RaspberryMatic 3.75.6.20240316 – Neue Version

[Baxxy]

Du hast aber auch immer Pech mit deinem Odroid.
Der aktuelle Nightly beinhaltet, bezogen auf die Release-Version und den Odroid, keinerlei Änderungen.
Vielleicht wieder ein Ticket aufmachen?

[zautrix]

Beim Pi4B geht's ums booten von USB-SSD, das klappt aktuell mit der 8GB Version nicht.

ist bei mir auch genau so, wie du schreibst.
Der Pi4 mit 4 GB bootet von SSD , der Pi4 mit 8 GB kommt in eine Schleife.

Habe mir dann überlegt, wie ich den Pi4 mit 8 GB beim Start "kitzeln" kann, dass er kurz verhofft.
Habe bei dem Pi4 mit 8 GB eine ( 8 GB große ) SD Karte, leer und Windows formatiert, in den SD Slot gesteckt.
Und siehe da, jetzt bootet er von der 120 GB SSD (angeschlossen am USB3 Port)
Ist für mich erst mal als Workaround akzeptabel.

[Baxxy]

Das ist ja mal ein netter Workaround.
Habe jetzt auch ne leere FAT32 formatierte SD-Karte drin und schwupps wird von der SSD gebootet.

Bisschen aufpassen muss man da die SD-Karte als "USB-Stick" in RM gemounted wird.

[jmaus]

Das ist ja mal ein netter Workaround.
Habe jetzt auch ne leere FAT32 formatierte SD-Karte drin und schwupps wird von der SSD gebootet.

Bisschen aufpassen muss man da die SD-Karte als "USB-Stick" in RM gemounted wird.

Für dieses positive Bootszenario würden mich mal konkret die Ausgaben am HDMI und auch die letztendlichen Ausgaben von "dmesg" interessieren nachdem ein solches System hochgefahren ist...

[Baxxy]

Hat jemand mit dieser Version einen erhöhten DC beobachtet?
Speziell Nutzer mit 2-Punkt Regelungen (HmIP-WTH/STH/STHD <--> IP-Schaltaktor) sollten mal genauer hinsehen.

Mein Idle-DC (Ferienhaus ist unbewohnt und wird aktuell nicht beheizt) hat sich etwa verdoppelt.

[zautrix]

ses positive Bootszenario würden mich mal konkret die Ausgaben am HDMI und auch die letztendlichen Ausgaben von "dmesg" interessieren nachdem ein solches System hochgefahren ist...

Hier die Ausgabe am HDMI, wo der P4 in die Loop kommt.
Sind ein paar Typos drin, da die OCR Texterkennung vom Bildschirmfoto nicht alles richtig erkannt hat.

Code: Alles auswählen

Net: eth0: ethernet@7d580000
PCIe BRCM: link up, 5.0 Gbps x1 (SSC)
starting USB...
Bus xhci_pci: Register 5000420 NbrPorts 5
Starting the controller
USB XHCI 1.00
scanning bus xhci_pci for devices... 4 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
sdhci_set_clock: Timeout to wait cmd & data inhibit
sdhci_set_clock: Timeout to wait cmd & data inhibit
sdhci_set_clock: Timeout to wait cmd & data inhibit
sdhci_send_command: MMC: 1 busy timeout increasing to: 200 ms.
sdhci_send_command: MMC: 1 busy timeout increasing to: 400 ns.
sdhci_send_command: MMC: 1 busy timeout increasing to: 800 ns.
sdhci_send_command: MMC: 1 busy timeout increasing to: 1600 ms.
sdhci_send_command: MMC: 1 busy timeout increasing to: 3200 ms.
sdhci_send_command: MMC: 1 busy timeout.
sdhci_set_clock: Timeout to wait cnd & data inhibit
sdhci_set_clock: Timeout to wait cnd & data inhibit
sdhci_set_clock: Timeout to wait cnd & data inhibit
sdhci_send_command: MMC: 1 busy tineout.
sdhci_set_clock: Timeout to wait cnd & data inhibit
sdhci_set_clock: Timeout to wait cnd & data inhibit
sdhci_set_clock: Timeout to wait cnd & data inhibit
sdhci_send_command: MMC: 1 busy timeout.
Card did not respond to voltage select? -110
** Booting boot flow 'usb_mass_storage. lune.bootdev.part_1' with script
U-boot loaded from SD
gpio: pin GPI012 (gpio 12) value is 1
==== NORMAL BOOT ====
Working FDT set to Zeff2200
26049024 bytes read in 79 ms (314.5 MiB/s)
Moving Image from 0x80000 to 0x200000, end=1c30000
## Flattened Device Tree blob at Zeff2200
Booting using the fdt blob at OxZeff2200
Working FDT set to Zeff2200
Using Device Tree in place at 000000002eff2200, end 000000002f002f92
Working FDT set to Zeff2200
Starting kernel ...

