Ok, habe mir jetzt gerade mal den SSH-Zugang mit root auf der RaspberryMatic eingerichtet.
Hier nun einige Infos.
/var/log/boot.log
Code: Alles auswählen
root@homematic-raspi:/var/log# cat boot.log
fsck 1.47.0 (5-Feb-2023)
userfs: clean, 4958/1867776 files, 176736/7464063 blocks
Starting watchdog...
Identifying host system: Raspberry Pi 4 Model B Rev 1.2 (rpi4), OK
Initializing ZRAM Swap: OK
Initializing RTC Clock: no hardware found
Running sysctl: OK
Checking for Factory Reset: not required
Checking for Backup Restore: not required
Running seedrng: OK
Initializing System: OK
Setup ca-certificates: OK
Starting logging: OK
Starting ArgonONE/FAN daemon: no hardware found
Starting PiDesktop daemon: no hardware found
Populating /dev using udev: done
Init onboard LEDs: init, OK
Starting irqbalance: OK
Starting system message bus: done
Starting iptables: OK
Starting bluetoothd: disabled
Starting network: eth0:... link up, dhcp, firewall, inet up, 192.168.1.7, wlan0: disabled, OK
Starting Network Interface Plugging Daemon: eth0 wlan0.
Starting chrony: OK
Identifying Homematic RF-Hardware: ....HmRF: n/a, HmIP: HM-MOD-RPI-PCB/GPIO@fe201000.serial, OK
Updating Homematic RF-Hardware: HM-MOD-RPI-PCB: 2.8.6, not necessary, OK
Starting hs485dLoader: disabled
Starting xinetd: OK
Starting eq3configd: OK
Starting lighttpd: OK
Starting ser2net: disabled
Starting ssdpd: OK
Starting NUT services: disabled
Starting PIco UPS daemon: no hardware found
Starting PiUSV+ daemon: no hardware found
Starting StromPi2 UPS daemon: disabled
Starting S.USV daemon: no hardware found
Initializing Third-Party Addons: OK
Starting LGWFirmwareUpdate: ...OK
Setting LAN Gateway keys: OK
Starting hs485d: disabled
Starting multimacd: not required
Starting rfd: no BidCos-RF hardware found
Starting HMIPServer: .......................................................................................................................................................ERROR
Starting ReGaHss: .OK
Starting CloudMatic: OK
Starting NeoServer: disabled
Starting Third-Party Addons: OK
Starting crond: OK
Setup onboard LEDs: booted, OK
Finished Boot: 3.75.6.20240316 (raspmatic_rpi4)
/var/log/hmserver.log ist leer.
/var/log/messages
Code: Alles auswählen
root@homematic-raspi:/var/log# cat messages
Jan 1 01:00:09 localhost syslog.info syslogd started: BusyBox v1.36.1
Jan 1 01:00:09 localhost kern.notice kernel: klogd started: BusyBox v1.36.1 (2024-03-16 11:29:00 UTC)
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083]
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.000000] Linux version 6.1.73 (builder@b152b859d874) (aarch64-buildroot-linux-gnu-gcc.br_real (Buildroot -g6d18e07) 12.3.0, GNU ld (GNU Binutils) 2.40) #1 SMP PREEMPT Sat Mar 16 12:41:06 UTC 2024
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.000000] Kernel is locked down from Kernel configuration; see man kernel_lockdown.7
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.000000] random: crng init done
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] Machine model: Raspberry Pi 4 Model B Rev 1.2
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] efi: UEFI not found.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] Reserved memory: created CMA memory pool at 0x000000002ac00000, size 64 MiB
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] Zone ranges:
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] DMA [mem 0x0000000000000000-0x000000003fffffff]
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] DMA32 [mem 0x0000000040000000-0x00000000fbffffff]
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] Normal empty
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] Movable zone start for each node
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] Early memory node ranges
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] node 0: [mem 0x0000000000000000-0x000000003dffffff]
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] node 0: [mem 0x0000000040000000-0x00000000fbffffff]
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000000fbffffff]
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] On node 0, zone DMA32: 8192 pages in unavailable ranges
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] On node 0, zone DMA32: 16384 pages in unavailable ranges
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] percpu: Embedded 28 pages/cpu s75176 r8192 d31320 u114688
Jan 1 01:00:09 localhost kern.debug kernel: [ 0.000000] pcpu-alloc: s75176 r8192 d31320 u114688 alloc=28*4096
Jan 1 01:00:09 localhost kern.debug kernel: [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] Detected PIPT I-cache on CPU0
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] CPU features: detected: Spectre-v2
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] CPU features: detected: Spectre-v3a
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] CPU features: detected: Spectre-v4
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] CPU features: detected: Spectre-BHB
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] CPU features: kernel page table isolation forced ON by KASLR
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] CPU features: detected: Kernel page table isolation (KPTI)
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] CPU features: detected: ARM erratum 1742098
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] alternatives: applying boot alternatives
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1007872
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.000000] Kernel command line: dwc_otg.lpm_enable=0 sdhci_bcm2708.enable_llm=0 console=tty2 root=PARTUUID=deedbeef-02 ro rootfstype=ext4 fsck.repair=yes rootwait rootdelay=5 consoleblank=120 logo.nologo quiet loglevel=0 init_on_alloc=1 init_on_free=1 slab_nomerge iomem=relaxed net.ifnames=0 usb-storage.quirks=174c:55aa:u,2109:0715:u,152d:0578:u,152d:0579:u,152d:1561:u,174c:0829:u,14b0:0206:u,174c:225c:u,7825:a2a4:u,152d:0562:u coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_headphones=0 bcm2708_fb.fbwidth=640 bcm2708_fb.fbheight=480 bcm2708_fb.fbswap=1 smsc95xx.macaddr=DC:A6:32:71:F9:BC vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000 empty
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.000000] Unknown kernel command line parameters "empty", will be passed to user space.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] mem auto-init: stack:all(zero), heap alloc:on, heap free:on
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] mem auto-init: clearing system memory may take some time...
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] software IO TLB: area num 4.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] software IO TLB: mapped [mem 0x000000003a000000-0x000000003e000000] (64MB)
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] Memory: 3854788K/4096000K available (14848K kernel code, 2078K rwdata, 4112K rodata, 4288K init, 1353K bss, 175676K reserved, 65536K cma-reserved)
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] ftrace: allocating 40833 entries in 160 pages
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] ftrace: allocated 160 pages with 2 groups
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.000000] Lockdown: swapper: use of tracefs is restricted; see man kernel_lockdown.7
Jan 1 01:00:09 localhost kern.warn kernel: [ 0.000000] Tracing disabled due to lockdown
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] rcu: Preemptible hierarchical RCU implementation.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] rcu: RCU event tracing is enabled.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] Trampoline variant of Tasks RCU enabled.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] Rude variant of Tasks RCU enabled.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] Tracing variant of Tasks RCU enabled.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] Root IRQ handler: gic_handle_irq
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] GIC: Using split EOI/Deactivate mode
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] arch_timer: cp15 timer(s) running at 54.00MHz (phys).
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xc743ce346, max_idle_ns: 440795203123 ns
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000000] sched_clock: 56 bits at 54MHz, resolution 18ns, wraps every 4398046511102ns
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000328] kfence: initialized - using 2097152 bytes for 255 objects at 0x(____ptrval____)-0x(____ptrval____)
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000479] Console: colour dummy device 80x25
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000537] printk: console [tty2] enabled
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000579] Calibrating delay loop (skipped), value calculated using timer frequency.. 108.00 BogoMIPS (lpj=216000)
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000598] pid_max: default: 32768 minimum: 301
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000742] LSM: Security Framework initializing
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000806] landlock: Up and running.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000812] Yama: becoming mindful.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.000917] AppArmor: AppArmor initialized
Jan 1 01:00:09 localhost kern.info kernel: [ 0.001063] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
Jan 1 01:00:09 localhost kern.info kernel: [ 0.001081] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
Jan 1 01:00:09 localhost kern.info kernel: [ 0.002068] cgroup: Disabling memory control group subsystem
Jan 1 01:00:09 localhost kern.info kernel: [ 0.003619] cblist_init_generic: Setting adjustable number of callback queues.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.003632] cblist_init_generic: Setting shift to 2 and lim to 1.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.003746] cblist_init_generic: Setting adjustable number of callback queues.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.003755] cblist_init_generic: Setting shift to 2 and lim to 1.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.003911] cblist_init_generic: Setting adjustable number of callback queues.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.003920] cblist_init_generic: Setting shift to 2 and lim to 1.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.004171] rcu: Hierarchical SRCU implementation.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.004180] rcu: Max phase no-delay instances is 1000.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.005944] EFI services will not be available.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.006290] smp: Bringing up secondary CPUs ...
