pivccu BidCos RF Fehler

[Bruce001]

Hallo Leute,

wende mich nun an Euch, da ich mit meinem wenigen Latein am Ende bin.

Will eigentlich ein System mit Homematic Steuerung und ioBroker in einem.

Raspi3 und Funkmodul sind istalliert und liefen unter rasparrymativ einwandfrei.

Nun habe ich mir ein Image installiert, dass ioBroker und pivccu vereint (keine Frickelei mit YAHM )

Problem ist, dass ich unter pivccu oder unter YAHM einen Fehler mit dem BidCos Modul habe.

Nun habe ich zwischenzeitlich festgestellt, dass die Firmware des Funkmoduls Schuld sein kann. Also alte Version geflasht, was auch funktiuoniert hat, aber Fehler identisch. KAnn keine meiner Homematic-Thermostate ansteuern und erhalte einen Bidcos Fehler.

sudo pivccu-info


piVCCU version: 2.31.25-25
Kernel modules: Available
Raw UART dev: Available
Rasp.Pi3 UART: Assigned to GPIO pins
Board serial: OEQ0310155
State: RUNNING
PID: 653
IP: 192.168.0.17
IP: 2a02:908:2053:9080:98c6:70ff:fe7e:628d
CPU use: 40.57 seconds
BlkIO use: 43.09 MiB
Link: vethpivccu
TX bytes: 1.72 MiB
RX bytes: 2.27 MiB
Total bytes: 3.99 MiB

sudo pivccu-attach cat /var/log/messages

Code: Alles auswählen

Oct 16 16:17:39 homematic-ccu2 syslog.info syslogd started: BusyBox v1.20.2
Oct 16 16:17:39 homematic-ccu2 user.notice kernel: klogd started: BusyBox v1.20.                                 2 (2018-01-15 15:55:20 CET)
Oct 16 14:17:40 homematic-ccu2 daemon.info ifplugd(eth0)[139]: ifplugd 0.28 init                                 ializing.
Oct 16 14:17:40 homematic-ccu2 daemon.info ifplugd(eth0)[139]: Using interface e                                 th0/9A:C6:70:7E:62:8D with driver <veth> (version: 1.0)
Oct 16 14:17:40 homematic-ccu2 daemon.info ifplugd(eth0)[139]: Using detection m                                 ode: SIOCETHTOOL
Oct 16 14:17:40 homematic-ccu2 daemon.info ifplugd(eth0)[139]: Initialization co                                 mplete, link beat detected.
Oct 16 14:17:40 homematic-ccu2 daemon.warn ifplugd(eth0)[139]: Could not open /d                                 ev/tty, cannot beep.
Oct 16 14:17:40 homematic-ccu2 daemon.info ifplugd(eth0)[139]: Executing '/etc/i                                 fplugd/ifplugd.action eth0 up'.
Oct 16 14:17:40 homematic-ccu2 daemon.warn ifplugd(eth0)[139]: client: net.ipv4.                                 tcp_timestamps = 0
Oct 16 14:17:40 homematic-ccu2 daemon.warn ifplugd(eth0)[139]: client: udhcpc (v                                 1.20.2) started
Oct 16 16:17:40 homematic-ccu2 user.debug setclock: Try to get time from 0.de.po                                 ol.ntp.org
Oct 16 14:17:40 homematic-ccu2 daemon.warn ifplugd(eth0)[139]: client: Sending d                                 iscover...
Oct 16 16:17:40 homematic-ccu2 user.debug setclock: Try to get time from 1.de.po                                 ol.ntp.org
Oct 16 16:17:40 homematic-ccu2 user.debug setclock: Try to get time from 2.de.po                                 ol.ntp.org
Oct 16 16:17:40 homematic-ccu2 user.debug setclock: Try to get time from 3.de.po                                 ol.ntp.org
Oct 16 16:17:40 homematic-ccu2 user.debug setclock: Tue Oct 16 16:17:40 CEST 201                                 8
Oct 16 14:17:40 homematic-ccu2 daemon.warn ifplugd(eth0)[139]: client: Sending s                                 elect for 192.168.0.17...
Oct 16 14:17:40 homematic-ccu2 daemon.warn ifplugd(eth0)[139]: client: Lease of                                  192.168.0.17 obtained, lease time 3600
Oct 16 14:17:40 homematic-ccu2 daemon.warn ifplugd(eth0)[139]: client: rm: can't                                  remove '/var/etc/resolv.conf': No such file or directory
Oct 16 14:17:41 homematic-ccu2 daemon.warn ifplugd(eth0)[139]: client: udhcpc (v                                 1.20.2) started
Oct 16 14:17:41 homematic-ccu2 daemon.warn ifplugd(eth0)[139]: client: Sending d                                 iscover...
Oct 16 14:17:41 homematic-ccu2 daemon.warn ifplugd(eth0)[139]: client: Sending s                                 elect for 192.168.0.17...
Oct 16 14:17:41 homematic-ccu2 daemon.warn ifplugd(eth0)[139]: client: Lease of                                  192.168.0.17 obtained, lease time 3600
Oct 16 14:17:42 homematic-ccu2 daemon.info ifplugd(eth0)[139]: Program executed                                  successfully.
Oct 16 14:17:45 homematic-ccu2 auth.info sshd[260]: Server listening on 0.0.0.0                                  port 22.
Oct 16 14:17:45 homematic-ccu2 auth.info sshd[260]: Server listening on :: port                                  22.
