backup Restore: not required
Initializing System: OK
Setup ca-certificates: OK
Starting logging: OK
Populating /dev using udev: done
Init onboard LEDs: init, OK
Starting irqbalance: OK
Saving 256 bits of creditable seed for next boot
Starting iptables: OK
Starting network: eth0: link up, fixed, firewall, inet up, 10.0.10.104, OK
Identifying Homematic RF-Hardware: ....HmRF: HMIP-RFUSB/eQ-3 HmIP-RFUSB@usb-0000:00:1a.0-1.1, HmIP: HMIP-RFUSB/eQ-3 HmIP-RFUSB@usb-0000:00:1a.0-1.1, OK
Updating Homematic RF-Hardware: HMIP-RFUSB: 4.4.18, not necessary, OK
Starting hs485dLoader: disabled
Starting xinetd: OK
Starting eq3configd: OK
Starting lighttpd: OK
Starting ser2net: disabled
Starting ssdpd: OK
Starting NUT services: disabled
Initializing Third-Party Addons: OK
Starting LGWFirmwareUpdate: ...OK
Setting LAN Gateway keys: OK
Starting hs485d: disabled
Starting multimacd: ...........ERROR
Starting rfd: ERROR: /dev/mmd_bidcos missing, no BidCos-RF hardware found
Starting HMIPServer: ERROR: /dev/mmd_hmip missing
Starting ReGaHss: ....................ERROR
Starting CloudMatic: OK
Starting NeoServer: OK
Starting Third-Party Addons: OK
Starting crond: OK
Setup onboard LEDs: booted, OK
Finished Boot: 3.69.6.20230407 (raspmatic_oci_amd64)
Setup onboard LEDs: shutdown, OK
Stopping crond: OK
Stopping Third-Party Addons: OK
Stopping NeoServer: OK
start-stop-daemon: warning: killing process 43400: No such process
Stopping ReGaHss: ..OK
Stopping HMIPServer: OK
Stopping rfd: OK
start-stop-daemon: warning: killing process 47556: No such process
Stopping multimacd: OK
Stopping hs485d: OK
Stopping NUT services: OK
Stopping sshd: OK
start-stop-daemon: warning: killing process 38293: No such process
Stopping ssdpd: FAIL
Shutting down ser2net: OK
Stopping lighttpd: OK
Stopping eq3configd: OK
Stopping xinetd: OK
The futex facility returned an unexpected error code.
Aborted
Stopping network: eth0: link down, OK
Stopping iptables: OK
Seeding 256 bits and crediting
Saving 256 bits of creditable seed for next boot
Stopping irqbalance: OK
Stopping logging: OK
Cleaning up System: OK
Cleaning up RTC Clock: OK
The system is going down NOW!
Sent SIGTERM to all processes
Sent SIGKILL to all processes
Requesting system reboot
Identifying host system: oci, OK
Initializing RTC Clock: onboard, OK
Running sysctl: OK
Checking for Factory Reset: not required
Checking for Backup Restore: not required
Initializing System: OK
Setup ca-certificates: OK
Starting logging: OK
Populating /dev using udev: done
Init onboard LEDs: init, OK
Starting irqbalance: OK
Saving 256 bits of creditable seed for next boot
Starting iptables: OK
Starting network: eth0: link up, fixed, firewall, inet up, 10.0.10.104, OK
Identifying Homematic RF-Hardware: ....HmRF: HMIP-RFUSB/eQ-3 HmIP-RFUSB@usb-0000:00:1a.0-1.1, HmIP: HMIP-RFUSB/eQ-3 HmIP-RFUSB@usb-0000:00:1a.0-1.1, OK
Updating Homematic RF-Hardware: HMIP-RFUSB: 4.4.18, not necessary, OK
Starting hs485dLoader: disabled
Starting xinetd: OK
Starting eq3configd: OK
Starting lighttpd: OK
Starting ser2net: disabled