Jan 1 01:00:09 localhost kern.info kernel: [ 0.006903] Detected PIPT I-cache on CPU1
Jan 1 01:00:09 localhost kern.info kernel: [ 0.007058] CPU1: Booted secondary processor 0x0000000001 [0x410fd083]
Jan 1 01:00:09 localhost kern.info kernel: [ 0.007754] Detected PIPT I-cache on CPU2
Jan 1 01:00:09 localhost kern.info kernel: [ 0.007881] CPU2: Booted secondary processor 0x0000000002 [0x410fd083]
Jan 1 01:00:09 localhost kern.info kernel: [ 0.008574] Detected PIPT I-cache on CPU3
Jan 1 01:00:09 localhost kern.info kernel: [ 0.008703] CPU3: Booted secondary processor 0x0000000003 [0x410fd083]
Jan 1 01:00:09 localhost kern.info kernel: [ 0.008803] smp: Brought up 1 node, 4 CPUs
Jan 1 01:00:09 localhost kern.info kernel: [ 0.008821] SMP: Total of 4 processors activated.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.008830] CPU features: detected: 32-bit EL0 Support
Jan 1 01:00:09 localhost kern.info kernel: [ 0.008838] CPU features: detected: CRC32 instructions
Jan 1 01:00:09 localhost kern.info kernel: [ 0.008937] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
Jan 1 01:00:09 localhost kern.info kernel: [ 0.008948] CPU: All CPU(s) started at EL2
Jan 1 01:00:09 localhost kern.info kernel: [ 0.008953] alternatives: applying system-wide alternatives
Jan 1 01:00:09 localhost kern.info kernel: [ 0.010898] devtmpfs: initialized
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.021988] Enabled cp15_barrier support
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.022019] Enabled setend support
Jan 1 01:00:09 localhost kern.info kernel: [ 0.022168] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
Jan 1 01:00:09 localhost kern.info kernel: [ 0.022196] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.022300] Lockdown: swapper/0: use of tracefs is restricted; see man kernel_lockdown.7
Jan 1 01:00:09 localhost kern.warn kernel: [ 0.022308] Can not register tracer wakeup due to lockdown
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.022320] Lockdown: swapper/0: use of tracefs is restricted; see man kernel_lockdown.7
Jan 1 01:00:09 localhost kern.warn kernel: [ 0.022327] Can not register tracer function_graph due to lockdown
Jan 1 01:00:09 localhost kern.info kernel: [ 0.054132] pinctrl core: initialized pinctrl subsystem
Jan 1 01:00:09 localhost kern.info kernel: [ 0.054818] DMI not present or invalid.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.055322] NET: Registered PF_NETLINK/PF_ROUTE protocol family
Jan 1 01:00:09 localhost kern.info kernel: [ 0.059057] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations
Jan 1 01:00:09 localhost kern.info kernel: [ 0.059360] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
Jan 1 01:00:09 localhost kern.info kernel: [ 0.060366] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
Jan 1 01:00:09 localhost kern.info kernel: [ 0.060478] audit: initializing netlink subsys (disabled)
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.060720] audit: type=2000 audit(0.060:1): state=initialized audit_enabled=0 res=1
Jan 1 01:00:09 localhost kern.info kernel: [ 0.061257] thermal_sys: Registered thermal governor 'step_wise'
Jan 1 01:00:09 localhost kern.info kernel: [ 0.061320] cpuidle: using governor menu
Jan 1 01:00:09 localhost kern.info kernel: [ 0.061962] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.062097] ASID allocator initialised with 32768 entries
Jan 1 01:00:09 localhost kern.info kernel: [ 0.069534] bcm2835-mbox fe00b880.mailbox: mailbox enabled
Jan 1 01:00:09 localhost kern.info kernel: [ 0.080200] raspberrypi-firmware soc:firmware: Attached to firmware from 2023-10-17T15:39:16, variant start
Jan 1 01:00:09 localhost kern.info kernel: [ 0.084212] raspberrypi-firmware soc:firmware: Firmware hash is 30f0c5e4d076da3ab4f341d88e7d505760b93ad7
Jan 1 01:00:09 localhost kern.info kernel: [ 0.094077] KASLR enabled
Jan 1 01:00:09 localhost kern.info kernel: [ 0.119454] bcm2835-dma fe007000.dma: DMA legacy API manager, dmachans=0x1
Jan 1 01:00:09 localhost kern.info kernel: [ 0.122410] iommu: Default domain type: Translated
Jan 1 01:00:09 localhost kern.info kernel: [ 0.122424] iommu: DMA domain TLB invalidation policy: strict mode
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.122815] SCSI subsystem initialized
Jan 1 01:00:09 localhost kern.info kernel: [ 0.123000] usbcore: registered new interface driver usbfs
Jan 1 01:00:09 localhost kern.info kernel: [ 0.123050] usbcore: registered new interface driver hub
Jan 1 01:00:09 localhost kern.info kernel: [ 0.123091] usbcore: registered new device driver usb
Jan 1 01:00:09 localhost kern.warn kernel: [ 0.123252] usb_phy_generic phy: supply vcc not found, using dummy regulator
Jan 1 01:00:09 localhost kern.info kernel: [ 0.123594] pps_core: LinuxPPS API ver. 1 registered
Jan 1 01:00:09 localhost kern.info kernel: [ 0.123603] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
Jan 1 01:00:09 localhost kern.info kernel: [ 0.123623] PTP clock support registered
Jan 1 01:00:09 localhost kern.info kernel: [ 0.124681] vgaarb: loaded
Jan 1 01:00:09 localhost kern.info kernel: [ 0.125539] clocksource: Switched to clocksource arch_sys_counter
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.125555] Lockdown: swapper/0: use of tracefs is restricted; see man kernel_lockdown.7
Jan 1 01:00:09 localhost kern.warn kernel: [ 0.125563] Tracing disabled due to lockdown
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.125570] Lockdown: swapper/0: use of tracefs is restricted; see man kernel_lockdown.7
Jan 1 01:00:09 localhost kern.warn kernel: [ 0.125577] Tracing disabled due to lockdown
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.125588] Lockdown: swapper/0: use of tracefs is restricted; see man kernel_lockdown.7
Jan 1 01:00:09 localhost kern.warn kernel: [ 0.125594] Tracing disabled due to lockdown
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.125603] Lockdown: swapper/0: use of tracefs is restricted; see man kernel_lockdown.7
Jan 1 01:00:09 localhost kern.warn kernel: [ 0.125610] Tracing disabled due to lockdown
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.125616] Lockdown: swapper/0: use of tracefs is restricted; see man kernel_lockdown.7
Jan 1 01:00:09 localhost kern.warn kernel: [ 0.125622] Tracing disabled due to lockdown
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.125976] VFS: Disk quotas dquot_6.6.0
Jan 1 01:00:09 localhost kern.info kernel: [ 0.126032] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.126131] FS-Cache: Loaded
Jan 1 01:00:09 localhost kern.info kernel: [ 0.126282] CacheFiles: Loaded
Jan 1 01:00:09 localhost kern.info kernel: [ 0.126791] AppArmor: AppArmor Filesystem Enabled
Jan 1 01:00:09 localhost kern.info kernel: [ 0.136046] NET: Registered PF_INET protocol family
Jan 1 01:00:09 localhost kern.info kernel: [ 0.136194] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
Jan 1 01:00:09 localhost kern.info kernel: [ 0.141084] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
Jan 1 01:00:09 localhost kern.info kernel: [ 0.141140] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
Jan 1 01:00:09 localhost kern.info kernel: [ 0.141181] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
Jan 1 01:00:09 localhost kern.info kernel: [ 0.141372] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear)
Jan 1 01:00:09 localhost kern.info kernel: [ 0.142378] TCP: Hash tables configured (established 32768 bind 32768)
Jan 1 01:00:09 localhost kern.info kernel: [ 0.142700] MPTCP token hash table entries: 4096 (order: 4, 98304 bytes, linear)
Jan 1 01:00:09 localhost kern.info kernel: [ 0.142886] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
Jan 1 01:00:09 localhost kern.info kernel: [ 0.142938] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
Jan 1 01:00:09 localhost kern.info kernel: [ 0.143182] NET: Registered PF_UNIX/PF_LOCAL protocol family
Jan 1 01:00:09 localhost kern.info kernel: [ 0.143869] RPC: Registered named UNIX socket transport module.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.143882] RPC: Registered udp transport module.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.143888] RPC: Registered tcp transport module.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.143893] RPC: Registered tcp NFSv4.1 backchannel transport module.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.143908] PCI: CLS 0 bytes, default 64
Jan 1 01:00:09 localhost kern.info kernel: [ 0.146175] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.147218] Lockdown: swapper/0: use of tracefs is restricted; see man kernel_lockdown.7
Jan 1 01:00:09 localhost kern.warn kernel: [ 0.147231] Tracing disabled due to lockdown
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.147240] Lockdown: swapper/0: use of tracefs is restricted; see man kernel_lockdown.7
Jan 1 01:00:09 localhost kern.warn kernel: [ 0.147247] Can not register tracer blk due to lockdown
Jan 1 01:00:09 localhost kern.warn kernel: [ 0.147253] blktrace: Warning: could not register the block tracer
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.147578] Initialise system trusted keyrings
Jan 1 01:00:09 localhost kern.info kernel: [ 0.147816] workingset: timestamp_bits=46 max_order=20 bucket_order=0
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.159407] NFS: Registering the id_resolver key type
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.159461] Key type id_resolver registered
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.159469] Key type id_legacy registered
Jan 1 01:00:09 localhost kern.info kernel: [ 0.159572] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
Jan 1 01:00:09 localhost kern.info kernel: [ 0.159594] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
Jan 1 01:00:09 localhost kern.info kernel: [ 0.159632] ntfs: driver 2.1.32 [Flags: R/W].
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.161862] Key type asymmetric registered
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.161876] Asymmetric key parser 'x509' registered
Jan 1 01:00:09 localhost kern.info kernel: [ 0.161952] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
Jan 1 01:00:09 localhost kern.info kernel: [ 0.162194] io scheduler mq-deadline registered
Jan 1 01:00:09 localhost kern.info kernel: [ 0.162205] io scheduler kyber registered
Jan 1 01:00:09 localhost kern.info kernel: [ 0.167766] brcm-pcie fd500000.pcie: host bridge /scb/pcie@7d500000 ranges:
Jan 1 01:00:09 localhost kern.info kernel: [ 0.167800] brcm-pcie fd500000.pcie: No bus range found for /scb/pcie@7d500000, using [bus 00-ff]
Jan 1 01:00:09 localhost kern.info kernel: [ 0.167840] brcm-pcie fd500000.pcie: MEM 0x0600000000..0x063fffffff -> 0x00c0000000
Jan 1 01:00:09 localhost kern.info kernel: [ 0.167877] brcm-pcie fd500000.pcie: IB MEM 0x0000000000..0x00bfffffff -> 0x0400000000
Jan 1 01:00:09 localhost kern.info kernel: [ 0.168389] brcm-pcie fd500000.pcie: setting SCB_ACCESS_EN, READ_UR_MODE, MAX_BURST_SIZE
Jan 1 01:00:09 localhost kern.info kernel: [ 0.168710] brcm-pcie fd500000.pcie: PCI host bridge to bus 0000:00
Jan 1 01:00:09 localhost kern.info kernel: [ 0.168727] pci_bus 0000:00: root bus resource [bus 00-ff]
Jan 1 01:00:09 localhost kern.info kernel: [ 0.168742] pci_bus 0000:00: root bus resource [mem 0x600000000-0x63fffffff] (bus address [0xc0000000-0xffffffff])
Jan 1 01:00:09 localhost kern.info kernel: [ 0.168785] pci 0000:00:00.0: [14e4:2711] type 01 class 0x060400
Jan 1 01:00:09 localhost kern.info kernel: [ 0.168873] pci 0000:00:00.0: PME# supported from D0 D3hot
Jan 1 01:00:09 localhost kern.warn kernel: [ 0.172816] pci_bus 0000:01: supply vpcie3v3 not found, using dummy regulator
Jan 1 01:00:09 localhost kern.warn kernel: [ 0.172956] pci_bus 0000:01: supply vpcie3v3aux not found, using dummy regulator
Jan 1 01:00:09 localhost kern.warn kernel: [ 0.173015] pci_bus 0000:01: supply vpcie12v not found, using dummy regulator
Jan 1 01:00:09 localhost kern.info kernel: [ 0.279627] brcm-pcie fd500000.pcie: link up, 5.0 GT/s PCIe x1 (SSC)
Jan 1 01:00:09 localhost kern.info kernel: [ 0.279809] pci 0000:01:00.0: [1106:3483] type 00 class 0x0c0330
Jan 1 01:00:09 localhost kern.info kernel: [ 0.279902] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00000fff 64bit]
Jan 1 01:00:09 localhost kern.info kernel: [ 0.280184] pci 0000:01:00.0: PME# supported from D0 D3cold
Jan 1 01:00:09 localhost kern.info kernel: [ 0.289647] pci 0000:00:00.0: BAR 8: assigned [mem 0x600000000-0x6000fffff]
Jan 1 01:00:09 localhost kern.info kernel: [ 0.289671] pci 0000:01:00.0: BAR 0: assigned [mem 0x600000000-0x600000fff 64bit]
Jan 1 01:00:09 localhost kern.info kernel: [ 0.289732] pci 0000:00:00.0: PCI bridge to [bus 01]
Jan 1 01:00:09 localhost kern.info kernel: [ 0.289744] pci 0000:00:00.0: bridge window [mem 0x600000000-0x6000fffff]
Jan 1 01:00:09 localhost kern.info kernel: [ 0.289967] pcieport 0000:00:00.0: enabling device (0000 -> 0002)
Jan 1 01:00:09 localhost kern.info kernel: [ 0.290112] pcieport 0000:00:00.0: PME: Signaling with IRQ 30
Jan 1 01:00:09 localhost kern.info kernel: [ 0.290422] pcieport 0000:00:00.0: AER: enabled with IRQ 30
Jan 1 01:00:09 localhost kern.info kernel: [ 0.291173] simple-framebuffer 3ea9b000.framebuffer: framebuffer at 0x3ea9b000, 0x12c000 bytes
Jan 1 01:00:09 localhost kern.info kernel: [ 0.291189] simple-framebuffer 3ea9b000.framebuffer: format=a8r8g8b8, mode=640x480x32, linelength=2560
Jan 1 01:00:09 localhost kern.info kernel: [ 0.291618] Console: switching to colour frame buffer device 80x30
Jan 1 01:00:09 localhost kern.info kernel: [ 0.292902] simple-framebuffer 3ea9b000.framebuffer: fb0: simplefb registered!