Oct 16 14:17:45 homematic-ccu2 user.info logger: Updating RF Lan Gateway Coproce                                 ssor Firmware
Oct 16 14:17:45 homematic-ccu2 user.debug update-coprocessor: firmware filename                                  is: coprocessor_update_hm_only.eq3
Oct 16 14:17:45 homematic-ccu2 user.info logger: Updating RF Lan Gateway Firmwar                                 e
Oct 16 14:17:45 homematic-ccu2 user.info update-lgw-firmware: No gateway found i                                 n config file /etc/config/rfd.conf
Oct 16 14:17:45 homematic-ccu2 user.info logger: Updating Wired Lan Gateway Firm                                 ware
Oct 16 14:17:45 homematic-ccu2 user.info update-lgw-firmware: No gateway found i                                 n config file /etc/config/hs485d.conf
Oct 16 16:17:50 homematic-ccu2 user.info update-coprocessor: Version: 2.8.6
Oct 16 16:17:50 homematic-ccu2 user.info update-coprocessor: No update necessary
Oct 16 16:17:51 homematic-ccu2 user.debug multimac: FastMacResponder::ThreadFunc                                 tion() started Id=297
Oct 16 16:17:51 homematic-ccu2 user.debug multimac: MacController::ThreadFunctio                                 n() started. Id=298
Oct 16 16:17:51 homematic-ccu2 user.debug multimac: C<: #0 COMMON IdentifyReques                                 t
Oct 16 16:17:51 homematic-ccu2 user.debug multimac: SubsystemManager::ThreadFunc                                 tion() started. Id=299
Oct 16 16:17:51 homematic-ccu2 user.debug multimac: C< @31802: bin:FD 00 03 FE 0                                 0 01 14 1E
Oct 16 16:17:51 homematic-ccu2 user.debug multimac: UpstreamCharConnection slave                                  ttyS0 ThreadFunction() started Id=300
Oct 16 16:17:51 homematic-ccu2 user.debug multimac: Subsystem 1 ThreadFunction()                                  started. Id=301
Oct 16 16:17:51 homematic-ccu2 user.debug multimac: UpstreamCharConnection slave                                  mmd_bidcos ThreadFunction() started Id=302
Oct 16 16:17:51 homematic-ccu2 user.debug multimac: Subsystem 2 ThreadFunction()                                  started. Id=303
Oct 16 16:17:51 homematic-ccu2 user.info kernel: [   31.804472] eq3loop: created                                  slave ttyS0
Oct 16 16:17:51 homematic-ccu2 user.info kernel: [   31.805029] eq3loop: created                                  slave mmd_bidcos
Oct 16 16:17:52 homematic-ccu2 user.debug multimac: C<: #1 HmSystem Identify
Oct 16 16:17:52 homematic-ccu2 user.debug multimac: C< @32802: bin:FD 00 03 00 0                                 1 00 9E 03
Oct 16 16:17:52 homematic-ccu2 user.debug multimac: C> @32805: #1 BOOTLOADER CMD                                 =04  02 43 6F 5F 43 50 55 5F 42 4C
Oct 16 16:17:52 homematic-ccu2 user.info multimac: Legacy Bootloader detected. S                                 tarting application.
Oct 16 16:17:52 homematic-ccu2 user.debug multimac: C<: #2 HmSystem StartBootloa                                 der
Oct 16 16:17:52 homematic-ccu2 user.debug multimac: C< @32805: bin:FD 00 03 00 0                                 2 03 94 09
Oct 16 16:17:53 homematic-ccu2 user.debug multimac: C> @33335: #2 BOOTLOADER CMD                                 =04  01
Oct 16 16:17:53 homematic-ccu2 user.debug multimac: C> @33374: #1 COMMON Identif                                 y DualCoPro_App
Oct 16 16:17:53 homematic-ccu2 user.info multimac: Copro application running.
Oct 16 16:17:53 homematic-ccu2 user.debug multimac: C<: #3 TRX GetVersion
Oct 16 16:17:53 homematic-ccu2 user.debug multimac: C< @33374: bin:FD 00 03 01 0                                 3 02 12 18
Oct 16 16:17:53 homematic-ccu2 user.debug multimac: C> @33477: #3 TRX Response A                                 ck 02 08 06 01 00 03 01 14 03
Oct 16 16:17:53 homematic-ccu2 user.info multimac: Vapp=020806 Vbl=010003 Vhmos=                                 011403
Oct 16 16:17:53 homematic-ccu2 user.debug multimac: C<: #4 COMMON GetSGTIN
Oct 16 16:17:53 homematic-ccu2 user.debug multimac: C< @33477: bin:FD 00 03 FE 0                                 4 04 8C 03
Oct 16 16:17:53 homematic-ccu2 user.debug multimac: C> @33581: #4 COMMON Respons                                 e Ack 30 14 F7 11 A0 61 A7 D7 09 8E 23 8B
Oct 16 16:17:53 homematic-ccu2 user.info multimac: SGTIN=30 14 F7 11 A0 61 A7 D7                                  09 8E 23 8B
Oct 16 16:17:53 homematic-ccu2 user.debug multimac: C<: #5 LLMAC GetDefaultRfAdd                                 ress
Oct 16 16:17:53 homematic-ccu2 user.debug multimac: C< @33581: bin:FD 00 03 03 0                                 5 08 86 0F
Oct 16 16:17:53 homematic-ccu2 user.debug multimac: C> @33584: #5 LLMAC Response                                  ACK @22602: 58 4A 44
Oct 16 16:17:53 homematic-ccu2 user.info multimac: RF address=5786180
Oct 16 16:17:53 homematic-ccu2 user.debug multimac: C<: #6 LLMAC GetSerialNumber
Oct 16 16:17:53 homematic-ccu2 user.debug multimac: C< @33584: bin:FD 00 03 03 0                                 6 07 8C 2D
Oct 16 16:17:53 homematic-ccu2 user.debug multimac: C> @33589: #6 LLMAC Response                                  ACK @20293: 4F 45 51 30 33 31 30 31 35 35
Oct 16 16:17:53 homematic-ccu2 user.info multimac: Serial Number=OEQ0310155
Oct 16 16:17:53 homematic-ccu2 user.debug multimac: C<: #7 LLMAC GetTimestamp
Oct 16 16:17:53 homematic-ccu2 user.debug multimac: C< @33589: bin:FD 00 03 03 0                                 7 02 0A 30
Oct 16 16:17:53 homematic-ccu2 user.debug multimac: C> @33592: #7 LLMAC Response                                  ACK @231: 00 E7
Oct 16 16:17:53 homematic-ccu2 user.info multimac: Timer=  231
Oct 16 16:18:06 homematic-ccu2 user.info rfd: BidCoS-Service started
Oct 16 16:18:06 homematic-ccu2 user.info rfd: XmlRpc Server is listening on TCP                                  port 2001
Oct 16 16:18:06 homematic-ccu2 user.warn rfd: opendir(/etc/config/firmware//) fa                                 iled
Oct 16 16:18:06 homematic-ccu2 user.err rfd: No BidCoS-Interface available
Oct 16 16:18:06 homematic-ccu2 user.warn rfd: Error initializing interfaces
Oct 16 16:18:14 homematic-ccu2 user.debug multimac: C<: #8 TRX GetDutyCycle