Starting ssdpd: OK
Starting NUT services: disabled
Initializing Third-Party Addons: OK
Starting LGWFirmwareUpdate: ...OK
Setting LAN Gateway keys: OK
Starting hs485d: disabled
Starting multimacd: ..........ERROR
Starting rfd: ERROR: /dev/mmd_bidcos missing, no BidCos-RF hardware found
Starting HMIPServer: ERROR: /dev/mmd_hmip missing
Starting ReGaHss: ....................ERROR
Starting CloudMatic: OK
Starting NeoServer: OK
Starting Third-Party Addons: OK
Starting crond: OK
Setup onboard LEDs: booted, OK
Finished Boot: 3.69.6.20230407 (raspmatic_oci_amd64)
Setup onboard LEDs: shutdown, OK
Stopping crond: OK
Stopping Third-Party Addons: OK
Stopping NeoServer: OK
start-stop-daemon: warning: killing process 30057: No such process
Stopping ReGaHss: ..OK
Stopping HMIPServer: OK
Stopping rfd: OK
start-stop-daemon: warning: killing process 34062: No such process
Stopping multimacd: OK
Stopping hs485d: OK
Stopping NUT services: OK
Stopping sshd: OK
start-stop-daemon: warning: killing process 40693: No such process
Stopping ssdpd: FAIL
Shutting down ser2net: OK
Stopping lighttpd: OK
Stopping eq3configd: OK
Stopping xinetd: OK
The futex facility returned an unexpected error code.
Aborted (core dumped)
Stopping network: eth0: link down, OK
Stopping iptables: OK
Seeding 256 bits and crediting
Saving 256 bits of creditable seed for next boot
Stopping irqbalance: OK
Stopping logging: OK
Cleaning up System: OK
Cleaning up RTC Clock: OK
The system is going down NOW!
Sent SIGTERM to all processes
Sent SIGKILL to all processes
Requesting system reboot
Starting watchdog...
Identifying host system: oci, OK
Initializing RTC Clock: onboard, OK
Running sysctl: OK
Checking for Factory Reset: not required
Checking for Backup Restore: not required
Initializing System: OK
Setup ca-certificates: OK
Starting logging: OK
Populating /dev using udev: done
Init onboard LEDs: init, OK
Starting irqbalance: OK
Saving 256 bits of creditable seed for next boot
Starting iptables: OK
Starting network: eth0: link up, fixed, firewall, inet up, 10.0.10.104, OK
Identifying Homematic RF-Hardware: ....HmRF: HMIP-RFUSB/eQ-3 HmIP-RFUSB@usb-0000:00:1a.0-1.1, HmIP: HMIP-RFUSB/eQ-3 HmIP-RFUSB@usb-0000:00:1a.0-1.1, OK
Updating Homematic RF-Hardware: HMIP-RFUSB: 4.4.18, not necessary, OK
Starting hs485dLoader: disabled
Starting xinetd: OK
Starting eq3configd: OK
Starting lighttpd: OK
Starting ser2net: disabled
Starting ssdpd: OK
Starting NUT services: disabled
Initializing Third-Party Addons: OK
Starting LGWFirmwareUpdate: ...OK
Setting LAN Gateway keys: OK
Starting hs485d: disabled
Starting multimacd: ...........ERROR
Starting rfd: ERROR: /dev/mmd_bidcos missing, no BidCos-RF hardware found
Starting HMIPServer: ERROR: /dev/mmd_hmip missing
Starting ReGaHss: ....................ERROR
Starting CloudMatic: OK
Starting NeoServer: OK
Starting Third-Party Addons: OK
Starting crond: OK
Setup onboard LEDs: booted, OK
Finished Boot: 3.69.6.20230407 (raspmatic_oci_amd64)
malte@kiwi:/docker/homeassistant$
Hier das Log aus dem Container:

Code: Alles auswählen

/ # tail -f /var/log/messages
Apr 11 11:15:49 raspberrymatic syslog.info syslogd started: BusyBox v1.36.0
Apr 11 11:15:51 raspberrymatic user.info firewall: configuration set
Apr 11 11:15:55 raspberrymatic daemon.err xinetd[1869]: Unable to read included directory: /etc/config/xinetd.d [file=/etc/xinetd.conf] [line=14]
Apr 11 11:15:55 raspberrymatic daemon.crit xinetd[1869]: 1869 {init_services} no services. Exiting...
Apr 11 11:16:57 raspberrymatic daemon.info : starting pid 11944, tty '': '/bin/mv /tmp/boot.log /var/log/boot.log'
Apr 11 11:16:57 raspberrymatic daemon.info : starting pid 11946, tty '/dev/null': '/usr/bin/monit -Ic /etc/monitrc'
Apr 11 11:16:57 raspberrymatic user.info monit[11946]: Starting Monit 5.30.0 daemon with http interface at /var/run/monit.sock
Apr 11 11:16:57 raspberrymatic user.info monit[11946]: 'raspberrymatic' Monit 5.30.0 started
Apr 11 11:16:57 raspberrymatic user.err monit[11946]: 'ssdpd' process is not running
Apr 11 11:16:57 raspberrymatic user.info monit[11946]: 'ssdpd' trying to restart
Apr 11 11:16:57 raspberrymatic user.info monit[11946]: 'ssdpd' restart: '/etc/init.d/S50ssdpd restart'
Apr 11 11:17:12 raspberrymatic user.err monit[11946]: 'ssdpd' service restarted 1 times within 1 cycles(s) - exec
Apr 11 11:17:12 raspberrymatic user.info monit[11946]: 'ssdpd' exec: '/bin/triggerAlarm.tcl ssdpd restarted WatchDog: ssdpd-restart true'
Apr 11 11:17:12 raspberrymatic user.err monit[11946]: 'ssdpd' process is not running
Apr 11 11:17:12 raspberrymatic user.info monit[11946]: 'ssdpd' trying to restart
Apr 11 11:17:12 raspberrymatic user.info monit[11946]: 'ssdpd' restart: '/etc/init.d/S50ssdpd restart'
Apr 11 11:17:12 raspberrymatic user.err monit[11946]: 'sshdEnabled' status failed (1) -- no output
Apr 11 11:17:12 raspberrymatic user.err monit[11946]: 'hs485dEnabled' status failed (2) -- grep: /var/etc/hs485d.conf: No such file or directory
Apr 11 11:17:12 raspberrymatic user.err monit[11946]: 'hmlangwEnabled' status failed (1) -- no output
Apr 11 11:17:12 raspberrymatic user.err monit[11946]: 'rfdEnabled' status failed (1) -- no output
Apr 11 11:17:12 raspberrymatic user.err monit[11946]: 'HMIPServer' process is not running
Apr 11 11:17:12 raspberrymatic user.info monit[11946]: 'HMIPServer' trying to restart
Apr 11 11:17:12 raspberrymatic user.info monit[11946]: 'HMIPServer' restart: '/etc/init.d/S62HMServer restart'
Apr 11 11:17:42 raspberrymatic user.err monit[11946]: 'HMIPServer' failed to restart (exit status 1) -- '/etc/init.d/S62HMServer restart': Stopping HMIPServer: OK Starting HMIPServer: ERROR: /dev/mmd_hmip missing
Apr 11 11:17:42 raspberrymatic user.err monit[11946]: 'ReGaHss' process is not running
Apr 11 11:17:42 raspberrymatic user.info monit[11946]: 'ReGaHss' trying to restart
Apr 11 11:17:42 raspberrymatic user.info monit[11946]: 'ReGaHss' restart: '/etc/init.d/S70ReGaHss restart'
Apr 11 11:18:13 raspberrymatic user.err monit[11946]: 'ReGaHss' failed to restart (exit status -1) -- '/etc/init.d/S70ReGaHss restart': Program timed out -- start-stop-daemon: warning: killing process 5527: No such process