Hier die Ausgabe am HDMI, wo der P4 bootet mit der SD Karte drin:
Sind ein paar Typos drin, da die OCR Texterkennung vom Bildschirmfoto nicht alles richtig erkannt hat.
Und oben links war die Einblendung des Engangs vom Monitor im Weg

Code: Alles auswählen

Net: etho: ethernet@2dd10000
USB XHCI 1.00
nk up, 5.0 Gbps x1 (SSC)
Register 5000420 NbrPorts 5
controller
Scanning bus xhci_pci for devices... 4 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Card did not respond to voltage select! : -110
Booting bootflow 'usb_nass_storage. lun0.bootdev.part_1' with script
U-boot loaded from SD
gpio: pin GPI012 (gpio 12) value is 1
==== NORMAL BOOT ====
Working FDT set to Zeff2200
26049024 bytes read in 79 ms (314.5 MiB/s)
Moving Image from 0x80000 to 0x200000, end=1c30000
## Flattened Device Tree blob at Zeff2200
Booting using the fdt blob at 0x2eff2200
Working FDT set to Zeff2200
Using Device Tree in place at 000000002eff2200, end 000000002f002f92
Working FDT set to Zeff2200
Starting kernel ...

Hier die Ausgaben von meiner von mir selbst kompilierten Raspimatic (Wesentliche Änderungen: rootfs ist 3 GB groß und rw mounted)
Mit der SD Karte drin, damit es bootet.
Alles Pi4 mit 8 GB Speicher