Jan 1 01:00:09 localhost kern.info kernel: [ 0.297312] Serial: 8250/16550 driver, 1 ports, IRQ sharing enabled
Jan 1 01:00:09 localhost kern.info kernel: [ 0.299071] iproc-rng200 fe104000.rng: hwrng registered
Jan 1 01:00:09 localhost kern.info kernel: [ 0.299307] vc-mem: phys_addr:0x00000000 mem_base=0x3ec00000 mem_size:0x40000000(1024 MiB)
Jan 1 01:00:09 localhost kern.info kernel: [ 0.310041] brd: module loaded
Jan 1 01:00:09 localhost kern.info kernel: [ 0.316234] loop: module loaded
Jan 1 01:00:09 localhost kern.info kernel: [ 0.316736] zram: Added device: zram0
Jan 1 01:00:09 localhost kern.info kernel: [ 0.317310] Loading iSCSI transport class v2.0-870.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.320628] tun: Universal TUN/TAP device driver, 1.6
Jan 1 01:00:09 localhost kern.info kernel: [ 0.321595] bcmgenet fd580000.ethernet: GENET 5.0 EPHY: 0x0000
Jan 1 01:00:09 localhost kern.info kernel: [ 0.421665] unimac-mdio unimac-mdio.-19: Broadcom UniMAC MDIO bus
Jan 1 01:00:09 localhost kern.info kernel: [ 0.423870] xhci_hcd 0000:01:00.0: enabling device (0000 -> 0002)
Jan 1 01:00:09 localhost kern.info kernel: [ 0.423945] xhci_hcd 0000:01:00.0: xHCI Host Controller
Jan 1 01:00:09 localhost kern.info kernel: [ 0.423974] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 1
Jan 1 01:00:09 localhost kern.info kernel: [ 0.424537] xhci_hcd 0000:01:00.0: hcc params 0x002841eb hci version 0x100 quirks 0x0b00040000000890
Jan 1 01:00:09 localhost kern.info kernel: [ 0.425016] xhci_hcd 0000:01:00.0: xHCI Host Controller
Jan 1 01:00:09 localhost kern.info kernel: [ 0.425036] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
Jan 1 01:00:09 localhost kern.info kernel: [ 0.425053] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed
Jan 1 01:00:09 localhost kern.info kernel: [ 0.425304] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
Jan 1 01:00:09 localhost kern.info kernel: [ 0.425322] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Jan 1 01:00:09 localhost kern.info kernel: [ 0.425333] usb usb1: Product: xHCI Host Controller
Jan 1 01:00:09 localhost kern.info kernel: [ 0.425343] usb usb1: Manufacturer: Linux 6.1.73 xhci-hcd
Jan 1 01:00:09 localhost kern.info kernel: [ 0.425352] usb usb1: SerialNumber: 0000:01:00.0
Jan 1 01:00:09 localhost kern.info kernel: [ 0.425913] hub 1-0:1.0: USB hub found
Jan 1 01:00:09 localhost kern.info kernel: [ 0.425988] hub 1-0:1.0: 1 port detected
Jan 1 01:00:09 localhost kern.info kernel: [ 0.426669] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01
Jan 1 01:00:09 localhost kern.info kernel: [ 0.426686] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Jan 1 01:00:09 localhost kern.info kernel: [ 0.426697] usb usb2: Product: xHCI Host Controller
Jan 1 01:00:09 localhost kern.info kernel: [ 0.426706] usb usb2: Manufacturer: Linux 6.1.73 xhci-hcd
Jan 1 01:00:09 localhost kern.info kernel: [ 0.426715] usb usb2: SerialNumber: 0000:01:00.0
Jan 1 01:00:09 localhost kern.info kernel: [ 0.427200] hub 2-0:1.0: USB hub found
Jan 1 01:00:09 localhost kern.info kernel: [ 0.427270] hub 2-0:1.0: 4 ports detected
Jan 1 01:00:09 localhost kern.info kernel: [ 0.428315] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
Jan 1 01:00:09 localhost kern.debug kernel: [ 0.428418] dwc_otg: FIQ enabled
Jan 1 01:00:09 localhost kern.debug kernel: [ 0.428425] dwc_otg: NAK holdoff enabled
Jan 1 01:00:09 localhost kern.debug kernel: [ 0.428431] dwc_otg: FIQ split-transaction FSM enabled
Jan 1 01:00:09 localhost kern.debug kernel: [ 0.428445] Module dwc_common_port init
Jan 1 01:00:09 localhost kern.info kernel: [ 0.429098] usbcore: registered new interface driver uas
Jan 1 01:00:09 localhost kern.info kernel: [ 0.429174] usbcore: registered new interface driver usb-storage
Jan 1 01:00:09 localhost kern.info kernel: [ 0.429267] usbcore: registered new interface driver usbserial_generic
Jan 1 01:00:09 localhost kern.info kernel: [ 0.429295] usbserial: USB Serial support registered for generic
Jan 1 01:00:09 localhost kern.info kernel: [ 0.429731] Driver for 1-wire Dallas network protocol.
Jan 1 01:00:09 localhost kern.info kernel: [ 0.431061] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com
Jan 1 01:00:09 localhost kern.info kernel: [ 0.433282] sdhci: Secure Digital Host Controller Interface driver
Jan 1 01:00:09 localhost kern.info kernel: [ 0.433296] sdhci: Copyright(c) Pierre Ossman
Jan 1 01:00:09 localhost kern.err kernel: [ 0.433500] Error: Driver 'sdhost-bcm2835' is already registered, aborting...
Jan 1 01:00:09 localhost kern.info kernel: [ 0.433510] sdhci-pltfm: SDHCI platform and OF driver helper
Jan 1 01:00:09 localhost kern.info kernel: [ 0.436826] ledtrig-cpu: registered to indicate activity on CPUs
Jan 1 01:00:09 localhost kern.info kernel: [ 0.436929] hid: raw HID events driver (C) Jiri Kosina
Jan 1 01:00:09 localhost kern.info kernel: [ 0.437070] usbcore: registered new interface driver usbhid
Jan 1 01:00:09 localhost kern.info kernel: [ 0.437074] usbhid: USB HID core driver
Jan 1 01:00:09 localhost kern.info kernel: [ 0.442737] NET: Registered PF_INET6 protocol family
Jan 1 01:00:09 localhost kern.info kernel: [ 0.443566] Segment Routing with IPv6
Jan 1 01:00:09 localhost kern.info kernel: [ 0.443586] In-situ OAM (IOAM) with IPv6
Jan 1 01:00:09 localhost kern.info kernel: [ 0.443671] NET: Registered PF_PACKET protocol family
Jan 1 01:00:09 localhost kern.info kernel: [ 0.443714] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.443763] Key type dns_resolver registered
Jan 1 01:00:09 localhost kern.info kernel: [ 0.444458] registered taskstats version 1
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.444493] Loading compiled-in X.509 certificates
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.446715] Loaded X.509 cert 'Build time autogenerated kernel key: c62db4b3a5b1783de6b17d82c07d95988e324b19'
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.446939] Key type .fscrypt registered
Jan 1 01:00:09 localhost kern.notice kernel: [ 0.446945] Key type fscrypt-provisioning registered
Jan 1 01:00:09 localhost kern.info kernel: [ 0.447072] AppArmor: AppArmor sha1 policy hashing enabled
Jan 1 01:00:09 localhost kern.info kernel: [ 0.458106] fe215040.serial: ttyS0 at MMIO 0xfe215040 (irq = 35, base_baud = 62500000) is a 16550
Jan 1 01:00:09 localhost kern.info kernel: [ 0.458669] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer
Jan 1 01:00:09 localhost kern.info kernel: [ 0.458795] bcm2835-power bcm2835-power: Broadcom BCM2835 power domains driver
Jan 1 01:00:09 localhost kern.info kernel: [ 0.459194] mmc-bcm2835 fe300000.mmcnr: mmc_debug:0 mmc_debug2:0
Jan 1 01:00:09 localhost kern.info kernel: [ 0.459202] mmc-bcm2835 fe300000.mmcnr: DMA channel allocated
Jan 1 01:00:09 localhost kern.info kernel: [ 0.486581] of_cfs_init
Jan 1 01:00:09 localhost kern.info kernel: [ 0.486727] of_cfs_init: OK
Jan 1 01:00:09 localhost kern.info kernel: [ 0.487834] Waiting 5 sec before mounting root device...