Apr 11 11:18:13 raspberrymatic user.warn monit[11946]: 'hasUSB' status failed (1) -- no output
Apr 11 11:18:13 raspberrymatic user.err monit[11946]: 'internetCheckEnabled' status failed (0) -- no output
Apr 11 11:18:13 raspberrymatic user.err monit[11946]: 'hb_rf_eth-CheckEnabled' status failed (1) -- no output
Apr 11 11:18:13 raspberrymatic user.warn monit[11946]: 'rpi4usb3Check' status failed (1) -- no output
Apr 11 11:18:13 raspberrymatic user.err monit[11946]: 'tailscaleEnabled' status failed (1) -- no output
Apr 11 11:18:13 raspberrymatic user.err monit[11946]: 'multimacd' process is not running
Apr 11 11:18:13 raspberrymatic user.info monit[11946]: 'multimacd' trying to restart
Apr 11 11:18:13 raspberrymatic user.info monit[11946]: 'multimacd' restart: '/etc/init.d/S60multimacd restart'
Apr 11 11:18:43 raspberrymatic user.err monit[11946]: 'multimacd' failed to restart (exit status 0) -- '/etc/init.d/S60multimacd restart': start-stop-daemon: warning: killing process 1963: No such process
Apr 11 11:18:43 raspberrymatic user.err monit[11946]: Lookup for '/media/usb1' filesystem failed  -- not found in /proc/self/mounts
Apr 11 11:18:43 raspberrymatic user.err monit[11946]: Filesystem '/media/usb1' not mounted
Apr 11 11:18:43 raspberrymatic user.err monit[11946]: 'usb1' unable to read filesystem '/media/usb1' state
Apr 11 11:18:43 raspberrymatic user.info monit[11946]: 'usb1' trying to restart
Apr 11 11:18:56 raspberrymatic user.err monit[11946]: 'ssdpd' process is not running
Apr 11 11:18:56 raspberrymatic user.info monit[11946]: 'ssdpd' trying to restart
Apr 11 11:18:56 raspberrymatic user.info monit[11946]: 'ssdpd' restart: '/etc/init.d/S50ssdpd restart'
Apr 11 11:18:57 raspberrymatic user.err monit[11946]: 'HMIPServer' service restarted 1 times within 1 cycles(s) - exec
Apr 11 11:18:57 raspberrymatic user.info monit[11946]: 'HMIPServer' exec: '/bin/triggerAlarm.tcl HMIPServer restarted WatchDog: hmipserver-restart true'
Apr 11 11:18:57 raspberrymatic user.err monit[11946]: 'HMIPServer' process is not running
Apr 11 11:18:57 raspberrymatic user.info monit[11946]: 'HMIPServer' trying to restart
Apr 11 11:18:57 raspberrymatic user.info monit[11946]: 'HMIPServer' restart: '/etc/init.d/S62HMServer restart'
Apr 11 11:19:27 raspberrymatic user.err monit[11946]: 'HMIPServer' failed to restart (exit status 1) -- '/etc/init.d/S62HMServer restart': Stopping HMIPServer: OK Starting HMIPServer: ERROR: /dev/mmd_hmip missing
Apr 11 11:19:27 raspberrymatic user.err monit[11946]: 'ReGaHss' service restarted 1 times within 1 cycles(s) - exec
Apr 11 11:19:27 raspberrymatic user.info monit[11946]: 'ReGaHss' exec: '/bin/triggerAlarm.tcl ReGaHss restarted WatchDog: regahss-restart true'
Apr 11 11:19:27 raspberrymatic user.err monit[11946]: 'ReGaHss' process is not running
Apr 11 11:19:27 raspberrymatic user.info monit[11946]: 'ReGaHss' trying to restart
Apr 11 11:19:27 raspberrymatic user.info monit[11946]: 'ReGaHss' restart: '/etc/init.d/S70ReGaHss restart'