Code: Alles auswählen

root@zz-broma:~# dmesg
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083]
[    0.000000] Linux version 6.1.73 (polo@q4os-desktop) (aarch64-buildroot-linux-gnu-gcc.br_real (Buildroot 3.75.6.20240316-dirty) 12.3.0, GNU ld (GNU Binutils) 2.40) #1 SMP PREEMPT Tue Mar 19 10:58:53 CET 2024
[    0.000000] Kernel is locked down from Kernel configuration; see man kernel_lockdown.7
[    0.000000] random: crng init done
[    0.000000] Machine model: Raspberry Pi 4 Model B Rev 1.4
[    0.000000] efi: UEFI not found.
[    0.000000] Reserved memory: created CMA memory pool at 0x000000002ac00000, size 64 MiB
[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000000000-0x000000003fffffff]
[    0.000000]   DMA32    [mem 0x0000000040000000-0x00000000ffffffff]
[    0.000000]   Normal   [mem 0x0000000100000000-0x00000001ffffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x000000003defffff]
[    0.000000]   node   0: [mem 0x0000000040000000-0x00000000fbffffff]
[    0.000000]   node   0: [mem 0x0000000100000000-0x00000001ffffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000001ffffffff]
[    0.000000] On node 0, zone DMA32: 8448 pages in unavailable ranges
[    0.000000] On node 0, zone Normal: 16384 pages in unavailable ranges
[    0.000000] percpu: Embedded 28 pages/cpu s75176 r8192 d31320 u114688
[    0.000000] pcpu-alloc: s75176 r8192 d31320 u114688 alloc=28*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[    0.000000] Detected PIPT I-cache on CPU0
[    0.000000] CPU features: detected: Spectre-v2
[    0.000000] CPU features: detected: Spectre-v3a
[    0.000000] CPU features: detected: Spectre-v4
[    0.000000] CPU features: detected: Spectre-BHB
[    0.000000] CPU features: kernel page table isolation forced ON by KASLR
[    0.000000] CPU features: detected: Kernel page table isolation (KPTI)
[    0.000000] CPU features: detected: ARM erratum 1742098
[    0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[    0.000000] alternatives: applying boot alternatives
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 2039552
[    0.000000] Kernel command line: dwc_otg.lpm_enable=0 sdhci_bcm2708.enable_llm=0 console=tty2 root=PARTUUID=deedbeef-02 rw rootfstype=ext4 fsck.repair=yes rootwait rootdelay=5 consoleblank=120 logo.nologo quiet loglevel=0 init_on_alloc=1 init_on_free=1 slab_nomerge iomem=relaxed net.ifnames=0 usb-storage.quirks=174c:55aa:u,2109:0715:u,152d:0578:u,152d:0579:u,152d:1561:u,174c:0829:u,14b0:0206:u,174c:225c:u,7825:a2a4:u,152d:0562:u  coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_headphones=0 bcm2708_fb.fbwidth=640 bcm2708_fb.fbheight=480 bcm2708_fb.fbswap=1 smsc95xx.macaddr=E4:5F:01:6F:06:D5 vc_mem.mem_base=0x3eb00000 vc_mem.mem_size=0x3ff00000  empty
[    0.000000] Unknown kernel command line parameters "empty", will be passed to user space.
[    0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[    0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[    0.000000] mem auto-init: stack:all(zero), heap alloc:on, heap free:on
[    0.000000] mem auto-init: clearing system memory may take some time...
[    0.000000] software IO TLB: area num 4.
[    0.000000] software IO TLB: mapped [mem 0x0000000039f00000-0x000000003df00000] (64MB)
[    0.000000] Memory: 7968180K/8289280K available (14848K kernel code, 2078K rwdata, 4112K rodata, 4288K init, 1353K bss, 255564K reserved, 65536K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] ftrace: allocating 40833 entries in 160 pages
[    0.000000] ftrace: allocated 160 pages with 2 groups
[    0.000000] Lockdown: swapper: use of tracefs is restricted; see man kernel_lockdown.7
[    0.000000] Tracing disabled due to lockdown
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu:     RCU event tracing is enabled.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4.
[    0.000000]  Trampoline variant of Tasks RCU enabled.
[    0.000000]  Rude variant of Tasks RCU enabled.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] Root IRQ handler: gic_handle_irq
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] arch_timer: cp15 timer(s) running at 54.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xc743ce346, max_idle_ns: 440795203123 ns
[    0.000000] sched_clock: 56 bits at 54MHz, resolution 18ns, wraps every 4398046511102ns
[    0.000339] kfence: initialized - using 2097152 bytes for 255 objects at 0x(____ptrval____)-0x(____ptrval____)
[    0.000493] Console: colour dummy device 80x25
[    0.000549] printk: console [tty2] enabled
[    0.000598] Calibrating delay loop (skipped), value calculated using timer frequency.. 108.00 BogoMIPS (lpj=216000)
[    0.000616] pid_max: default: 32768 minimum: 301
[    0.000761] LSM: Security Framework initializing
[    0.000826] landlock: Up and running.
[    0.000832] Yama: becoming mindful.
[    0.000944] AppArmor: AppArmor initialized
[    0.001093] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.001112] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.002105] cgroup: Disabling memory control group subsystem
[    0.003681] cblist_init_generic: Setting adjustable number of callback queues.
[    0.003695] cblist_init_generic: Setting shift to 2 and lim to 1.
[    0.003811] cblist_init_generic: Setting adjustable number of callback queues.
[    0.003820] cblist_init_generic: Setting shift to 2 and lim to 1.