Oct 16 16:18:14 homematic-ccu2 user.debug multimac: C< @43592: bin:FD 00 03 01 0                                 8 03 28 1E
Oct 16 16:18:14 homematic-ccu2 user.debug multimac: C> @43694: #8 TRX Response A                                 ck 00
Oct 16 16:18:14 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:18:16 homematic-ccu2 user.debug multimac: UpstreamCharConnection slave                                  device ttyS0 opened
Oct 16 16:18:16 homematic-ccu2 user.debug multimac: UpstreamCharConnection slave                                  device ttyS0 closed
Oct 16 16:18:16 homematic-ccu2 user.debug multimac: UpstreamCharConnection slave                                  device ttyS0 opened
Oct 16 16:18:16 homematic-ccu2 user.debug multimac: UpstreamCharConnection slave                                  device ttyS0 closed
Oct 16 16:18:16 homematic-ccu2 user.debug multimac: UpstreamCharConnection slave                                  device ttyS0 opened
Oct 16 16:18:16 homematic-ccu2 user.debug multimac: A>: #235 COMMON GetSGTIN
Oct 16 16:18:16 homematic-ccu2 user.debug multimac: A<: #235 COMMON Response Ack                                  30 14 F7 11 A0 61 A7 D7 09 8E 23 8B
Oct 16 16:18:16 homematic-ccu2 user.debug multimac: A>: #236 COMMON IdentifyRequ                                 est
Oct 16 16:18:16 homematic-ccu2 user.debug multimac: A<: #236 COMMON Response Ack                                  48 4D 49 50 5F 54 52 58 5F 41 70 70
Oct 16 16:18:16 homematic-ccu2 user.debug multimac: A>: #24 HMIP CMD=00  BC 86 4                                 B
Oct 16 16:18:16 homematic-ccu2 user.debug multimac: MacController::OnDownstreamF                                 rame(#24 HMIP CMD=00  BC 86 4B)
Oct 16 16:18:16 homematic-ccu2 user.debug multimac: C<: #9 HMIP CMD=00  BC 86 4B
Oct 16 16:18:16 homematic-ccu2 user.debug multimac: C< @46000: bin:FD 00 06 02 0                                 9 00 BC 86 4B 6B 8B
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: C> @46102: #9 HMIP CMD=06  0                                 1
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: A<: #24 HMIP CMD=06  01
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: A>: #25 HMIP CMD=0D  03
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: MacController::OnDownstreamF                                 rame(#25 HMIP CMD=0D  03)
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: C<: #10 HMIP CMD=0D  03
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: C< @46107: bin:FD 00 04 02 0                                 A 0D 03 87 B9
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: C> @46110: #10 HMIP CMD=06                                   01
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: A<: #25 HMIP CMD=06  01
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: A>: #172 TRX GetVersion
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: A<: #172 TRX Response Ack 02                                  08 06 01 00 03 01 14 03
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: A>: #173 TRX CMD=09
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: MacController::OnDownstreamF                                 rame(#173 TRX CMD=09  )
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: C<: #11 TRX CMD=09
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: C< @46151: bin:FD 00 03 01 0                                 B 09 22 22
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: C> @46252: #11 TRX Response                                  Ack 03
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: A<: #173 TRX Response Ack 03
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: A>: #174 TRX GetDutyCycle
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: A<: #174 TRX Response Ack 00
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: A>: #175 TRX CMD=07  C8
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: MacController::OnDownstreamF                                 rame(#175 TRX CMD=07  C8)
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: C<: #12 TRX CMD=07  C8
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: C< @46278: bin:FD 00 04 01 0                                 C 07 C8 05 78
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: C> @46380: #12 TRX Response                                  Ack
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: A<: #175 TRX Response Ack
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: A>: #26 HMIP CMD=0A
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: MacController::OnDownstreamF                                 rame(#26 HMIP CMD=0A  )
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: C<: #13 HMIP CMD=0A
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: C< @46382: bin:FD 00 03 02 0                                 D 0A 36 14
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: C> @46386: #13 HMIP CMD=06                                   01 31 DF A6 00
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: A<: #26 HMIP CMD=06  01 31 D                                 F A6 00
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: A>: #27 HMIP CMD=08  31 DF A                                 9 92
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: MacController::OnDownstreamF                                 rame(#27 HMIP CMD=08  31 DF A9 92)
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: C<: #14 HMIP CMD=08  31 DF A                                 9 92
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: C< @46405: bin:FD 00 07 02 0                                 E 08 31 DF A9 92 5E 12
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: C> @46412: #14 HMIP CMD=06                                   01
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: A<: #27 HMIP CMD=06  01
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: A>: #28 HMIP CMD=14  0F 1B 5                                 5 01 62 98 33 E0 BA B6 98 0D EC E2 F2 AA 64 8F 0C 18 93 5F 42 B5 90 E1 2E D7 E5                                  84 63 3A 4A FE F1 4D 65 38 92 E5 CC 49 96 4A 39 B5 CD 75 4B C7 52 50 79 96 23 50                                  04 1E E5 C9 32 68 E8 91 9B 9D