Auszug aus dem docker-compose:

Code: Alles auswählen

version: '3.4'
services:
  raspberrymatic:
    image: ghcr.io/jens-maus/raspberrymatic:latest
    container_name: raspberrymatic
    hostname: raspberrymatic
    privileged: true
    restart: unless-stopped
    stop_grace_period: 30s
    volumes:
      - ./ccu-data:/usr/local:rw
      - /lib/modules:/lib/modules:ro
      - /run/udev/control:/run/udev/control
    networks:
      internal:
      homeassistant:
      docker_macvlan:
        ipv4_address: '10.0.10.104'
    labels:
      - traefik.enable=true
      - traefik.http.services.raspberrymatic-http.loadbalancer.server.port=80

      - traefik.http.routers.raspberrymatic-http.rule=Host(`raspberrymatic.home`, `homematic.home`, `ccu.home`)
      - traefik.http.routers.raspberrymatic-http.entrypoints=http
      - traefik.http.routers.raspberrymatic-http.service=raspberrymatic-http
Zuletzt geändert von Molt am 08.11.2023, 13:26, insgesamt 1-mal geändert.

Benutzeravatar
jmaus
Beiträge: 9818
Registriert: 17.02.2015, 14:45
System: Alternative CCU (auf Basis OCCU)
Wohnort: Dresden
Hat sich bedankt: 459 Mal
Danksagung erhalten: 1855 Mal
Kontaktdaten:

Re: Raspberrymatic auf Docker fährt nicht mehr hoch - Web-UI nicht zugreifbar

Beitrag von jmaus » 11.04.2023, 13:15

Auch dieses mal wird es vmtl mit Veränderungen (Kernel Update, apt updates, etc.) am Host system zusammenhängen. Einfach mal die pivccu kernel dependencies neu/frisch installieren wie das in der Grundanleitung zur Installation des RaspberryMatic Docker Containers beschrieben ist.
RaspberryMatic 3.75.6.20240316 @ ProxmoxVE – ~200 Hm-RF/HmIP-RF/HmIPW Geräte + ioBroker + HomeAssistant – GitHub / Sponsors / PayPal / ☕️

Molt
Beiträge: 18
Registriert: 18.02.2022, 17:02
System: in Planung
Hat sich bedankt: 4 Mal

Re: Raspberrymatic auf Docker fährt nicht mehr hoch - Web-UI nicht zugreifbar

Beitrag von Molt » 11.04.2023, 14:47

Hmmm, leider nicht - ich hatte die Schritte unter 4. in der Anleitung (https://github.com/jens-maus/RaspberryM ... Docker-OCI) schon ausgeführt - habe jetzt nochmal fresh gemacht, indem ich erst einmal deinstalliert habe:

Code: Alles auswählen

sudo apt purge pivccu pivccu-modules-raspberrypi pivccu-modules-dkms
sudo rm /etc/apt/sources.list.de/pivccu.list
sudo apt update
Ich bin auf UBuntu 18.04, falls das noch irgendwas hilft. Ich weiß leider nicht, wo ich noch gucken/rumprobieren soll

mobilebaumi
Beiträge: 5
Registriert: 21.04.2023, 16:45
System: Alternative CCU (auf Basis OCCU)

Re: Raspberrymatic auf Docker fährt nicht mehr hoch - Web-UI nicht zugreifbar

Beitrag von mobilebaumi » 21.04.2023, 17:13

Auch bei mir läuft RaspberryMatic jetzt nicht mehr unter folgender Kombination (vor kurzem alles aktualisiert):

RaspberryMatic 3.69.6.20230407 @ Proxmox 7.4-3
Debian 11 - Kernelversion: Linux 5.15.104-1-pve #1 SMP PVE 5.15.104-2 (2023-04-12T11:23Z)
Module: pivccu, Version: 1.0.80, Kernel: 4.19.0-23-amd64 (x86_64)

Gestern kam bei mir auch die neue Version: pivccu-modules-dkms ---> läuft auch nicht
Bleibt nur der blaue Bildschirm mit Logo zu sehen.

Hat schon einer eine Lösung gefunden?