Jan 1 01:00:09 localhost kern.info kernel: [ 0.521617] mmc0: SDHCI controller on fe340000.mmc [fe340000.mmc] using ADMA
Jan 1 01:00:09 localhost kern.info kernel: [ 0.566197] mmc1: new high speed SDIO card at address 0001
Jan 1 01:00:09 localhost kern.info kernel: [ 0.621742] mmc0: new ultra high speed DDR50 SDHC card at address aaaa
Jan 1 01:00:09 localhost kern.info kernel: [ 0.622182] mmcblk0: mmc0:aaaa SH32G 29.7 GiB
Jan 1 01:00:09 localhost kern.info kernel: [ 0.623811] mmcblk0: p1 p2 p3
Jan 1 01:00:09 localhost kern.info kernel: [ 0.624147] mmcblk0: mmc0:aaaa SH32G 29.7 GiB (quirks 0x00004000)
Jan 1 01:00:09 localhost kern.info kernel: [ 0.681557] usb 1-1: new high-speed USB device number 2 using xhci_hcd
Jan 1 01:00:09 localhost kern.info kernel: [ 0.832204] usb 1-1: New USB device found, idVendor=2109, idProduct=3431, bcdDevice= 4.21
Jan 1 01:00:09 localhost kern.info kernel: [ 0.832224] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
Jan 1 01:00:09 localhost kern.info kernel: [ 0.832236] usb 1-1: Product: USB2.0 Hub
Jan 1 01:00:09 localhost kern.info kernel: [ 0.833652] hub 1-1:1.0: USB hub found
Jan 1 01:00:09 localhost kern.info kernel: [ 0.833941] hub 1-1:1.0: 4 ports detected
Jan 1 01:00:09 localhost kern.info kernel: [ 1.129576] usb 1-1.3: new full-speed USB device number 3 using xhci_hcd
Jan 1 01:00:09 localhost kern.info kernel: [ 1.238621] usb 1-1.3: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
Jan 1 01:00:09 localhost kern.info kernel: [ 1.238640] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
Jan 1 01:00:09 localhost kern.info kernel: [ 1.238651] usb 1-1.3: Product: ConBee II
Jan 1 01:00:09 localhost kern.info kernel: [ 1.238660] usb 1-1.3: Manufacturer: dresden elektronik ingenieurtechnik GmbH
Jan 1 01:00:09 localhost kern.info kernel: [ 1.238670] usb 1-1.3: SerialNumber: DE2193845
Jan 1 01:00:09 localhost kern.info kernel: [ 5.630919] EXT4-fs (mmcblk0p2): orphan cleanup on readonly fs
Jan 1 01:00:09 localhost kern.info kernel: [ 5.631278] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Quota mode: none.
Jan 1 01:00:09 localhost kern.info kernel: [ 5.631353] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
Jan 1 01:00:09 localhost kern.info kernel: [ 5.631875] devtmpfs: mounted
Jan 1 01:00:09 localhost kern.info kernel: [ 5.639667] Freeing unused kernel memory: 4288K
Jan 1 01:00:09 localhost kern.info kernel: [ 5.678784] Checked W+X mappings: passed, no W+X pages found
Jan 1 01:00:09 localhost kern.info kernel: [ 5.678817] Run /sbin/init as init process
Jan 1 01:00:09 localhost kern.debug kernel: [ 5.678821] with arguments:
Jan 1 01:00:09 localhost kern.debug kernel: [ 5.678823] /sbin/init
Jan 1 01:00:09 localhost kern.debug kernel: [ 5.678825] empty
Jan 1 01:00:09 localhost kern.debug kernel: [ 5.678828] with environment:
Jan 1 01:00:09 localhost kern.debug kernel: [ 5.678830] HOME=/
Jan 1 01:00:09 localhost kern.debug kernel: [ 5.678832] TERM=linux
Jan 1 01:00:09 localhost kern.err kernel: [ 6.045436] EXT4-fs: Mount option(s) incompatible with ext2
Jan 1 01:00:09 localhost kern.info kernel: [ 6.262904] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Quota mode: none.
Jan 1 01:00:09 localhost kern.info kernel: [ 7.320159] zram: Added device: zram1
Jan 1 01:00:09 localhost kern.info kernel: [ 7.322897] zram1: detected capacity change from 0 to 8241688
Jan 1 01:00:09 localhost kern.info kernel: [ 7.348676] Adding 4120840k swap on /dev/zram1. Priority:75 extents:1 across:4120840k SS
Jan 1 01:00:09 localhost kern.info kernel: [ 7.403576] i2c_dev: i2c /dev entries driver
Jan 1 01:00:09 localhost daemon.info kernel: [ 9.603180] udevd[1041]: starting version 3.2.14
Jan 1 01:00:09 localhost daemon.info kernel: [ 9.634755] udevd[1042]: starting eudev-3.2.14
Jan 1 01:00:09 localhost kern.info kernel: [ 9.800669] rpi-gpiomem fe200000.gpiomem: window base 0xfe200000 size 0x00001000
Jan 1 01:00:09 localhost kern.info kernel: [ 9.800820] rpi-gpiomem fe200000.gpiomem: initialised 1 regions as /dev/gpiomem
Jan 1 01:00:09 localhost kern.warn kernel: [ 9.806866] generic_raw_uart: loading out-of-tree module taints kernel.
Jan 1 01:00:09 localhost kern.warn kernel: [ 9.813357] vc_sm_cma: module is from the staging directory, the quality is unknown, you have been warned.
Jan 1 01:00:09 localhost kern.info kernel: [ 9.814966] bcm2835_vc_sm_cma_probe: Videocore shared memory driver
Jan 1 01:00:09 localhost kern.info kernel: [ 9.814989] [vc_sm_connected_init]: start
Jan 1 01:00:09 localhost kern.info kernel: [ 9.815744] [vc_sm_connected_init]: installed successfully
Jan 1 01:00:09 localhost kern.info kernel: [ 9.834185] pl011_raw_uart fe201000.serial: there is not valid maps for state default
Jan 1 01:00:09 localhost kern.info kernel: [ 9.834374] pl011_raw_uart fe201000.serial: Initialized pl011 device; mapbase=0xfe201000; irq=39; clockrate=48000001
Jan 1 01:00:09 localhost kern.info kernel: [ 9.834437] pl011_raw_uart fe201000.serial: Missing I2C driver of rtc device, trying to load
Jan 1 01:00:09 localhost kern.info kernel: [ 9.834442] pl011_raw_uart fe201000.serial: Requesting module i2c:rx8130
Jan 1 01:00:09 localhost kern.warn kernel: [ 9.843380] rtc-ds1307: probe of 1-0032 failed with error -5
Jan 1 01:00:09 localhost kern.warn kernel: [ 9.846550] rtc-ds1307: probe of 1-0032 failed with error -5
Jan 1 01:00:09 localhost kern.info kernel: [ 9.846903] raw-uart raw-uart: Reset radio module
Jan 1 01:00:09 localhost kern.info kernel: [ 9.897484] cdc_acm 1-1.3:1.0: ttyACM0: USB ACM device
Jan 1 01:00:09 localhost kern.info kernel: [ 9.897609] usbcore: registered new interface driver cdc_acm
Jan 1 01:00:09 localhost kern.info kernel: [ 9.897616] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
Jan 1 01:00:09 localhost kern.notice kernel: [ 9.960310] cfg80211: Loading compiled-in X.509 certificates for regulatory database
Jan 1 01:00:09 localhost kern.notice kernel: [ 9.968573] cfg80211: Loaded X.509 cert 'benh@debian.org: 577e021cb980e0e820821ba7b54b4961b8b4fadf'
Jan 1 01:00:09 localhost kern.notice kernel: [ 9.968994] cfg80211: Loaded X.509 cert 'romain.perier@gmail.com: 3abbc6ec146e09d1b6016ab9d6cf71dd233f0328'
Jan 1 01:00:09 localhost kern.notice kernel: [ 9.969389] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
Jan 1 01:00:09 localhost kern.notice kernel: [ 9.969840] cfg80211: Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600'
Jan 1 01:00:10 localhost kern.debug kernel: [ 10.012433] brcmfmac: F1 signature read @0x18000000=0x15264345
Jan 1 01:00:10 localhost kern.info kernel: [ 10.016083] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
Jan 1 01:00:10 localhost kern.info kernel: [ 10.016486] usbcore: registered new interface driver brcmfmac
Jan 1 01:00:10 localhost kern.info kernel: [ 10.029550] raw-uart raw-uart: Registered new raw-uart device using underlying device GPIO@fe201000.serial.
Jan 1 01:00:10 localhost daemon.debug /usr/sbin/irqbalance: IRQ arch_timer(11) guessed as class 0
Jan 1 01:00:10 localhost daemon.debug /usr/sbin/irqbalance: IRQ fe00b880.mailbox(14) guessed as class 0
Jan 1 01:00:10 localhost daemon.debug /usr/sbin/irqbalance: IRQ DMA IRQ(15) guessed as class 0
Jan 1 01:00:10 localhost daemon.debug /usr/sbin/irqbalance: IRQ DMA IRQ(16) guessed as class 0
Jan 1 01:00:10 localhost daemon.debug /usr/sbin/irqbalance: IRQ DMA IRQ(17) guessed as class 0
Jan 1 01:00:10 localhost daemon.debug /usr/sbin/irqbalance: IRQ arm-pmu(23) guessed as class 0
Jan 1 01:00:10 localhost daemon.debug /usr/sbin/irqbalance: IRQ arm-pmu(24) guessed as class 0
Jan 1 01:00:10 localhost daemon.debug /usr/sbin/irqbalance: IRQ arm-pmu(25) guessed as class 0
Jan 1 01:00:10 localhost daemon.debug /usr/sbin/irqbalance: IRQ arm-pmu(26) guessed as class 0
Jan 1 01:00:10 localhost daemon.debug /usr/sbin/irqbalance: IRQ PCIe PME, aerdrv(30) guessed as class 0
Jan 1 01:00:10 localhost daemon.debug /usr/sbin/irqbalance: IRQ xhci_hcd(33) guessed as class 0
Jan 1 01:00:10 localhost daemon.debug /usr/sbin/irqbalance: IRQ VCHIQ doorbell(34) guessed as class 0
Jan 1 01:00:10 localhost daemon.debug /usr/sbin/irqbalance: IRQ mmc1, mmc0(36) guessed as class 0
Jan 1 01:00:10 localhost daemon.debug /usr/sbin/irqbalance: IRQ fe804000.i2c(37) guessed as class 0
Jan 1 01:00:10 localhost daemon.debug /usr/sbin/irqbalance: IRQ fe204000.spi(38) guessed as class 0
Jan 1 01:00:10 localhost user.notice rfkill: block set for type bluetooth
Jan 1 01:00:10 localhost kern.info kernel: [ 10.236498] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Nov 1 2021 00:37:25 version 7.45.241 (1a2f2fa CY) FWID 01-703fd60
Jan 1 01:00:10 localhost kern.info kernel: [ 10.297300] bcmgenet fd580000.ethernet: configuring instance for external RGMII (RX delay)
Jan 1 01:00:10 localhost kern.info kernel: [ 10.298127] bcmgenet fd580000.ethernet eth0: Link is Down
Jan 1 01:00:14 localhost kern.info kernel: [ 14.397791] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Jan 1 01:00:14 localhost kern.info kernel: [ 14.398269] bcmgenet fd580000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
Jan 1 01:00:16 localhost syslog.info syslogd exiting
Jan 1 01:00:16 homematic-raspi syslog.info syslogd started: BusyBox v1.36.1
Jan 1 01:00:16 homematic-raspi kern.notice kernel: klogd started: BusyBox v1.36.1 (2024-03-16 11:29:00 UTC)
Jan 1 01:00:16 homematic-raspi daemon.info udhcpc[1153]: started, v1.36.1
Jan 1 01:00:16 homematic-raspi daemon.info udhcpc[1153]: broadcasting discover
Jan 1 01:00:16 homematic-raspi daemon.info udhcpc[1153]: broadcasting select for 192.168.1.7, server 192.168.1.1
Jan 1 01:00:16 homematic-raspi daemon.info udhcpc[1153]: lease of 192.168.1.7 obtained from 192.168.1.1, lease time 864000
Jan 1 01:00:17 homematic-raspi user.info firewall: configuration set
Jan 1 01:00:17 homematic-raspi user.notice rfkill: block set for type wlan
Jan 1 01:00:17 homematic-raspi daemon.info ifplugd(eth0)[1301]: ifplugd 0.28 initializing.