[    0.003981] cblist_init_generic: Setting adjustable number of callback queues.
[    0.003990] cblist_init_generic: Setting shift to 2 and lim to 1.
[    0.004246] rcu: Hierarchical SRCU implementation.
[    0.004255] rcu:     Max phase no-delay instances is 1000.
[    0.006040] EFI services will not be available.
[    0.006392] smp: Bringing up secondary CPUs ...
[    0.007012] Detected PIPT I-cache on CPU1
[    0.007170] CPU1: Booted secondary processor 0x0000000001 [0x410fd083]
[    0.007871] Detected PIPT I-cache on CPU2
[    0.008000] CPU2: Booted secondary processor 0x0000000002 [0x410fd083]
[    0.008685] Detected PIPT I-cache on CPU3
[    0.008816] CPU3: Booted secondary processor 0x0000000003 [0x410fd083]
[    0.008909] smp: Brought up 1 node, 4 CPUs
[    0.008927] SMP: Total of 4 processors activated.
[    0.008936] CPU features: detected: 32-bit EL0 Support
[    0.008944] CPU features: detected: CRC32 instructions
[    0.009045] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[    0.009056] CPU: All CPU(s) started at EL2
[    0.009061] alternatives: applying system-wide alternatives
[    0.011258] devtmpfs: initialized
[    0.022348] Enabled cp15_barrier support
[    0.022380] Enabled setend support
[    0.022529] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.022557] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.022675] Lockdown: swapper/0: use of tracefs is restricted; see man kernel_lockdown.7
[    0.022684] Can not register tracer wakeup due to lockdown
[    0.022696] Lockdown: swapper/0: use of tracefs is restricted; see man kernel_lockdown.7
[    0.022703] Can not register tracer function_graph due to lockdown
[    0.063945] pinctrl core: initialized pinctrl subsystem
[    0.064682] DMI not present or invalid.
[    0.065203] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.069277] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations
[    0.069591] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.070617] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.070733] audit: initializing netlink subsys (disabled)
[    0.070985] audit: type=2000 audit(0.068:1): state=initialized audit_enabled=0 res=1
[    0.071522] thermal_sys: Registered thermal governor 'step_wise'
[    0.071587] cpuidle: using governor menu
[    0.072244] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.072385] ASID allocator initialised with 32768 entries
[    0.079996] bcm2835-mbox fe00b880.mailbox: mailbox enabled
[    0.088223] raspberrypi-firmware soc:firmware: Attached to firmware from 2023-10-17T15:39:16, variant start
[    0.092235] raspberrypi-firmware soc:firmware: Firmware hash is 30f0c5e4d076da3ab4f341d88e7d505760b93ad7
[    0.102099] KASLR enabled
[    0.127391] bcm2835-dma fe007000.dma: DMA legacy API manager, dmachans=0x1
[    0.130348] iommu: Default domain type: Translated
[    0.130363] iommu: DMA domain TLB invalidation policy: strict mode
[    0.130762] SCSI subsystem initialized
[    0.130954] usbcore: registered new interface driver usbfs
[    0.131001] usbcore: registered new interface driver hub
[    0.131042] usbcore: registered new device driver usb
[    0.131210] usb_phy_generic phy: supply vcc not found, using dummy regulator
[    0.131549] pps_core: LinuxPPS API ver. 1 registered
[    0.131559] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.131578] PTP clock support registered
[    0.132644] vgaarb: loaded
[    0.133497] clocksource: Switched to clocksource arch_sys_counter
[    0.133513] Lockdown: swapper/0: use of tracefs is restricted; see man kernel_lockdown.7
[    0.133521] Tracing disabled due to lockdown
[    0.133528] Lockdown: swapper/0: use of tracefs is restricted; see man kernel_lockdown.7
[    0.133535] Tracing disabled due to lockdown
[    0.133547] Lockdown: swapper/0: use of tracefs is restricted; see man kernel_lockdown.7
[    0.133554] Tracing disabled due to lockdown
[    0.133563] Lockdown: swapper/0: use of tracefs is restricted; see man kernel_lockdown.7
[    0.133569] Tracing disabled due to lockdown
[    0.133576] Lockdown: swapper/0: use of tracefs is restricted; see man kernel_lockdown.7
[    0.133582] Tracing disabled due to lockdown
[    0.133950] VFS: Disk quotas dquot_6.6.0
[    0.134008] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.134107] FS-Cache: Loaded
[    0.134262] CacheFiles: Loaded
[    0.134770] AppArmor: AppArmor Filesystem Enabled
[    0.143722] NET: Registered PF_INET protocol family
[    0.143885] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.152980] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear)
[    0.153079] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.153123] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.153543] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, linear)
[    0.155753] TCP: Hash tables configured (established 65536 bind 65536)
[    0.156105] MPTCP token hash table entries: 8192 (order: 5, 196608 bytes, linear)
[    0.156418] UDP hash table entries: 4096 (order: 5, 131072 bytes, linear)
[    0.156520] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear)
[    0.156794] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.157530] RPC: Registered named UNIX socket transport module.
[    0.157544] RPC: Registered udp transport module.
[    0.157550] RPC: Registered tcp transport module.
[    0.157555] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.157570] PCI: CLS 0 bytes, default 64