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: MacController::OnDownstreamF                                 rame(#28 HMIP CMD=14  0F 1B 55 01 62 98 33 E0 BA B6 98 0D EC E2 F2 AA 64 8F 0C 1                                 8 93 5F 42 B5 90 E1 2E D7 E5 84 63 3A 4A FE F1 4D 65 38 92 E5 CC 49 96 4A 39 B5                                  CD 75 4B C7 52 50 79 96 23 50 04 1E E
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: C<: #15 HMIP CMD=14  0F 1B 5                                 5 01 62 98 33 E0 BA B6 98 0D EC E2 F2 AA 64 8F 0C 18 93 5F 42 B5 90 E1 2E D7 E5                                  84 63 3A 4A FE F1 4D 65 38 92 E5 CC 49 96 4A 39 B5 CD 75 4B C7 52 50 79 96 23 50                                  04 1E E5 C9 32 68 E8 91 9B 9D
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: C< @46615: bin:FD 00 45 02 0                                 F 14 0F 1B 55 01 62 98 33 E0 BA B6 98 0D EC E2 F2 AA 64 8F 0C 18 93 5F 42 B5 90                                  E1 2E D7 E5 84 63 3A 4A FE F1 4D 65 38 92 E5 CC 49 96 4A 39 B5 CD 75 4B C7 52 50                                  79 96 23 50 04 1E E5 C9 32 68 E8 91
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: C> @46634: #15 HMIP CMD=06                                   01
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: A<: #28 HMIP CMD=06  01
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: A>: #29 HMIP CMD=12
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: MacController::OnDownstreamF                                 rame(#29 HMIP CMD=12  )
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: C<: #16 HMIP CMD=12
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: C< @46638: bin:FD 00 03 02 1                                 0 12 78 44
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: C> @46646: #16 HMIP CMD=06                                   01
Oct 16 16:18:17 homematic-ccu2 user.debug multimac: A<: #29 HMIP CMD=06  01
Oct 16 16:18:24 homematic-ccu2 user.debug multimac: C<: #17 TRX GetDutyCycle
Oct 16 16:18:24 homematic-ccu2 user.debug multimac: C< @53592: bin:FD 00 03 01 1                                 1 03 FE 1D
Oct 16 16:18:24 homematic-ccu2 user.debug multimac: C> @53694: #17 TRX Response                                  Ack 00
Oct 16 16:18:24 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:18:30 homematic-ccu2 user.debug multimac: C> @59374: #0 LLMAC RX @2619                                 2ms 0dBm 3A 86 10 5F 8E A9 00 00 00 0A A0 EB 8D 00 00
Oct 16 16:18:30 homematic-ccu2 user.debug multimac: Bidcos RX: #3A[BC|Ren|WMup]                                  5F8EA9->000000 Info: 0A A0 EB 8D 00 00
Oct 16 16:18:30 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:18:34 homematic-ccu2 user.debug multimac: C<: #18 TRX GetDutyCycle
Oct 16 16:18:34 homematic-ccu2 user.debug multimac: C< @63592: bin:FD 00 03 01 1                                 2 03 F4 1D
Oct 16 16:18:34 homematic-ccu2 user.debug multimac: C> @63694: #18 TRX Response                                  Ack 00
Oct 16 16:18:34 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:18:36 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:18:36 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =init Params = {"xmlrpc_bin://127.0.0.1:1999","100                                 7"} result= nil [iseXmlRpc.cpp:2599]
Oct 16 16:18:36 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallInit: C                                 allXmlrpcMethod failed [iseXmlRpc.cpp:1204]
Oct 16 16:18:36 homematic-ccu2 local0.err ReGaHss: Error: XmlRpcClientThread::Th                                 readFunction(): failed call init for interface=BidCos-RF [iseRTHss.cpp:163]
Oct 16 16:18:41 homematic-ccu2 user.debug multimac: C> @70805: #1 LLMAC RX @ 493                                 5ms -20dBm 81 86 10 62 6F F2 00 00 00 0A A0 E1 8D 00 00
Oct 16 16:18:41 homematic-ccu2 user.debug multimac: Bidcos RX: #81[BC|Ren|WMup]                                  626FF2->000000 Info: 0A A0 E1 8D 00 00
Oct 16 16:18:41 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:18:43 homematic-ccu2 user.info homematic: HConnect VPN Verbindung wird                                  gestartet.
Oct 16 16:18:44 homematic-ccu2 user.debug multimac: C<: #19 TRX GetDutyCycle
Oct 16 16:18:44 homematic-ccu2 user.debug multimac: C< @73592: bin:FD 00 03 01 1                                 3 03 72 1E
Oct 16 16:18:44 homematic-ccu2 user.debug multimac: C> @73694: #19 TRX Response                                  Ack 00
Oct 16 16:18:44 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:18:51 homematic-ccu2 user.debug setclock: Try to get time from 0.de.po                                 ol.ntp.org
Oct 16 16:18:52 homematic-ccu2 user.debug setclock: Tue Oct 16 16:18:52 CEST 201                                 8
Oct 16 16:18:54 homematic-ccu2 user.debug multimac: C<: #20 TRX GetDutyCycle
Oct 16 16:18:54 homematic-ccu2 user.debug multimac: C< @83594: bin:FD 00 03 01 1                                 4 03 E0 1D
Oct 16 16:18:54 homematic-ccu2 user.debug multimac: C> @83695: #20 TRX Response                                  Ack 00
Oct 16 16:18:54 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:19:04 homematic-ccu2 user.debug multimac: C<: #21 TRX GetDutyCycle
Oct 16 16:19:04 homematic-ccu2 user.debug multimac: C< @93594: bin:FD 00 03 01 1                                 5 03 66 1E
Oct 16 16:19:04 homematic-ccu2 user.debug multimac: C> @93696: #21 TRX Response                                  Ack 00
Oct 16 16:19:04 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:19:14 homematic-ccu2 user.debug multimac: C<: #22 TRX GetDutyCycle
Oct 16 16:19:14 homematic-ccu2 user.debug multimac: C< @103594: bin:FD 00 03 01                                  16 03 6C 1E
Oct 16 16:19:14 homematic-ccu2 user.debug multimac: C> @103696: #22 TRX Response                                  Ack 00
Oct 16 16:19:14 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:19:24 homematic-ccu2 user.debug multimac: C<: #23 TRX GetDutyCycle
Oct 16 16:19:24 homematic-ccu2 user.debug multimac: C< @113594: bin:FD 00 03 01                                  17 03 EA 1D