Log über Portainer:

Requesting system reboot
Identifying host system: oci, OK
Initializing RTC Clock: onboard, OK
Running sysctl: OK
Checking for Factory Reset: not required
Checking for Backup Restore: not required
Initializing System: OK
Setup ca-certificates: OK
Starting logging: OK
Populating /dev using udev: done
Init onboard LEDs: init, OK
Starting irqbalance: OK
Saving 256 bits of creditable seed for next boot
Starting iptables: OK
Starting network: eth0: link up, fixed, firewall, inet up, 172.18.0.5, OK
Identifying Homematic RF-Hardware: ......HmRF: RPI-RF-MOD/HB-RF-ETH@192.168.x.x, HmIP: RPI-RF-MOD/HB-RF-ETH@192.168.x.x, OK
Updating Homematic RF-Hardware: RPI-RF-MOD: 4.4.22, not necessary, OK
Starting hs485dLoader: disabled
Starting xinetd: OK
Starting eq3configd: OK
Starting lighttpd: OK
Starting ser2net: disabled
Starting ssdpd: OK
Starting NUT services: disabled
Initializing Third-Party Addons: OK
Starting LGWFirmwareUpdate: ...OK
Setting LAN Gateway keys: OK
Starting hs485d: disabled
Starting multimacd: ...........ERROR
Starting rfd: ERROR: /dev/mmd_bidcos missing, ....................ERROR
Starting HMIPServer: ERROR: /dev/mmd_hmip missing
Starting ReGaHss: ....................ERROR

Starting CloudMatic: OK
Starting NeoServer: OK
Starting Third-Party Addons: OK
Starting crond: OK
Setup onboard LEDs: booted, OK
Finished Boot: 3.69.6.20230407 (raspmatic_oci_amd64)
RaspberryMatic 3.69.6.20230407 @ Proxmox 7.4-3
Debian 11 - Kernelversion: Linux 5.15.104-1-pve #1 SMP PVE 5.15.104-2 (2023-04-12T11:23Z)
Module: pivccu, Version: 1.0.80, Kernel: 4.19.0-23-amd64 (x86_64)

Auweia
Beiträge: 89
Registriert: 04.08.2012, 16:57
Wohnort: Regensburg
Hat sich bedankt: 3 Mal
Danksagung erhalten: 2 Mal

Re: Raspberrymatic auf Docker fährt nicht mehr hoch - Web-UI nicht zugreifbar

Beitrag von Auweia » 21.04.2023, 19:39

Hi,
bei mir läuft die Docker Version mit der aktuellen CCU Firmware Version, aber mit einem 32bit Kernel.
m.W. läuft die pivccu-modules-dkms nicht mit 64bit Kernel:

pi@rpi4-docker:~ $ uname -a
Linux rpi4-docker 6.1.21-v7l+ #1642 SMP Mon Apr 3 17:22:30 BST 2023 armv7l GNU/Linux
pi@rpi4-docker:~
Der Standard beim Rpi4b8g wurde vor kurzem auf 64bit gesetzt, deshalb musste in der config.txt:
arm_64bit=0
gesetzt werden.
RaspberryMatic , Rpi4B, SSD, RPI-RF-MOD, 1x LAN-, 1x LAN RF Gateway, 90 HM-Geräte, HPCL (Prod)
RPI4B, 8GB, SSD, Docker: RaspberryMatic RPI-RF-MOD (Test)
RPI4B, 4GB, SSD, Influx-DB, Grafana, OWFS, 1-W, KNX, NodeRed, CometVisu (Prod)

Benutzeravatar
deimos
Beiträge: 5383
Registriert: 20.06.2017, 10:38
System: Alternative CCU (auf Basis OCCU)
Wohnort: Leimersheim
Hat sich bedankt: 121 Mal
Danksagung erhalten: 949 Mal
Kontaktdaten:

Re: Raspberrymatic auf Docker fährt nicht mehr hoch - Web-UI nicht zugreifbar

Beitrag von deimos » 21.04.2023, 19:45

Hi,

doch, das läuft mit 64 Bit, aber nicht im Mischbetrieb mit 64 Bit Kernel und 32 Bit Image, sondern entweder rein im 32 Bit System oder rein im 64 Bit System.