Jan 1 01:00:17 homematic-raspi daemon.info ifplugd(eth0)[1301]: Using interface eth0/DC:A6:32:71:F9:BC with driver <bcmgenet> (version: 6.1.73)
Jan 1 01:00:17 homematic-raspi daemon.info ifplugd(eth0)[1301]: Using detection mode: SIOCETHTOOL
Jan 1 01:00:17 homematic-raspi daemon.info ifplugd(eth0)[1301]: Initialization complete, link beat detected.
Jan 1 01:00:17 homematic-raspi daemon.info ifplugd(eth0)[1301]: Executing '/etc/ifplugd/ifplugd.action eth0 up'.
Jan 1 01:00:17 homematic-raspi daemon.warn ifplugd(eth0)[1301]: client: ifup: interface eth0 already configured
Jan 1 01:00:17 homematic-raspi daemon.info ifplugd(eth0)[1301]: Program executed successfully.
Jan 1 01:00:17 homematic-raspi daemon.info ifplugd(wlan0)[1306]: ifplugd 0.28 initializing.
Jan 1 01:00:17 homematic-raspi daemon.info ifplugd(wlan0)[1306]: Using interface wlan0/DC:A6:32:71:F9:BD with driver <brcmfmac> (version: 7.45.241)
Jan 1 01:00:17 homematic-raspi daemon.info ifplugd(wlan0)[1306]: Using detection mode: wireless extension
Jan 1 01:00:17 homematic-raspi daemon.info ifplugd(wlan0)[1306]: Initialization complete, link beat not detected.
Jan 1 01:00:20 homematic-raspi daemon.debug /usr/sbin/irqbalance: IRQ eth0(31) guessed as class 5
Jan 1 01:00:20 homematic-raspi daemon.debug /usr/sbin/irqbalance: IRQ eth0(32) guessed as class 5
Jan 1 01:00:20 homematic-raspi daemon.warn /usr/sbin/irqbalance: Cannot change IRQ 23 affinity: Input/output error
Jan 1 01:00:20 homematic-raspi daemon.warn /usr/sbin/irqbalance: IRQ 23 affinity is now unmanaged
Jan 1 01:00:20 homematic-raspi daemon.warn /usr/sbin/irqbalance: Cannot change IRQ 24 affinity: Input/output error
Jan 1 01:00:20 homematic-raspi daemon.warn /usr/sbin/irqbalance: IRQ 24 affinity is now unmanaged
Jan 1 01:00:20 homematic-raspi daemon.warn /usr/sbin/irqbalance: Cannot change IRQ 25 affinity: Input/output error
Jan 1 01:00:20 homematic-raspi daemon.warn /usr/sbin/irqbalance: IRQ 25 affinity is now unmanaged
Jan 1 01:00:20 homematic-raspi daemon.warn /usr/sbin/irqbalance: Cannot change IRQ 26 affinity: Input/output error
Jan 1 01:00:20 homematic-raspi daemon.warn /usr/sbin/irqbalance: IRQ 26 affinity is now unmanaged
Apr 2 20:26:50 homematic-raspi daemon.notice ntpdate[1312]: step time server 185.13.148.71 offset +1712082382.260332 sec
Apr 2 20:26:50 homematic-raspi daemon.info chronyd[1315]: chronyd version 4.4 starting (+CMDMON +NTP +REFCLOCK +RTC +PRIVDROP -SCFILTER -SIGND +ASYNCDNS -NTS -SECHASH +IPV6 -DEBUG)
Apr 2 20:26:50 homematic-raspi daemon.info chronyd[1315]: Added source 192.168.1.1
Apr 2 20:26:50 homematic-raspi daemon.info chronyd[1315]: Added source ID#0000000001 (0.de.pool.ntp.org)
Apr 2 20:26:50 homematic-raspi daemon.info chronyd[1315]: Added source ID#0000000002 (1.de.pool.ntp.org)
Apr 2 20:26:50 homematic-raspi daemon.info chronyd[1315]: Added source ID#0000000003 (2.de.pool.ntp.org)
Apr 2 20:26:50 homematic-raspi daemon.info chronyd[1315]: Added source ID#0000000004 (3.de.pool.ntp.org)
Apr 2 20:26:50 homematic-raspi kern.info kernel: [ 27.992308] raw-uart raw-uart: Reset radio module
Apr 2 20:26:52 homematic-raspi kern.info kernel: [ 30.210842] raw-uart raw-uart: Reset radio module
Apr 2 20:26:56 homematic-raspi kern.info kernel: [ 34.277203] raw-uart raw-uart: Reset radio module
Apr 2 20:26:56 homematic-raspi daemon.err xinetd[1424]: Unable to read included directory: /etc/config/xinetd.d [file=/etc/xinetd.conf] [line=14]
Apr 2 20:26:56 homematic-raspi daemon.crit xinetd[1424]: 1424 {init_services} no services. Exiting...
Apr 2 20:27:02 homematic-raspi daemon.debug /usr/sbin/irqbalance: IRQ (39) guessed as class 0
Apr 2 20:27:58 homematic-raspi daemon.info chronyd[1315]: Selected source 192.168.1.1
Apr 2 18:32:01 homematic-raspi daemon.info : starting pid 1816, tty '': '/bin/mv /tmp/boot.log /var/log/boot.log'
Apr 2 18:32:01 homematic-raspi daemon.info : starting pid 1817, tty '/dev/null': '/usr/bin/monit -Ic /etc/monitrc'
Apr 2 20:32:01 homematic-raspi user.info monit[1817]: Starting Monit 5.33.0 daemon with http interface at /var/run/monit.sock
Apr 2 20:32:01 homematic-raspi user.info monit[1817]: 'homematic-raspi' Monit 5.33.0 started
Apr 2 20:32:04 homematic-raspi local0.err ReGaHss: ERROR: XmlRpc: Error in XmlRpcClient::writeRequest: write error (error 111). [error():iseXmlRpc.h:281]
Apr 2 20:32:04 homematic-raspi local0.warn ReGaHss: WARNING: XMLRPC 'init': rpcClient.execute() failed (url: xmlrpc://127.0.0.1:39292/groups, params: {"xmlrpc_bin://127.0.0.1:31999","1007"}, result: nil) [CallXmlrpcMethod():iseXmlRpc.cpp:2612]
Apr 2 20:32:04 homematic-raspi local0.err ReGaHss: ERROR: XMLRPC 'init' call failed (interface: 1007, params: {"xmlrpc_bin://127.0.0.1:31999","1007"}) [CallInit():iseXmlRpc.cpp:1214]
Apr 2 20:32:04 homematic-raspi local0.err ReGaHss: ERROR: failed CallInit() for interface=VirtualDevices [ThreadFunction():iseRTHss.cpp:163]
Apr 2 20:32:04 homematic-raspi local0.err ReGaHss: ERROR: XmlRpc: Error in XmlRpcClient::writeRequest: write error (error 111). [error():iseXmlRpc.h:281]
Apr 2 20:32:04 homematic-raspi local0.warn ReGaHss: WARNING: XMLRPC 'init': rpcClient.execute() failed (url: xmlrpc://127.0.0.1:32010, params: {"xmlrpc_bin://127.0.0.1:31999","1008"}, result: nil) [CallXmlrpcMethod():iseXmlRpc.cpp:2612]
Apr 2 20:32:04 homematic-raspi local0.err ReGaHss: ERROR: XMLRPC 'init' call failed (interface: 1008, params: {"xmlrpc_bin://127.0.0.1:31999","1008"}) [CallInit():iseXmlRpc.cpp:1214]
Apr 2 20:32:04 homematic-raspi local0.err ReGaHss: ERROR: failed CallInit() for interface=HmIP-RF [ThreadFunction():iseRTHss.cpp:163]
Apr 2 20:32:22 homematic-raspi user.err monit[1817]: 'sshdEnabled' status failed (1) -- no output
Apr 2 20:32:22 homematic-raspi user.err monit[1817]: 'hs485dEnabled' status failed (2) -- grep: /var/etc/hs485d.conf: No such file or directory
Apr 2 20:32:22 homematic-raspi user.err monit[1817]: 'multimacdEnabled' status failed (1) -- no output
Apr 2 20:32:22 homematic-raspi user.err monit[1817]: 'hmlangwEnabled' status failed (1) -- no output
Apr 2 20:32:22 homematic-raspi user.err monit[1817]: 'rfdEnabled' status failed (1) -- no output
Apr 2 20:32:22 homematic-raspi user.warn monit[1817]: 'HMIPServer' failed protocol test [DEFAULT] at [localhost]:39292 [TCP/IP] -- Connection refused
Apr 2 20:32:22 homematic-raspi user.warn monit[1817]: 'hasUSB' status failed (1) -- no output
Apr 2 20:32:22 homematic-raspi user.err monit[1817]: 'hb_rf_eth-CheckEnabled' status failed (1) -- no output
Apr 2 20:32:22 homematic-raspi user.err monit[1817]: 'coProcessorCheck' status failed (1) -- no output
Apr 2 20:32:22 homematic-raspi user.warn monit[1817]: 'eMMCLifeTimeCheck' status failed (1) -- no output
Apr 2 20:32:22 homematic-raspi user.err monit[1817]: 'tailscaleEnabled' status failed (1) -- no output
Apr 2 20:32:22 homematic-raspi user.err monit[1817]: Lookup for '/media/usb1' filesystem failed -- not found in /proc/self/mounts
Apr 2 20:32:22 homematic-raspi user.err monit[1817]: Filesystem '/media/usb1' not mounted
Apr 2 20:32:22 homematic-raspi user.err monit[1817]: 'usb1' unable to read filesystem '/media/usb1' state
Apr 2 20:32:22 homematic-raspi user.info monit[1817]: 'usb1' trying to restart
Apr 2 20:32:38 homematic-raspi user.warn monit[1817]: 'HMIPServer' failed protocol test [DEFAULT] at [localhost]:39292 [TCP/IP] -- Connection refused
Apr 2 20:32:40 homematic-raspi user.warn monit[1817]: 'hasUSB' status failed (1) -- no output
Apr 2 20:32:40 homematic-raspi user.err monit[1817]: 'wlan0CheckEnabled' status failed (1) -- no output
Apr 2 20:32:40 homematic-raspi user.warn monit[1817]: 'eMMCLifeTimeCheck' status failed (1) -- no output
Apr 2 20:32:40 homematic-raspi user.err monit[1817]: Filesystem '/media/usb1' not mounted
Apr 2 20:32:40 homematic-raspi user.err monit[1817]: 'usb1' unable to read filesystem '/media/usb1' state
Apr 2 20:32:40 homematic-raspi user.info monit[1817]: 'usb1' trying to restart
Apr 2 20:32:56 homematic-raspi user.warn monit[1817]: 'HMIPServer' failed protocol test [DEFAULT] at [localhost]:39292 [TCP/IP] -- Connection refused
Apr 2 20:32:57 homematic-raspi user.warn monit[1817]: 'hasUSB' status failed (1) -- no output
Apr 2 20:32:57 homematic-raspi user.err monit[1817]: 'eMMCLifeTimeCheck' status failed (1) -- no output
Apr 2 20:32:57 homematic-raspi user.err monit[1817]: Filesystem '/media/usb1' not mounted
Apr 2 20:32:57 homematic-raspi user.err monit[1817]: 'usb1' unable to read filesystem '/media/usb1' state
Apr 2 20:32:57 homematic-raspi user.info monit[1817]: 'usb1' trying to restart
Apr 2 20:33:08 homematic-raspi user.info firewall: configuration set
Apr 2 20:33:08 homematic-raspi user.info monit[1817]: 'sshd' restart on user request
Apr 2 20:33:08 homematic-raspi user.info monit[1817]: Monit daemon with PID 1817 awakened
Apr 2 20:33:08 homematic-raspi user.info monit[1817]: Awakened by User defined signal 1
Apr 2 20:33:08 homematic-raspi user.info monit[1817]: 'sshd' trying to restart
Apr 2 20:33:08 homematic-raspi user.info monit[1817]: 'sshd' restart: '/etc/init.d/S50sshd restart'
Apr 2 20:33:12 homematic-raspi auth.info sshd[2112]: Server listening on 0.0.0.0 port 22.