Oct 16 16:19:24 homematic-ccu2 user.debug multimac: C> @113696: #23 TRX Response                                  Ack 00
Oct 16 16:19:24 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:19:24 homematic-ccu2 user.debug multimac: C> @113733: #2 LLMAC RX @153                                 94ms -68dBm 01 86 10 62 6F F7 00 00 00 0A 78 FB 0D 00 40
Oct 16 16:19:24 homematic-ccu2 user.debug multimac: Bidcos RX: #01[BC|Ren|WMup]                                  626FF7->000000 Info: 0A 78 FB 0D 00 40
Oct 16 16:19:24 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:19:34 homematic-ccu2 user.debug multimac: C<: #24 TRX GetDutyCycle
Oct 16 16:19:34 homematic-ccu2 user.debug multimac: C< @123594: bin:FD 00 03 01                                  18 03 C8 1D
Oct 16 16:19:34 homematic-ccu2 user.debug multimac: C> @123695: #24 TRX Response                                  Ack 00
Oct 16 16:19:34 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:19:44 homematic-ccu2 user.debug multimac: C<: #25 TRX GetDutyCycle
Oct 16 16:19:44 homematic-ccu2 user.debug multimac: C< @133595: bin:FD 00 03 01                                  19 03 4E 1E
Oct 16 16:19:44 homematic-ccu2 user.debug multimac: C> @133696: #25 TRX Response                                  Ack 00
Oct 16 16:19:44 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:19:54 homematic-ccu2 user.debug multimac: C<: #26 TRX GetDutyCycle
Oct 16 16:19:54 homematic-ccu2 user.debug multimac: C< @143596: bin:FD 00 03 01                                  1A 03 44 1E
Oct 16 16:19:54 homematic-ccu2 user.debug multimac: C> @143697: #26 TRX Response                                  Ack 00
Oct 16 16:19:54 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:20:01 homematic-ccu2 cron.info crond[69]: crond: USER root pid 507 cmd                                  /bin/sh /usr/local/addons/hconnectvpn/checkaccount.sh >> /dev/null
Oct 16 16:20:03 homematic-ccu2 user.debug multimac: C> @152335: #3 LLMAC RX @215                                 02ms -48dBm EC 86 10 62 6F F8 00 00 00 0A A0 F1 8E 00 00
Oct 16 16:20:03 homematic-ccu2 user.debug multimac: Bidcos RX: #EC[BC|Ren|WMup]                                  626FF8->000000 Info: 0A A0 F1 8E 00 00
Oct 16 16:20:03 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:20:04 homematic-ccu2 user.debug multimac: C<: #27 TRX GetDutyCycle
Oct 16 16:20:04 homematic-ccu2 user.debug multimac: C< @153596: bin:FD 00 03 01                                  1B 03 C2 1D
Oct 16 16:20:04 homematic-ccu2 user.debug multimac: C> @153697: #27 TRX Response                                  Ack 00
Oct 16 16:20:04 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:20:08 homematic-ccu2 user.debug multimac: C> @157874: #4 LLMAC RX @270                                 81ms -47dBm 9D 86 10 62 70 09 00 00 00 0A C8 E9 8E 64 00
Oct 16 16:20:08 homematic-ccu2 user.debug multimac: Bidcos RX: #9D[BC|Ren|WMup]                                  627009->000000 Info: 0A C8 E9 8E 64 00
Oct 16 16:20:08 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:20:14 homematic-ccu2 user.debug multimac: C<: #28 TRX GetDutyCycle
Oct 16 16:20:14 homematic-ccu2 user.debug multimac: C< @163596: bin:FD 00 03 01                                  1C 03 50 1E
Oct 16 16:20:14 homematic-ccu2 user.debug multimac: C> @163698: #28 TRX Response                                  Ack 00
Oct 16 16:20:14 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:20:24 homematic-ccu2 user.debug multimac: C<: #29 TRX GetDutyCycle
Oct 16 16:20:24 homematic-ccu2 user.debug multimac: C< @173596: bin:FD 00 03 01                                  1D 03 D6 1D
Oct 16 16:20:24 homematic-ccu2 user.debug multimac: C> @173599: #29 TRX Response                                  Ack 00
Oct 16 16:20:24 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:20:34 homematic-ccu2 user.debug multimac: C<: #30 TRX GetDutyCycle
Oct 16 16:20:34 homematic-ccu2 user.debug multimac: C< @183596: bin:FD 00 03 01                                  1E 03 DC 1D
Oct 16 16:20:34 homematic-ccu2 user.debug multimac: C> @183697: #30 TRX Response                                  Ack 00
Oct 16 16:20:34 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:20:40 homematic-ccu2 user.debug multimac: C> @189623: #5 LLMAC RX @262                                 85ms -54dBm 3B 86 10 5F 8E A9 00 00 00 0A A0 EB 8D 00 00
Oct 16 16:20:40 homematic-ccu2 user.debug multimac: Bidcos RX: #3B[BC|Ren|WMup]                                  5F8EA9->000000 Info: 0A A0 EB 8D 00 00
Oct 16 16:20:40 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:20:44 homematic-ccu2 user.debug multimac: C<: #31 TRX GetDutyCycle
Oct 16 16:20:44 homematic-ccu2 user.debug multimac: C< @193596: bin:FD 00 03 01                                  1F 03 5A 1E
Oct 16 16:20:44 homematic-ccu2 user.debug multimac: C> @193598: #31 TRX Response                                  Ack 00
Oct 16 16:20:44 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:20:54 homematic-ccu2 user.debug multimac: C<: #32 TRX GetDutyCycle
Oct 16 16:20:54 homematic-ccu2 user.debug multimac: C< @203596: bin:FD 00 03 01                                  20 03 D8 1E
Oct 16 16:20:54 homematic-ccu2 user.debug multimac: C> @203697: #32 TRX Response                                  Ack 00
Oct 16 16:20:54 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:21:02 homematic-ccu2 user.debug multimac: C> @211554: #6 LLMAC RX @156                                 04ms -20dBm 82 86 10 62 6F F2 00 00 00 0A A0 E1 8D 00 00
Oct 16 16:21:02 homematic-ccu2 user.debug multimac: Bidcos RX: #82[BC|Ren|WMup]                                  626FF2->000000 Info: 0A A0 E1 8D 00 00
Oct 16 16:21:02 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:21:04 homematic-ccu2 user.debug multimac: C<: #33 TRX GetDutyCycle
Oct 16 16:21:04 homematic-ccu2 user.debug multimac: C< @213596: bin:FD 00 03 01                                  21 03 5E 1D
Oct 16 16:21:04 homematic-ccu2 user.debug multimac: C> @213698: #33 TRX Response                                  Ack 00
Oct 16 16:21:04 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:21:14 homematic-ccu2 user.debug multimac: C<: #34 TRX GetDutyCycle
Oct 16 16:21:14 homematic-ccu2 user.debug multimac: C< @223596: bin:FD 00 03 01                                  22 03 54 1D