Da mit der HB-RF-ETH dem Log nach kommuniziert werden kann, behaupte ich mal, dass es nicht an den Kernel Modulen liegt.

Viele Grüße
Alex

mobilebaumi
Beiträge: 5
Registriert: 21.04.2023, 16:45
System: Alternative CCU (auf Basis OCCU)

Re: Raspberrymatic auf Docker fährt nicht mehr hoch - Web-UI nicht zugreifbar

Beitrag von mobilebaumi » 21.04.2023, 22:34

Es lief bis vor zwei Wochen ja ca. 2 Jahre ohne Probleme
Egal welches Update von Proxmox, dem Debian, dem Home Assistant oder dem RaspberrryMatic ich durchgeführt habe.
Glaub nach dem letzten Update von Raspberrymatic wars vorbei :-(
RaspberryMatic 3.69.6.20230407 @ Proxmox 7.4-3
Debian 11 - Kernelversion: Linux 5.15.104-1-pve #1 SMP PVE 5.15.104-2 (2023-04-12T11:23Z)
Module: pivccu, Version: 1.0.80, Kernel: 4.19.0-23-amd64 (x86_64)

Molt
Beiträge: 18
Registriert: 18.02.2022, 17:02
System: in Planung
Hat sich bedankt: 4 Mal

Re: Raspberrymatic auf Docker fährt nicht mehr hoch - Web-UI nicht zugreifbar

Beitrag von Molt » 03.05.2023, 13:30

Also, bei mir ist auch nachwievor alles tot :-(

Hat einer derjenigen, bei denen es auch tot war, schon wieder Leben gefunden und kann den Ansatz teilen? :-)

mobilebaumi
Beiträge: 5
Registriert: 21.04.2023, 16:45
System: Alternative CCU (auf Basis OCCU)

Re: Raspberrymatic auf Docker fährt nicht mehr hoch - Web-UI nicht zugreifbar

Beitrag von mobilebaumi » 29.05.2023, 10:39

Molt hat geschrieben:
03.05.2023, 13:30
Also, bei mir ist auch nachwievor alles tot :-(

Hat einer derjenigen, bei denen es auch tot war, schon wieder Leben gefunden und kann den Ansatz teilen? :-)
Also bei mir geht nach wie vor auch nichts.
Finde es schade, daß nicht mal ein Tipp kommt, was man probieren könnte, bzw. welche Infos von uns noch gebraucht werden.
RaspberryMatic 3.69.6.20230407 @ Proxmox 7.4-3
Debian 11 - Kernelversion: Linux 5.15.104-1-pve #1 SMP PVE 5.15.104-2 (2023-04-12T11:23Z)
Module: pivccu, Version: 1.0.80, Kernel: 4.19.0-23-amd64 (x86_64)

MichaelN
Beiträge: 9561
Registriert: 27.04.2020, 10:34
System: CCU
Hat sich bedankt: 696 Mal
Danksagung erhalten: 1608 Mal

Re: Raspberrymatic auf Docker fährt nicht mehr hoch - Web-UI nicht zugreifbar

Beitrag von MichaelN » 29.05.2023, 10:53

Tipp : Ihr könnt das RaspberryMatic Backup in jede andere RaspberryMatic Installation einspielen. Wenn docker zu komplex ist, geht zum Beispiel ein einfacher rpi3 oder eine VM unter virtual box.
LG, Michael.

Wenn du eine App zur Bedienung brauchst, dann hast du kein Smarthome.

Wettervorhersage über AccuWeather oder OpenWeatherMap+++ Rollladensteuerung 2.0 +++ JSON-API-Ausgaben auswerten +++ undokumentierte Skript-Befehle und Debugging-Tipps +++

Antworten

Zurück zu „RaspberryMatic“