Apr 2 20:33:12 homematic-raspi auth.info sshd[2112]: Server listening on :: port 22.
Apr 2 20:33:13 homematic-raspi user.info monit[1817]: 'sshd' restart action done
Apr 2 20:33:16 homematic-raspi user.warn monit[1817]: 'HMIPServer' failed protocol test [DEFAULT] at [localhost]:39292 [TCP/IP] -- Connection refused
Apr 2 20:33:17 homematic-raspi user.warn monit[1817]: 'hasUSB' status failed (1) -- no output
Apr 2 20:33:17 homematic-raspi user.err monit[1817]: Filesystem '/media/usb1' not mounted
Apr 2 20:33:17 homematic-raspi user.err monit[1817]: 'usb1' unable to read filesystem '/media/usb1' state
Apr 2 20:33:17 homematic-raspi user.info monit[1817]: 'usb1' trying to restart
Apr 2 20:33:34 homematic-raspi user.err monit[1817]: 'HMIPServer' failed protocol test [DEFAULT] at [localhost]:39292 [TCP/IP] -- Connection refused
Apr 2 20:33:34 homematic-raspi user.info monit[1817]: 'HMIPServer' trying to restart
Apr 2 20:33:34 homematic-raspi user.info monit[1817]: 'HMIPServer' restart: '/etc/init.d/S62HMServer restart'
Apr 2 20:34:04 homematic-raspi user.err monit[1817]: 'HMIPServer' failed to restart (exit status -1) -- '/etc/init.d/S62HMServer restart': Program timed out -- Stopping HMIPServer: OK Starting HMIPServer: ...............
Apr 2 20:34:05 homematic-raspi user.err monit[1817]: 'hasUSB' status failed (1) -- no output
Apr 2 20:34:13 homematic-raspi auth.info sshd[2264]: Accepted password for root from 192.168.1.25 port 59920 ssh2
Apr 2 20:34:22 homematic-raspi user.err monit[1817]: 'HMIPServer' service restarted 1 times within 1 cycles(s) - exec
Apr 2 20:34:22 homematic-raspi user.info monit[1817]: 'HMIPServer' exec: '/bin/triggerAlarm.tcl HMIPServer restarted WatchDog: hmipserver-restart true'
Apr 2 20:34:22 homematic-raspi user.info monit[1817]: 'HMIPServer' process is running after previous exec error (slow starting or manually recovered?)
Apr 2 20:34:22 homematic-raspi user.info monit[1817]: 'HMIPServer' process is running after previous restart timeout (manually recovered?)
Apr 2 20:34:22 homematic-raspi user.err monit[1817]: 'HMIPServer' failed protocol test [DEFAULT] at [localhost]:39292 [TCP/IP] -- Connection refused
Apr 2 20:34:22 homematic-raspi user.info monit[1817]: 'HMIPServer' trying to restart
Apr 2 20:34:22 homematic-raspi user.info monit[1817]: 'HMIPServer' restart: '/etc/init.d/S62HMServer restart'
Apr 2 20:34:52 homematic-raspi user.err monit[1817]: 'HMIPServer' failed to restart (exit status -1) -- '/etc/init.d/S62HMServer restart': Program timed out -- Stopping HMIPServer: OK Starting HMIPServer: ...............
Apr 2 20:35:10 homematic-raspi user.info monit[1817]: 'HMIPServer' process is running after previous exec error (slow starting or manually recovered?)
Apr 2 20:35:10 homematic-raspi user.err monit[1817]: 'HMIPServer' failed protocol test [DEFAULT] at [localhost]:39292 [TCP/IP] -- Connection refused
Apr 2 20:35:10 homematic-raspi user.info monit[1817]: 'HMIPServer' trying to restart
Apr 2 20:35:10 homematic-raspi user.info monit[1817]: 'HMIPServer' restart: '/etc/init.d/S62HMServer restart'
Apr 2 20:35:40 homematic-raspi user.err monit[1817]: 'HMIPServer' failed to restart (exit status -1) -- '/etc/init.d/S62HMServer restart': Program timed out -- Stopping HMIPServer: OK Starting HMIPServer: ...............
Apr 2 20:35:58 homematic-raspi user.err monit[1817]: 'HMIPServer' service restarted 1 times within 1 cycles(s) - exec
Apr 2 20:35:58 homematic-raspi user.info monit[1817]: 'HMIPServer' exec: '/bin/triggerAlarm.tcl HMIPServer restarted WatchDog: hmipserver-restart true'
Apr 2 20:35:58 homematic-raspi user.info monit[1817]: 'HMIPServer' process is running after previous exec error (slow starting or manually recovered?)
Apr 2 20:35:58 homematic-raspi user.info monit[1817]: 'HMIPServer' process is running after previous restart timeout (manually recovered?)
Apr 2 20:35:58 homematic-raspi user.err monit[1817]: 'HMIPServer' failed protocol test [DEFAULT] at [localhost]:39292 [TCP/IP] -- Connection refused
Apr 2 20:35:58 homematic-raspi user.info monit[1817]: 'HMIPServer' trying to restart
Apr 2 20:35:58 homematic-raspi user.info monit[1817]: 'HMIPServer' restart: '/etc/init.d/S62HMServer restart'
dmesg
Code: Alles auswählen
root@homematic-raspi:/var/log# dmesg
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083]
[ 0.000000] Linux version 6.1.73 (builder@b152b859d874) (aarch64-buildroot-linux-gnu-gcc.br_real (Buildroot -g6d18e07) 12.3.0, GNU ld (GNU Binutils) 2.40) #1 SMP PREEMPT Sat Mar 16 12:41:06 UTC 2024
[ 0.000000] Kernel is locked down from Kernel configuration; see man kernel_lockdown.7
[ 0.000000] random: crng init done
[ 0.000000] Machine model: Raspberry Pi 4 Model B Rev 1.2
[ 0.000000] efi: UEFI not found.
[ 0.000000] Reserved memory: created CMA memory pool at 0x000000002ac00000, size 64 MiB
[ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000000000-0x000000003fffffff]
[ 0.000000] DMA32 [mem 0x0000000040000000-0x00000000fbffffff]
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000003dffffff]
[ 0.000000] node 0: [mem 0x0000000040000000-0x00000000fbffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000000fbffffff]
[ 0.000000] On node 0, zone DMA32: 8192 pages in unavailable ranges
[ 0.000000] On node 0, zone DMA32: 16384 pages in unavailable ranges
[ 0.000000] percpu: Embedded 28 pages/cpu s75176 r8192 d31320 u114688
[ 0.000000] pcpu-alloc: s75176 r8192 d31320 u114688 alloc=28*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Detected PIPT I-cache on CPU0
[ 0.000000] CPU features: detected: Spectre-v2
[ 0.000000] CPU features: detected: Spectre-v3a
[ 0.000000] CPU features: detected: Spectre-v4
[ 0.000000] CPU features: detected: Spectre-BHB
[ 0.000000] CPU features: kernel page table isolation forced ON by KASLR
[ 0.000000] CPU features: detected: Kernel page table isolation (KPTI)
[ 0.000000] CPU features: detected: ARM erratum 1742098
[ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[ 0.000000] alternatives: applying boot alternatives
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1007872
[ 0.000000] Kernel command line: dwc_otg.lpm_enable=0 sdhci_bcm2708.enable_llm=0 console=tty2 root=PARTUUID=deedbeef-02 ro rootfstype=ext4 fsck.repair=yes rootwait rootdelay=5 consoleblank=120 logo.nologo quiet loglevel=0 init_on_alloc=1 init_on_free=1 slab_nomerge iomem=relaxed net.ifnames=0 usb-storage.quirks=174c:55aa:u,2109:0715:u,152d:0578:u,152d:0579:u,152d:1561:u,174c:0829:u,14b0:0206:u,174c:225c:u,7825:a2a4:u,152d:0562:u coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_headphones=0 bcm2708_fb.fbwidth=640 bcm2708_fb.fbheight=480 bcm2708_fb.fbswap=1 smsc95xx.macaddr=DC:A6:32:71:F9:BC vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000 empty
[ 0.000000] Unknown kernel command line parameters "empty", will be passed to user space.