Oct 16 16:21:14 homematic-ccu2 user.debug multimac: C> @223697: #34 TRX Response                                  Ack 00
Oct 16 16:21:14 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:21:24 homematic-ccu2 user.debug multimac: C<: #35 TRX GetDutyCycle
Oct 16 16:21:24 homematic-ccu2 user.debug multimac: C< @233596: bin:FD 00 03 01                                  23 03 D2 1E
Oct 16 16:21:24 homematic-ccu2 user.debug multimac: C> @233598: #35 TRX Response                                  Ack 00
Oct 16 16:21:24 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:21:34 homematic-ccu2 user.debug multimac: C<: #36 TRX GetDutyCycle
Oct 16 16:21:34 homematic-ccu2 user.debug multimac: C< @243596: bin:FD 00 03 01                                  24 03 40 1D
Oct 16 16:21:34 homematic-ccu2 user.debug multimac: C> @243697: #36 TRX Response                                  Ack 00
Oct 16 16:21:34 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:21:44 homematic-ccu2 user.debug multimac: C<: #37 TRX GetDutyCycle
Oct 16 16:21:44 homematic-ccu2 user.debug multimac: C< @253596: bin:FD 00 03 01                                  25 03 C6 1E
Oct 16 16:21:44 homematic-ccu2 user.debug multimac: C> @253698: #37 TRX Response                                  Ack 00
Oct 16 16:21:44 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:21:54 homematic-ccu2 user.debug multimac: C<: #38 TRX GetDutyCycle
Oct 16 16:21:54 homematic-ccu2 user.debug multimac: C< @263597: bin:FD 00 03 01                                  26 03 CC 1E
Oct 16 16:21:54 homematic-ccu2 user.debug multimac: C> @263699: #38 TRX Response                                  Ack 00
Oct 16 16:21:54 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:22:04 homematic-ccu2 user.debug multimac: C<: #39 TRX GetDutyCycle
Oct 16 16:22:04 homematic-ccu2 user.debug multimac: C< @273598: bin:FD 00 03 01                                  27 03 4A 1D
Oct 16 16:22:04 homematic-ccu2 user.debug multimac: C> @273699: #39 TRX Response                                  Ack 00
Oct 16 16:22:04 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:22:06 homematic-ccu2 user.debug multimac: C> @275584: #7 LLMAC RX @145                                 46ms -68dBm ED 86 10 62 6F F8 00 00 00 0A A0 F1 8E 00 00
Oct 16 16:22:06 homematic-ccu2 user.debug multimac: Bidcos RX: #ED[BC|Ren|WMup]                                  626FF8->000000 Info: 0A A0 F1 8E 00 00
Oct 16 16:22:06 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:22:09 homematic-ccu2 user.debug multimac: C> @278729: #8 LLMAC RX @177                                 14ms -47dBm 02 86 10 62 6F F7 00 00 00 0A 78 FB 0D 00 40
Oct 16 16:22:09 homematic-ccu2 user.debug multimac: Bidcos RX: #02[BC|Ren|WMup]                                  626FF7->000000 Info: 0A 78 FB 0D 00 40
Oct 16 16:22:09 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:22:12 homematic-ccu2 user.debug multimac: C> @281873: #9 LLMAC RX @208                                 79ms -48dBm 9E 86 10 62 70 09 00 00 00 0A C8 E9 8E 64 00
Oct 16 16:22:12 homematic-ccu2 user.debug multimac: Bidcos RX: #9E[BC|Ren|WMup]                                  627009->000000 Info: 0A C8 E9 8E 64 00
Oct 16 16:22:12 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:22:14 homematic-ccu2 user.debug multimac: C<: #40 TRX GetDutyCycle
Oct 16 16:22:14 homematic-ccu2 user.debug multimac: C< @283598: bin:FD 00 03 01                                  28 03 68 1D
Oct 16 16:22:14 homematic-ccu2 user.debug multimac: C> @283699: #40 TRX Response                                  Ack 00
Oct 16 16:22:14 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:22:24 homematic-ccu2 user.debug multimac: C<: #41 TRX GetDutyCycle
Oct 16 16:22:24 homematic-ccu2 user.debug multimac: C< @293598: bin:FD 00 03 01                                  29 03 EE 1E
Oct 16 16:22:24 homematic-ccu2 user.debug multimac: C> @293699: #41 TRX Response                                  Ack 00
Oct 16 16:22:24 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:22:34 homematic-ccu2 user.debug multimac: C<: #42 TRX GetDutyCycle
Oct 16 16:22:34 homematic-ccu2 user.debug multimac: C< @303599: bin:FD 00 03 01                                  2A 03 E4 1E
Oct 16 16:22:34 homematic-ccu2 user.debug multimac: C> @303700: #42 TRX Response                                  Ack 00
Oct 16 16:22:34 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:22:44 homematic-ccu2 user.debug multimac: C<: #43 TRX GetDutyCycle
Oct 16 16:22:44 homematic-ccu2 user.debug multimac: C< @313599: bin:FD 00 03 01                                  2B 03 62 1D
Oct 16 16:22:44 homematic-ccu2 user.debug multimac: C> @313701: #43 TRX Response                                  Ack 00
Oct 16 16:22:44 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:22:54 homematic-ccu2 user.debug multimac: C<: #44 TRX GetDutyCycle
Oct 16 16:22:54 homematic-ccu2 user.debug multimac: C< @323600: bin:FD 00 03 01                                  2C 03 F0 1E
Oct 16 16:22:54 homematic-ccu2 user.debug multimac: C> @323701: #44 TRX Response                                  Ack 00
Oct 16 16:22:54 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:23:04 homematic-ccu2 user.debug multimac: C<: #45 TRX GetDutyCycle
Oct 16 16:23:04 homematic-ccu2 user.debug multimac: C< @333601: bin:FD 00 03 01                                  2D 03 76 1D
Oct 16 16:23:04 homematic-ccu2 user.debug multimac: C> @333702: #45 TRX Response                                  Ack 00
Oct 16 16:23:04 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:23:08 homematic-ccu2 user.debug multimac: C> @338060: #10 LLMAC RX @11                                 921ms -54dBm 83 86 10 62 6F F2 00 00 00 0A A0 E1 8D 00 00
Oct 16 16:23:08 homematic-ccu2 user.debug multimac: Bidcos RX: #83[BC|Ren|WMup]                                  626FF2->000000 Info: 0A A0 E1 8D 00 00
Oct 16 16:23:08 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:23:14 homematic-ccu2 user.debug multimac: C<: #46 TRX GetDutyCycle
Oct 16 16:23:14 homematic-ccu2 user.debug multimac: C< @343601: bin:FD 00 03 01                                  2E 03 7C 1D