[    0.159769] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
[    0.160827] Lockdown: swapper/0: use of tracefs is restricted; see man kernel_lockdown.7
[    0.160840] Tracing disabled due to lockdown
[    0.160849] Lockdown: swapper/0: use of tracefs is restricted; see man kernel_lockdown.7
[    0.160855] Can not register tracer blk due to lockdown
[    0.160862] blktrace: Warning: could not register the block tracer
[    0.161192] Initialise system trusted keyrings
[    0.161444] workingset: timestamp_bits=46 max_order=21 bucket_order=0
[    0.173074] NFS: Registering the id_resolver key type
[    0.173119] Key type id_resolver registered
[    0.173126] Key type id_legacy registered
[    0.173223] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.173244] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[    0.173282] ntfs: driver 2.1.32 [Flags: R/W].
[    0.175537] Key type asymmetric registered
[    0.175551] Asymmetric key parser 'x509' registered
[    0.175621] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    0.175861] io scheduler mq-deadline registered
[    0.175873] io scheduler kyber registered
[    0.181579] brcm-pcie fd500000.pcie: host bridge /scb/pcie@7d500000 ranges:
[    0.181615] brcm-pcie fd500000.pcie:   No bus range found for /scb/pcie@7d500000, using [bus 00-ff]
[    0.181656] brcm-pcie fd500000.pcie:      MEM 0x0600000000..0x063fffffff -> 0x00c0000000
[    0.181692] brcm-pcie fd500000.pcie:   IB MEM 0x0000000000..0x01ffffffff -> 0x0400000000
[    0.182202] brcm-pcie fd500000.pcie: setting SCB_ACCESS_EN, READ_UR_MODE, MAX_BURST_SIZE
[    0.182524] brcm-pcie fd500000.pcie: PCI host bridge to bus 0000:00
[    0.182540] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.182554] pci_bus 0000:00: root bus resource [mem 0x600000000-0x63fffffff] (bus address [0xc0000000-0xffffffff])
[    0.182599] pci 0000:00:00.0: [14e4:2711] type 01 class 0x060400
[    0.182689] pci 0000:00:00.0: PME# supported from D0 D3hot
[    0.186595] pci_bus 0000:01: supply vpcie3v3 not found, using dummy regulator
[    0.186730] pci_bus 0000:01: supply vpcie3v3aux not found, using dummy regulator
[    0.186787] pci_bus 0000:01: supply vpcie12v not found, using dummy regulator
[    0.295587] brcm-pcie fd500000.pcie: link up, 5.0 GT/s PCIe x1 (SSC)
[    0.295771] pci 0000:01:00.0: [1106:3483] type 00 class 0x0c0330
[    0.295864] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00000fff 64bit]
[    0.296148] pci 0000:01:00.0: PME# supported from D0 D3hot
[    0.305608] pci 0000:00:00.0: BAR 8: assigned [mem 0x600000000-0x6000fffff]
[    0.305631] pci 0000:01:00.0: BAR 0: assigned [mem 0x600000000-0x600000fff 64bit]
[    0.305692] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.305705] pci 0000:00:00.0:   bridge window [mem 0x600000000-0x6000fffff]
[    0.305935] pcieport 0000:00:00.0: enabling device (0000 -> 0002)
[    0.306093] pcieport 0000:00:00.0: PME: Signaling with IRQ 30
[    0.306389] pcieport 0000:00:00.0: AER: enabled with IRQ 30
[    0.307143] simple-framebuffer 3e9ca000.framebuffer: framebuffer at 0x3e9ca000, 0x12c000 bytes
[    0.307159] simple-framebuffer 3e9ca000.framebuffer: format=a8r8g8b8, mode=640x480x32, linelength=2560
[    0.307608] Console: switching to colour frame buffer device 80x30
[    0.308900] simple-framebuffer 3e9ca000.framebuffer: fb0: simplefb registered!
[    0.313871] Serial: 8250/16550 driver, 1 ports, IRQ sharing enabled
[    0.315627] iproc-rng200 fe104000.rng: hwrng registered
[    0.315862] vc-mem: phys_addr:0x00000000 mem_base=0x3eb00000 mem_size:0x3ff00000(1023 MiB)
[    0.326727] brd: module loaded
[    0.332951] loop: module loaded
[    0.333448] zram: Added device: zram0
[    0.334082] Loading iSCSI transport class v2.0-870.
[    0.337341] tun: Universal TUN/TAP device driver, 1.6
[    0.338333] bcmgenet fd580000.ethernet: GENET 5.0 EPHY: 0x0000
[    0.437620] unimac-mdio unimac-mdio.-19: Broadcom UniMAC MDIO bus
[    0.484293] xhci_hcd 0000:01:00.0: xHCI Host Controller
[    0.484329] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 1
[    0.484843] xhci_hcd 0000:01:00.0: hcc params 0x002841eb hci version 0x100 quirks 0x0b00040000000890
[    0.485664] xhci_hcd 0000:01:00.0: xHCI Host Controller
[    0.485686] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[    0.485704] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed
[    0.485977] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[    0.485995] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.486006] usb usb1: Product: xHCI Host Controller
[    0.486016] usb usb1: Manufacturer: Linux 6.1.73 xhci-hcd
[    0.486025] usb usb1: SerialNumber: 0000:01:00.0
[    0.486574] hub 1-0:1.0: USB hub found
[    0.486622] hub 1-0:1.0: 1 port detected
[    0.487216] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01
[    0.487233] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.487244] usb usb2: Product: xHCI Host Controller
[    0.487253] usb usb2: Manufacturer: Linux 6.1.73 xhci-hcd
[    0.487262] usb usb2: SerialNumber: 0000:01:00.0
[    0.487741] hub 2-0:1.0: USB hub found
[    0.487787] hub 2-0:1.0: 4 ports detected
[    0.488790] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[    0.488892] dwc_otg: FIQ enabled
[    0.488899] dwc_otg: NAK holdoff enabled
[    0.488905] dwc_otg: FIQ split-transaction FSM enabled
[    0.488915] Module dwc_common_port init