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 0.000000] mem auto-init: stack:all(zero), heap alloc:on, heap free:on
[ 0.000000] mem auto-init: clearing system memory may take some time...
[ 0.000000] software IO TLB: area num 4.
[ 0.000000] software IO TLB: mapped [mem 0x000000003a000000-0x000000003e000000] (64MB)
[ 0.000000] Memory: 3854788K/4096000K available (14848K kernel code, 2078K rwdata, 4112K rodata, 4288K init, 1353K bss, 175676K reserved, 65536K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] ftrace: allocating 40833 entries in 160 pages
[ 0.000000] ftrace: allocated 160 pages with 2 groups
[ 0.000000] Lockdown: swapper: use of tracefs is restricted; see man kernel_lockdown.7
[ 0.000000] Tracing disabled due to lockdown
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4.
[ 0.000000] Trampoline variant of Tasks RCU enabled.
[ 0.000000] Rude variant of Tasks RCU enabled.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 timer(s) running at 54.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xc743ce346, max_idle_ns: 440795203123 ns
[ 0.000000] sched_clock: 56 bits at 54MHz, resolution 18ns, wraps every 4398046511102ns
[ 0.000328] kfence: initialized - using 2097152 bytes for 255 objects at 0x(____ptrval____)-0x(____ptrval____)
[ 0.000479] Console: colour dummy device 80x25
[ 0.000537] printk: console [tty2] enabled
[ 0.000579] Calibrating delay loop (skipped), value calculated using timer frequency.. 108.00 BogoMIPS (lpj=216000)
[ 0.000598] pid_max: default: 32768 minimum: 301
[ 0.000742] LSM: Security Framework initializing
[ 0.000806] landlock: Up and running.
[ 0.000812] Yama: becoming mindful.
[ 0.000917] AppArmor: AppArmor initialized
[ 0.001063] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.001081] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.002068] cgroup: Disabling memory control group subsystem
[ 0.003619] cblist_init_generic: Setting adjustable number of callback queues.
[ 0.003632] cblist_init_generic: Setting shift to 2 and lim to 1.
[ 0.003746] cblist_init_generic: Setting adjustable number of callback queues.
[ 0.003755] cblist_init_generic: Setting shift to 2 and lim to 1.
[ 0.003911] cblist_init_generic: Setting adjustable number of callback queues.
[ 0.003920] cblist_init_generic: Setting shift to 2 and lim to 1.
[ 0.004171] rcu: Hierarchical SRCU implementation.
[ 0.004180] rcu: Max phase no-delay instances is 1000.
[ 0.005944] EFI services will not be available.
[ 0.006290] smp: Bringing up secondary CPUs ...
[ 0.006903] Detected PIPT I-cache on CPU1
[ 0.007058] CPU1: Booted secondary processor 0x0000000001 [0x410fd083]
[ 0.007754] Detected PIPT I-cache on CPU2
[ 0.007881] CPU2: Booted secondary processor 0x0000000002 [0x410fd083]
[ 0.008574] Detected PIPT I-cache on CPU3
[ 0.008703] CPU3: Booted secondary processor 0x0000000003 [0x410fd083]
[ 0.008803] smp: Brought up 1 node, 4 CPUs
[ 0.008821] SMP: Total of 4 processors activated.
[ 0.008830] CPU features: detected: 32-bit EL0 Support
[ 0.008838] CPU features: detected: CRC32 instructions
[ 0.008937] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[ 0.008948] CPU: All CPU(s) started at EL2
[ 0.008953] alternatives: applying system-wide alternatives
[ 0.010898] devtmpfs: initialized
[ 0.021988] Enabled cp15_barrier support
[ 0.022019] Enabled setend support
[ 0.022168] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.022196] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.022300] Lockdown: swapper/0: use of tracefs is restricted; see man kernel_lockdown.7
[ 0.022308] Can not register tracer wakeup due to lockdown
[ 0.022320] Lockdown: swapper/0: use of tracefs is restricted; see man kernel_lockdown.7
[ 0.022327] Can not register tracer function_graph due to lockdown
[ 0.054132] pinctrl core: initialized pinctrl subsystem
[ 0.054818] DMI not present or invalid.
[ 0.055322] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.059057] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations
[ 0.059360] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.060366] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.060478] audit: initializing netlink subsys (disabled)
[ 0.060720] audit: type=2000 audit(0.060:1): state=initialized audit_enabled=0 res=1
[ 0.061257] thermal_sys: Registered thermal governor 'step_wise'
[ 0.061320] cpuidle: using governor menu
[ 0.061962] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.062097] ASID allocator initialised with 32768 entries
[ 0.069534] bcm2835-mbox fe00b880.mailbox: mailbox enabled
[ 0.080200] raspberrypi-firmware soc:firmware: Attached to firmware from 2023-10-17T15:39:16, variant start
[ 0.084212] raspberrypi-firmware soc:firmware: Firmware hash is 30f0c5e4d076da3ab4f341d88e7d505760b93ad7
[ 0.094077] KASLR enabled
[ 0.119454] bcm2835-dma fe007000.dma: DMA legacy API manager, dmachans=0x1
[ 0.122410] iommu: Default domain type: Translated
[ 0.122424] iommu: DMA domain TLB invalidation policy: strict mode
[ 0.122815] SCSI subsystem initialized
[ 0.123000] usbcore: registered new interface driver usbfs
[ 0.123050] usbcore: registered new interface driver hub
[ 0.123091] usbcore: registered new device driver usb
[ 0.123252] usb_phy_generic phy: supply vcc not found, using dummy regulator
[ 0.123594] pps_core: LinuxPPS API ver. 1 registered
[ 0.123603] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.123623] PTP clock support registered
[ 0.124681] vgaarb: loaded
[ 0.125539] clocksource: Switched to clocksource arch_sys_counter
[ 0.125555] Lockdown: swapper/0: use of tracefs is restricted; see man kernel_lockdown.7
[ 0.125563] Tracing disabled due to lockdown
[ 0.125570] Lockdown: swapper/0: use of tracefs is restricted; see man kernel_lockdown.7
[ 0.125577] Tracing disabled due to lockdown
[ 0.125588] Lockdown: swapper/0: use of tracefs is restricted; see man kernel_lockdown.7
[ 0.125594] Tracing disabled due to lockdown
[ 0.125603] Lockdown: swapper/0: use of tracefs is restricted; see man kernel_lockdown.7
[ 0.125610] Tracing disabled due to lockdown
[ 0.125616] Lockdown: swapper/0: use of tracefs is restricted; see man kernel_lockdown.7
[ 0.125622] Tracing disabled due to lockdown
[ 0.125976] VFS: Disk quotas dquot_6.6.0
[ 0.126032] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.126131] FS-Cache: Loaded
[ 0.126282] CacheFiles: Loaded
[ 0.126791] AppArmor: AppArmor Filesystem Enabled
[ 0.136046] NET: Registered PF_INET protocol family
[ 0.136194] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.141084] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
[ 0.141140] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.141181] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 0.141372] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear)
[ 0.142378] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.142700] MPTCP token hash table entries: 4096 (order: 4, 98304 bytes, linear)
[ 0.142886] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 0.142938] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 0.143182] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.143869] RPC: Registered named UNIX socket transport module.
[ 0.143882] RPC: Registered udp transport module.
[ 0.143888] RPC: Registered tcp transport module.
[ 0.143893] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.143908] PCI: CLS 0 bytes, default 64
[ 0.146175] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
[ 0.147218] Lockdown: swapper/0: use of tracefs is restricted; see man kernel_lockdown.7
[ 0.147231] Tracing disabled due to lockdown
[ 0.147240] Lockdown: swapper/0: use of tracefs is restricted; see man kernel_lockdown.7
[ 0.147247] Can not register tracer blk due to lockdown
[ 0.147253] blktrace: Warning: could not register the block tracer
[ 0.147578] Initialise system trusted keyrings
[ 0.147816] workingset: timestamp_bits=46 max_order=20 bucket_order=0
[ 0.159407] NFS: Registering the id_resolver key type
[ 0.159461] Key type id_resolver registered
[ 0.159469] Key type id_legacy registered
[ 0.159572] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.159594] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 0.159632] ntfs: driver 2.1.32 [Flags: R/W].
[ 0.161862] Key type asymmetric registered
[ 0.161876] Asymmetric key parser 'x509' registered
[ 0.161952] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 0.162194] io scheduler mq-deadline registered
[ 0.162205] io scheduler kyber registered
[ 0.167766] brcm-pcie fd500000.pcie: host bridge /scb/pcie@7d500000 ranges:
[ 0.167800] brcm-pcie fd500000.pcie: No bus range found for /scb/pcie@7d500000, using [bus 00-ff]
[ 0.167840] brcm-pcie fd500000.pcie: MEM 0x0600000000..0x063fffffff -> 0x00c0000000
[ 0.167877] brcm-pcie fd500000.pcie: IB MEM 0x0000000000..0x00bfffffff -> 0x0400000000
[ 0.168389] brcm-pcie fd500000.pcie: setting SCB_ACCESS_EN, READ_UR_MODE, MAX_BURST_SIZE
[ 0.168710] brcm-pcie fd500000.pcie: PCI host bridge to bus 0000:00
[ 0.168727] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.168742] pci_bus 0000:00: root bus resource [mem 0x600000000-0x63fffffff] (bus address [0xc0000000-0xffffffff])
[ 0.168785] pci 0000:00:00.0: [14e4:2711] type 01 class 0x060400
[ 0.168873] pci 0000:00:00.0: PME# supported from D0 D3hot
[ 0.172816] pci_bus 0000:01: supply vpcie3v3 not found, using dummy regulator
[ 0.172956] pci_bus 0000:01: supply vpcie3v3aux not found, using dummy regulator
[ 0.173015] pci_bus 0000:01: supply vpcie12v not found, using dummy regulator
[ 0.279627] brcm-pcie fd500000.pcie: link up, 5.0 GT/s PCIe x1 (SSC)
[ 0.279809] pci 0000:01:00.0: [1106:3483] type 00 class 0x0c0330
[ 0.279902] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00000fff 64bit]
[ 0.280184] pci 0000:01:00.0: PME# supported from D0 D3cold
[ 0.289647] pci 0000:00:00.0: BAR 8: assigned [mem 0x600000000-0x6000fffff]
[ 0.289671] pci 0000:01:00.0: BAR 0: assigned [mem 0x600000000-0x600000fff 64bit]
[ 0.289732] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.289744] pci 0000:00:00.0: bridge window [mem 0x600000000-0x6000fffff]
[ 0.289967] pcieport 0000:00:00.0: enabling device (0000 -> 0002)
[ 0.290112] pcieport 0000:00:00.0: PME: Signaling with IRQ 30
[ 0.290422] pcieport 0000:00:00.0: AER: enabled with IRQ 30
[ 0.291173] simple-framebuffer 3ea9b000.framebuffer: framebuffer at 0x3ea9b000, 0x12c000 bytes
[ 0.291189] simple-framebuffer 3ea9b000.framebuffer: format=a8r8g8b8, mode=640x480x32, linelength=2560
[ 0.291618] Console: switching to colour frame buffer device 80x30
[ 0.292902] simple-framebuffer 3ea9b000.framebuffer: fb0: simplefb registered!