Oct 16 16:23:14 homematic-ccu2 user.debug multimac: C> @343703: #46 TRX Response                                  Ack 00
Oct 16 16:23:14 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:23:17 homematic-ccu2 user.debug multimac: A>: #176 TRX GetDutyCycle
Oct 16 16:23:17 homematic-ccu2 user.debug multimac: A<: #176 TRX Response Ack 00
Oct 16 16:23:24 homematic-ccu2 user.debug multimac: C<: #47 TRX GetDutyCycle
Oct 16 16:23:24 homematic-ccu2 user.debug multimac: C< @353602: bin:FD 00 03 01                                  2F 03 FA 1E
Oct 16 16:23:24 homematic-ccu2 user.debug multimac: C> @353704: #47 TRX Response                                  Ack 00
Oct 16 16:23:24 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700384"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getValue Params = {"OEQ1700384:4","ACTUAL_TEMPERA                                 TURE"} result= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetValu                                 e: CallXmlrpcMethod failed [iseXmlRpc.cpp:1432]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseHssDP::ReadValue: C                                 allGetValue failed; sVal = 0.000000 [iseDOMdpHSS.cpp:130]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getValue Params = {"OEQ1700384:4","SET_TEMPERATUR                                 E"} result= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetValu                                 e: CallXmlrpcMethod failed [iseXmlRpc.cpp:1432]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseHssDP::ReadValue: C                                 allGetValue failed; sVal = 0.000000 [iseDOMdpHSS.cpp:130]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getValue Params = {"OEQ1700384:4","CONTROL_MODE"}                                  result= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetValu                                 e: CallXmlrpcMethod failed [iseXmlRpc.cpp:1432]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseHssDP::ReadValue: C                                 allGetValue failed; sVal = 0 [iseDOMdpHSS.cpp:130]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getValue Params = {"OEQ1700384:4","PARTY_TEMPERAT                                 URE"} result= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetValu                                 e: CallXmlrpcMethod failed [iseXmlRpc.cpp:1432]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseHssDP::ReadValue: C                                 allGetValue failed; sVal = 0.000000 [iseDOMdpHSS.cpp:130]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getValue Params = {"OEQ1700384:4","PARTY_START_TI                                 ME"} result= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetValu                                 e: CallXmlrpcMethod failed [iseXmlRpc.cpp:1432]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseHssDP::ReadValue: C                                 allGetValue failed; sVal = 0 [iseDOMdpHSS.cpp:130]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getValue Params = {"OEQ1700384:4","PARTY_START_DA                                 Y"} result= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetValu                                 e: CallXmlrpcMethod failed [iseXmlRpc.cpp:1432]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseHssDP::ReadValue: C                                 allGetValue failed; sVal = 0 [iseDOMdpHSS.cpp:130]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getValue Params = {"OEQ1700384:4","PARTY_START_MO                                 NTH"} result= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetValu                                 e: CallXmlrpcMethod failed [iseXmlRpc.cpp:1432]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseHssDP::ReadValue: C                                 allGetValue failed; sVal = 0 [iseDOMdpHSS.cpp:130]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getValue Params = {"OEQ1700384:4","PARTY_START_YE                                 AR"} result= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetValu                                 e: CallXmlrpcMethod failed [iseXmlRpc.cpp:1432]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseHssDP::ReadValue: C                                 allGetValue failed; sVal = 0 [iseDOMdpHSS.cpp:130]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getValue Params = {"OEQ1700384:4","PARTY_STOP_TIM                                 E"} result= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetValu                                 e: CallXmlrpcMethod failed [iseXmlRpc.cpp:1432]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseHssDP::ReadValue: C                                 allGetValue failed; sVal = 0 [iseDOMdpHSS.cpp:130]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getValue Params = {"OEQ1700384:4","PARTY_STOP_DAY                                 "} result= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetValu                                 e: CallXmlrpcMethod failed [iseXmlRpc.cpp:1432]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseHssDP::ReadValue: C                                 allGetValue failed; sVal = 0 [iseDOMdpHSS.cpp:130]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getValue Params = {"OEQ1700384:4","PARTY_STOP_MON                                 TH"} result= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetValu                                 e: CallXmlrpcMethod failed [iseXmlRpc.cpp:1432]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseHssDP::ReadValue: C                                 allGetValue failed; sVal = 0 [iseDOMdpHSS.cpp:130]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getValue Params = {"OEQ1700384:4","PARTY_STOP_YEA                                 R"} result= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetValu                                 e: CallXmlrpcMethod failed [iseXmlRpc.cpp:1432]
Oct 16 16:23:24 homematic-ccu2 local0.err ReGaHss: Error: IseHssDP::ReadValue: C                                 allGetValue failed; sVal = 0 [iseDOMdpHSS.cpp:130]