[    0.489634] usbcore: registered new interface driver uas
[    0.489720] usbcore: registered new interface driver usb-storage
[    0.489809] usbcore: registered new interface driver usbserial_generic
[    0.489836] usbserial: USB Serial support registered for generic
[    0.490260] Driver for 1-wire Dallas network protocol.
[    0.491617] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com
[    0.494258] sdhci: Secure Digital Host Controller Interface driver
[    0.494273] sdhci: Copyright(c) Pierre Ossman
[    0.494481] Error: Driver 'sdhost-bcm2835' is already registered, aborting...
[    0.494490] sdhci-pltfm: SDHCI platform and OF driver helper
[    0.499325] ledtrig-cpu: registered to indicate activity on CPUs
[    0.499407] hid: raw HID events driver (C) Jiri Kosina
[    0.499538] usbcore: registered new interface driver usbhid
[    0.499541] usbhid: USB HID core driver
[    0.505218] NET: Registered PF_INET6 protocol family
[    0.506090] Segment Routing with IPv6
[    0.506111] In-situ OAM (IOAM) with IPv6
[    0.506182] NET: Registered PF_PACKET protocol family
[    0.506223] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    0.506269] Key type dns_resolver registered
[    0.506842] registered taskstats version 1
[    0.506868] Loading compiled-in X.509 certificates
[    0.509114] Loaded X.509 cert 'Build time autogenerated kernel key: b626fb849bcc9a12e7b33c39d8a072461e2039cf'
[    0.509324] Key type .fscrypt registered
[    0.509329] Key type fscrypt-provisioning registered
[    0.509444] AppArmor: AppArmor sha1 policy hashing enabled
[    0.522559] fe215040.serial: ttyS0 at MMIO 0xfe215040 (irq = 35, base_baud = 62500000) is a 16550
[    0.523153] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer
[    0.523294] bcm2835-power bcm2835-power: Broadcom BCM2835 power domains driver
[    0.523738] mmc-bcm2835 fe300000.mmcnr: mmc_debug:0 mmc_debug2:0
[    0.523747] mmc-bcm2835 fe300000.mmcnr: DMA channel allocated
[    0.551082] of_cfs_init
[    0.551205] of_cfs_init: OK
[    0.552346] Waiting 5 sec before mounting root device...
[    0.589891] mmc0: SDHCI controller on fe340000.mmc [fe340000.mmc] using ADMA
[    0.624503] mmc0: new high speed SDHC card at address 59b4
[    0.625245] mmcblk0: mmc0:59b4 USD   7.51 GiB
[    0.627330]  mmcblk0: p1
[    0.627574] mmcblk0: mmc0:59b4 USD   7.51 GiB
[    0.632903] mmc1: new high speed SDIO card at address 0001
[    0.745528] usb 1-1: new high-speed USB device number 2 using xhci_hcd
[    0.896132] usb 1-1: New USB device found, idVendor=2109, idProduct=3431, bcdDevice= 4.21
[    0.896152] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    0.896164] usb 1-1: Product: USB2.0 Hub
[    0.897446] hub 1-1:1.0: USB hub found
[    0.897732] hub 1-1:1.0: 4 ports detected
[    1.021819] usb 2-1: new SuperSpeed USB device number 2 using xhci_hcd
[    1.043188] usb 2-1: New USB device found, idVendor=152d, idProduct=0576, bcdDevice=12.14
[    1.043206] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    1.043217] usb 2-1: Product: External
[    1.043226] usb 2-1: Manufacturer: Intenso
[    1.043235] usb 2-1: SerialNumber: DD820200994A3
[    1.052353] scsi host0: uas
[    1.053447] scsi 0:0:0:0: Direct-Access     Intenso                   1214 PQ: 0 ANSI: 6
[    1.056260] sd 0:0:0:0: [sda] 250069680 512-byte logical blocks: (128 GB/119 GiB)
[    1.056273] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    1.056479] sd 0:0:0:0: [sda] Write Protect is off
[    1.056501] sd 0:0:0:0: [sda] Mode Sense: 53 00 00 08
[    1.056889] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.057329] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes
[    1.057339] sd 0:0:0:0: [sda] Optimal transfer size 33553920 bytes not a multiple of preferred minimum block size (4096 bytes)
[    1.059755]  sda: sda1 sda2 sda3
[    1.060168] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.193534] usb 1-1.2: new high-speed USB device number 3 using xhci_hcd
[    1.294129] usb 1-1.2: New USB device found, idVendor=0451, idProduct=bef3, bcdDevice= 1.00
[    1.294147] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    1.294159] usb 1-1.2: Product: XDS110 (03.00.00.15) Embed with CMSIS-DAP
[    1.294170] usb 1-1.2: Manufacturer: Texas Instruments
[    1.294178] usb 1-1.2: SerialNumber: L43003ZX
[    1.302626] hid-generic 0003:0451:BEF3.0001: hiddev96,hidraw0: USB HID v1.11 Device [Texas Instruments XDS110 (03.00.00.15) Embed with CMSIS-DAP] on usb-0000:01:00.0-1.2/input5
[    5.630149] EXT4-fs (sda2): mounted filesystem with ordered data mode. Quota mode: none.
[    5.630235] VFS: Mounted root (ext4 filesystem) on device 8:2.
[    5.630688] devtmpfs: mounted
[    5.636808] Freeing unused kernel memory: 4288K
[    5.694034] Checked W+X mappings: passed, no W+X pages found
[    5.694066] Run /sbin/init as init process
[    5.694070]   with arguments:
[    5.694072]     /sbin/init
[    5.694074]     empty
[    5.694076]   with environment:
[    5.694078]     HOME=/
[    5.694080]     TERM=linux
[    5.813534] EXT4-fs: Mount option(s) incompatible with ext2
[    5.819022] EXT4-fs (sda3): mounted filesystem with ordered data mode. Quota mode: none.
[    6.360889] zram: Added device: zram1
[    6.363721] zram1: detected capacity change from 0 to 16879816
[    6.380207] Adding 8439904k swap on /dev/zram1.  Priority:75 extents:1 across:8439904k SS
[    6.424195] i2c_dev: i2c /dev entries driver