[ 0.297312] Serial: 8250/16550 driver, 1 ports, IRQ sharing enabled
[ 0.299071] iproc-rng200 fe104000.rng: hwrng registered
[ 0.299307] vc-mem: phys_addr:0x00000000 mem_base=0x3ec00000 mem_size:0x40000000(1024 MiB)
[ 0.310041] brd: module loaded
[ 0.316234] loop: module loaded
[ 0.316736] zram: Added device: zram0
[ 0.317310] Loading iSCSI transport class v2.0-870.
[ 0.320628] tun: Universal TUN/TAP device driver, 1.6
[ 0.321595] bcmgenet fd580000.ethernet: GENET 5.0 EPHY: 0x0000
[ 0.421665] unimac-mdio unimac-mdio.-19: Broadcom UniMAC MDIO bus
[ 0.423870] xhci_hcd 0000:01:00.0: enabling device (0000 -> 0002)
[ 0.423945] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 0.423974] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 1
[ 0.424537] xhci_hcd 0000:01:00.0: hcc params 0x002841eb hci version 0x100 quirks 0x0b00040000000890
[ 0.425016] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 0.425036] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[ 0.425053] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed
[ 0.425304] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[ 0.425322] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.425333] usb usb1: Product: xHCI Host Controller
[ 0.425343] usb usb1: Manufacturer: Linux 6.1.73 xhci-hcd
[ 0.425352] usb usb1: SerialNumber: 0000:01:00.0
[ 0.425913] hub 1-0:1.0: USB hub found
[ 0.425988] hub 1-0:1.0: 1 port detected
[ 0.426669] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01
[ 0.426686] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.426697] usb usb2: Product: xHCI Host Controller
[ 0.426706] usb usb2: Manufacturer: Linux 6.1.73 xhci-hcd
[ 0.426715] usb usb2: SerialNumber: 0000:01:00.0
[ 0.427200] hub 2-0:1.0: USB hub found
[ 0.427270] hub 2-0:1.0: 4 ports detected
[ 0.428315] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[ 0.428418] dwc_otg: FIQ enabled
[ 0.428425] dwc_otg: NAK holdoff enabled
[ 0.428431] dwc_otg: FIQ split-transaction FSM enabled
[ 0.428445] Module dwc_common_port init
[ 0.429098] usbcore: registered new interface driver uas
[ 0.429174] usbcore: registered new interface driver usb-storage
[ 0.429267] usbcore: registered new interface driver usbserial_generic
[ 0.429295] usbserial: USB Serial support registered for generic
[ 0.429731] Driver for 1-wire Dallas network protocol.
[ 0.431061] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com
[ 0.433282] sdhci: Secure Digital Host Controller Interface driver
[ 0.433296] sdhci: Copyright(c) Pierre Ossman
[ 0.433500] Error: Driver 'sdhost-bcm2835' is already registered, aborting...
[ 0.433510] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.436826] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.436929] hid: raw HID events driver (C) Jiri Kosina
[ 0.437070] usbcore: registered new interface driver usbhid
[ 0.437074] usbhid: USB HID core driver
[ 0.442737] NET: Registered PF_INET6 protocol family
[ 0.443566] Segment Routing with IPv6
[ 0.443586] In-situ OAM (IOAM) with IPv6
[ 0.443671] NET: Registered PF_PACKET protocol family
[ 0.443714] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 0.443763] Key type dns_resolver registered
[ 0.444458] registered taskstats version 1
[ 0.444493] Loading compiled-in X.509 certificates
[ 0.446715] Loaded X.509 cert 'Build time autogenerated kernel key: c62db4b3a5b1783de6b17d82c07d95988e324b19'
[ 0.446939] Key type .fscrypt registered
[ 0.446945] Key type fscrypt-provisioning registered
[ 0.447072] AppArmor: AppArmor sha1 policy hashing enabled
[ 0.458106] fe215040.serial: ttyS0 at MMIO 0xfe215040 (irq = 35, base_baud = 62500000) is a 16550
[ 0.458669] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer
[ 0.458795] bcm2835-power bcm2835-power: Broadcom BCM2835 power domains driver
[ 0.459194] mmc-bcm2835 fe300000.mmcnr: mmc_debug:0 mmc_debug2:0
[ 0.459202] mmc-bcm2835 fe300000.mmcnr: DMA channel allocated
[ 0.486581] of_cfs_init
[ 0.486727] of_cfs_init: OK
[ 0.487834] Waiting 5 sec before mounting root device...
[ 0.521617] mmc0: SDHCI controller on fe340000.mmc [fe340000.mmc] using ADMA
[ 0.566197] mmc1: new high speed SDIO card at address 0001
[ 0.621742] mmc0: new ultra high speed DDR50 SDHC card at address aaaa
[ 0.622182] mmcblk0: mmc0:aaaa SH32G 29.7 GiB
[ 0.623811] mmcblk0: p1 p2 p3
[ 0.624147] mmcblk0: mmc0:aaaa SH32G 29.7 GiB (quirks 0x00004000)
[ 0.681557] usb 1-1: new high-speed USB device number 2 using xhci_hcd
[ 0.832204] usb 1-1: New USB device found, idVendor=2109, idProduct=3431, bcdDevice= 4.21
[ 0.832224] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 0.832236] usb 1-1: Product: USB2.0 Hub
[ 0.833652] hub 1-1:1.0: USB hub found
[ 0.833941] hub 1-1:1.0: 4 ports detected
[ 1.129576] usb 1-1.3: new full-speed USB device number 3 using xhci_hcd
[ 1.238621] usb 1-1.3: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[ 1.238640] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1.238651] usb 1-1.3: Product: ConBee II
[ 1.238660] usb 1-1.3: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 1.238670] usb 1-1.3: SerialNumber: DE2193845
[ 5.630919] EXT4-fs (mmcblk0p2): orphan cleanup on readonly fs
[ 5.631278] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Quota mode: none.
[ 5.631353] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 5.631875] devtmpfs: mounted
[ 5.639667] Freeing unused kernel memory: 4288K
[ 5.678784] Checked W+X mappings: passed, no W+X pages found
[ 5.678817] Run /sbin/init as init process
[ 5.678821] with arguments:
[ 5.678823] /sbin/init
[ 5.678825] empty
[ 5.678828] with environment:
[ 5.678830] HOME=/
[ 5.678832] TERM=linux
[ 6.045436] EXT4-fs: Mount option(s) incompatible with ext2
[ 6.262904] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Quota mode: none.
[ 7.320159] zram: Added device: zram1
[ 7.322897] zram1: detected capacity change from 0 to 8241688
[ 7.348676] Adding 4120840k swap on /dev/zram1. Priority:75 extents:1 across:4120840k SS
[ 7.403576] i2c_dev: i2c /dev entries driver
[ 9.603180] udevd[1041]: starting version 3.2.14
[ 9.634755] udevd[1042]: starting eudev-3.2.14
[ 9.800669] rpi-gpiomem fe200000.gpiomem: window base 0xfe200000 size 0x00001000
[ 9.800820] rpi-gpiomem fe200000.gpiomem: initialised 1 regions as /dev/gpiomem
[ 9.806866] generic_raw_uart: loading out-of-tree module taints kernel.
[ 9.813357] vc_sm_cma: module is from the staging directory, the quality is unknown, you have been warned.
[ 9.814966] bcm2835_vc_sm_cma_probe: Videocore shared memory driver
[ 9.814989] [vc_sm_connected_init]: start
[ 9.815744] [vc_sm_connected_init]: installed successfully
[ 9.834185] pl011_raw_uart fe201000.serial: there is not valid maps for state default
[ 9.834374] pl011_raw_uart fe201000.serial: Initialized pl011 device; mapbase=0xfe201000; irq=39; clockrate=48000001
[ 9.834437] pl011_raw_uart fe201000.serial: Missing I2C driver of rtc device, trying to load
[ 9.834442] pl011_raw_uart fe201000.serial: Requesting module i2c:rx8130
[ 9.843380] rtc-ds1307: probe of 1-0032 failed with error -5
[ 9.846550] rtc-ds1307: probe of 1-0032 failed with error -5
[ 9.846903] raw-uart raw-uart: Reset radio module
[ 9.897484] cdc_acm 1-1.3:1.0: ttyACM0: USB ACM device
[ 9.897609] usbcore: registered new interface driver cdc_acm
[ 9.897616] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 9.960310] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 9.968573] cfg80211: Loaded X.509 cert 'benh@debian.org: 577e021cb980e0e820821ba7b54b4961b8b4fadf'
[ 9.968994] cfg80211: Loaded X.509 cert 'romain.perier@gmail.com: 3abbc6ec146e09d1b6016ab9d6cf71dd233f0328'
[ 9.969389] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 9.969840] cfg80211: Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600'
[ 10.012433] brcmfmac: F1 signature read @0x18000000=0x15264345
[ 10.016083] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 10.016486] usbcore: registered new interface driver brcmfmac
[ 10.029550] raw-uart raw-uart: Registered new raw-uart device using underlying device GPIO@fe201000.serial.
[ 10.236498] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Nov 1 2021 00:37:25 version 7.45.241 (1a2f2fa CY) FWID 01-703fd60
[ 10.297300] bcmgenet fd580000.ethernet: configuring instance for external RGMII (RX delay)
[ 10.298127] bcmgenet fd580000.ethernet eth0: Link is Down
[ 14.397791] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 14.398269] bcmgenet fd580000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 27.992308] raw-uart raw-uart: Reset radio module
[ 30.210842] raw-uart raw-uart: Reset radio module
[ 34.277203] raw-uart raw-uart: Reset radio module
Da ist auf jeden Fall schon einiges Interessantes drin. Ich werde auch gleich selbst mal durchgehen.
Braucht ihr noch mehr?