[    6.441129] rtc-ds1307 1-0032: registered as rtc0
[    6.454692] dummy_rx8130: loading out-of-tree module taints kernel.
[    8.344846] udevd[1045]: starting version 3.2.14
[    8.373064] udevd[1045]: RUN{builtin}: 'uaccess' unknown /usr/lib/udev/rules.d/73-seat-late.rules:17
[    8.376130] udevd[1045]: IMPORT{builtin}: 'net_setup_link' unknown /usr/lib/udev/rules.d/80-net-setup-link.rules:9
[    8.381655] udevd[1046]: starting eudev-3.2.14
[    8.414303] udevd[1046]: RUN{builtin}: 'uaccess' unknown /usr/lib/udev/rules.d/73-seat-late.rules:17
[    8.414999] udevd[1046]: IMPORT{builtin}: 'net_setup_link' unknown /usr/lib/udev/rules.d/80-net-setup-link.rules:9
[    8.536101] vc_sm_cma: module is from the staging directory, the quality is unknown, you have been warned.
[    8.536903] bcm2835_vc_sm_cma_probe: Videocore shared memory driver
[    8.536920] [vc_sm_connected_init]: start
[    8.541298] rpi-gpiomem fe200000.gpiomem: window base 0xfe200000 size 0x00001000
[    8.541895] rpi-gpiomem fe200000.gpiomem: initialised 1 regions as /dev/gpiomem
[    8.547328] [vc_sm_connected_init]: installed successfully
[    8.551094] udevd[1076]: failed to execute '/lib/systemd/systemd-sysctl' '/lib/systemd/systemd-sysctl --prefix=/net/ipv4/conf/eth0 --prefix=/net/ipv4/neigh/eth0 --prefix=/net/ipv6/conf/eth0 --prefix=/net/ipv6/neigh/eth0': No such file or directory
[    8.555019] udevd[1077]: failed to execute '/usr/lib/raspberrypi-sys-mods/i2cprobe' '/usr/lib/raspberrypi-sys-mods/i2cprobe': No such file or directory
[    8.562530] pl011_raw_uart fe201000.serial: there is not valid maps for state default
[    8.562707] pl011_raw_uart fe201000.serial: Initialized pl011 device; mapbase=0xfe201000; irq=39; clockrate=48000001
[    8.562769] pl011_raw_uart fe201000.serial: Detected RPI-RF-MOD, using alternative reset pin
[    8.563089] raw-uart raw-uart: Reset radio module
[    8.661136] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    8.673562] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    8.680996] cfg80211: Loaded X.509 cert 'benh@debian.org: 577e021cb980e0e820821ba7b54b4961b8b4fadf'
[    8.681398] cfg80211: Loaded X.509 cert 'romain.perier@gmail.com: 3abbc6ec146e09d1b6016ab9d6cf71dd233f0328'
[    8.681996] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    8.682375] cfg80211: Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600'
[    8.721384] brcmfmac: F1 signature read @0x18000000=0x15264345
[    8.728678] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[    8.730145] usbcore: registered new interface driver brcmfmac
[    8.741532] raw-uart raw-uart: Registered new raw-uart device using underlying device GPIO@fe201000.serial.
[    8.742009] udevd[1113]: failed to execute '/etc/console-setup/cached_setup_font.sh' '/etc/console-setup/cached_setup_font.sh': No such file or directory
[    8.748245] udevd[1114]: failed to execute '/etc/console-setup/cached_setup_font.sh' '/etc/console-setup/cached_setup_font.sh': No such file or directory
[    8.750912] udevd[1116]: failed to execute '/usr/lib/raspberrypi-sys-mods/i2cprobe' '/usr/lib/raspberrypi-sys-mods/i2cprobe': No such file or directory
[    8.756944] cdc_acm 1-1.2:1.0: ttyACM0: USB ACM device
[    8.858826] cdc_acm 1-1.2:1.3: ttyACM1: USB ACM device
[    8.859010] usbcore: registered new interface driver cdc_acm
[    8.859022] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    8.932213] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Nov  1 2021 00:37:25 version 7.45.241 (1a2f2fa CY) FWID 01-703fd60
[    9.138560] bcmgenet fd580000.ethernet: configuring instance for external RGMII (RX delay)
[    9.139533] bcmgenet fd580000.ethernet eth0: Link is Down
[   13.213775] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   13.214265] bcmgenet fd580000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[   22.166793] raw-uart raw-uart: Reset radio module
[   22.305921] udevd[1396]: failed to execute '/lib/systemd/systemd-sysctl' '/lib/systemd/systemd-sysctl --prefix=/net/ipv4/conf/tailscale0 --prefix=/net/ipv4/neigh/tailscale0 --prefix=/net/ipv6/conf/tailscale0 --prefix=/net/ipv6/neigh/tailscale0': No such file or directory
[   24.364001] raw-uart raw-uart: Reset radio module
[   26.849094] raw-uart raw-uart: Reset radio module
[   41.809070] eq3loop: created slave mmd_hmip
[   41.809718] eq3loop: created slave mmd_bidcos
[   45.850476] eq3loop: eq3loop_open_slave() mmd_bidcos
[   45.850511] eq3loop: eq3loop_close_slave() mmd_bidcos
[   45.852341] eq3loop: eq3loop_open_slave() mmd_hmip
[   45.852390] eq3loop: eq3loop_close_slave() mmd_hmip
[   45.939784] eq3loop: eq3loop_open_slave() mmd_bidcos
[   62.714787] eq3loop: eq3loop_open_slave() mmd_hmip
[   62.715069] eq3loop: eq3loop_close_slave() mmd_hmip
[   62.717120] eq3loop: eq3loop_open_slave() mmd_hmip
[   62.717328] eq3loop: eq3loop_close_slave() mmd_hmip
[   62.718050] eq3loop: eq3loop_open_slave() mmd_hmip
[   62.718210] eq3loop: eq3loop_close_slave() mmd_hmip
[   62.723162] eq3loop: eq3loop_open_slave() mmd_hmip
[  207.093309] Bluetooth: Core ver 2.22
[  207.093473] NET: Registered PF_BLUETOOTH protocol family
[  207.093482] Bluetooth: HCI device and connection manager initialized
[  207.093500] Bluetooth: HCI socket layer initialized
[  207.093507] Bluetooth: L2CAP socket layer initialized
[  207.093524] Bluetooth: SCO socket layer initialized
root@zz-broma:~#

[andrzejgilas]

Hat jemand mit dieser Version einen erhöhten DC beobachtet?

Ich habe eine aktive Zweipunktregelung für drei BWTHs und einen WTH-1, konnte aber keine erhöhte DC
die Spitzen im Diagramm sind meine Neustarts und das Einschalten der Geräte nacheinander

[Baxxy]

Ok, Danke.
Ich weiß nicht ob BWTH's da auch involviert sein können.
Ich sehe das bei mir deutlich und kann es auch problemlos auf dem Haupt und Testsystem reproduzieren.
Hab's mal als Ticket angelegt. #2690

[MichaelN]

@Jens :

Schwachstellen u.a. im Zusammenhang mit dem Upload von Gerätefirmware wurden geschlossen (CVE-2024-24578).

Möchtest/magst du hierzu noch etwas mehr sagen oder besser den Mantel des Schweigens drüber decken?

[jp112sdl]

hierzu noch etwas mehr sagen

Was möchtest du denn noch genauer wissen, als dort geschrieben steht?

Es war möglich, eine Firmware-Datei ohne gültige Session ID hochzuladen, die dann auch automatisch entpackt wird.
Durch die Möglichkeit, Pfade im Archiv mitzugeben, kann man auch "ausbrechen" und beliebige andere Dateien im UserFS überschreiben.

Aufgefallen war dies, dass der Methode zwar eine SID übergeben wird, diese aber nicht weiter verarbeitet/geprüft wird.

Interessant fand ich nur, dass hier dekompilierte Code-Teile des HMIPServers veröffentlicht wurden.