Oct 16 16:23:26 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:26 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =setValue Params = {"OEQ1700384:4","AUTO_MODE",tru                                 e} result= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:26 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallSetValu                                 e: CallXmlrpcMethod failed [iseXmlRpc.cpp:1502]
Oct 16 16:23:26 homematic-ccu2 local0.err ReGaHss: Error: IseHssDP::WriteValue:                                  CallSetValue failed; address = OEQ1700384:4 [iseDOMdpHSS.cpp:77]
Oct 16 16:23:27 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:27 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =setValue Params = {"OEQ1700384:4","AUTO_MODE",tru                                 e} result= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:27 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallSetValu                                 e: CallXmlrpcMethod failed [iseXmlRpc.cpp:1502]
Oct 16 16:23:27 homematic-ccu2 local0.err ReGaHss: Error: IseHssDP::WriteValue:                                  CallSetValue failed; address = OEQ1700384:4 [iseDOMdpHSS.cpp:77]
Oct 16 16:23:27 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:27 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =setValue Params = {"OEQ1700384:4","MANU_MODE",0.0                                 00000} result= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:27 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallSetValu                                 e: CallXmlrpcMethod failed [iseXmlRpc.cpp:1502]
Oct 16 16:23:27 homematic-ccu2 local0.err ReGaHss: Error: IseHssDP::WriteValue:                                  CallSetValue failed; address = OEQ1700384:4 [iseDOMdpHSS.cpp:77]
Oct 16 16:23:28 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:28 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =setValue Params = {"OEQ1700384:4","AUTO_MODE",tru                                 e} result= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:28 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallSetValu                                 e: CallXmlrpcMethod failed [iseXmlRpc.cpp:1502]
Oct 16 16:23:28 homematic-ccu2 local0.err ReGaHss: Error: IseHssDP::WriteValue:                                  CallSetValue failed; address = OEQ1700384:4 [iseDOMdpHSS.cpp:77]
Oct 16 16:23:32 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:32 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =setValue Params = {"OEQ1700384:4","LOWERING_MODE"                                 ,true} result= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:32 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallSetValu                                 e: CallXmlrpcMethod failed [iseXmlRpc.cpp:1502]
Oct 16 16:23:32 homematic-ccu2 local0.err ReGaHss: Error: IseHssDP::WriteValue:                                  CallSetValue failed; address = OEQ1700384:4 [iseDOMdpHSS.cpp:77]
Oct 16 16:23:32 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:32 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =setValue Params = {"OEQ1700384:4","LOWERING_MODE"                                 ,true} result= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:32 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallSetValu                                 e: CallXmlrpcMethod failed [iseXmlRpc.cpp:1502]
Oct 16 16:23:32 homematic-ccu2 local0.err ReGaHss: Error: IseHssDP::WriteValue:                                  CallSetValue failed; address = OEQ1700384:4 [iseDOMdpHSS.cpp:77]
Oct 16 16:23:33 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:33 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =setValue Params = {"OEQ1700384:4","MANU_MODE",4.5                                 00000} result= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:33 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallSetValu                                 e: CallXmlrpcMethod failed [iseXmlRpc.cpp:1502]
Oct 16 16:23:33 homematic-ccu2 local0.err ReGaHss: Error: IseHssDP::WriteValue:                                  CallSetValue failed; address = OEQ1700384:4 [iseDOMdpHSS.cpp:77]
Oct 16 16:23:34 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:34 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =setValue Params = {"OEQ1700384:4","MANU_MODE",30.                                 500000} result= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:34 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallSetValu                                 e: CallXmlrpcMethod failed [iseXmlRpc.cpp:1502]
Oct 16 16:23:34 homematic-ccu2 local0.err ReGaHss: Error: IseHssDP::WriteValue:                                  CallSetValue failed; address = OEQ1700384:4 [iseDOMdpHSS.cpp:77]
Oct 16 16:23:34 homematic-ccu2 user.debug multimac: C<: #48 TRX GetDutyCycle
Oct 16 16:23:34 homematic-ccu2 user.debug multimac: C< @363602: bin:FD 00 03 01                                  30 03 38 1D
Oct 16 16:23:34 homematic-ccu2 user.debug multimac: C> @363704: #48 TRX Response                                  Ack 00
Oct 16 16:23:34 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:23:34 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:34 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =setValue Params = {"OEQ1700384:4","COMFORT_MODE",                                 true} result= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:34 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallSetValu                                 e: CallXmlrpcMethod failed [iseXmlRpc.cpp:1502]
Oct 16 16:23:34 homematic-ccu2 local0.err ReGaHss: Error: IseHssDP::WriteValue:                                  CallSetValue failed; address = OEQ1700384:4 [iseDOMdpHSS.cpp:77]
Oct 16 16:23:35 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:35 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =setValue Params = {"OEQ1700384:4","COMFORT_MODE",                                 true} result= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:35 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallSetValu                                 e: CallXmlrpcMethod failed [iseXmlRpc.cpp:1502]
Oct 16 16:23:35 homematic-ccu2 local0.err ReGaHss: Error: IseHssDP::WriteValue:                                  CallSetValue failed; address = OEQ1700384:4 [iseDOMdpHSS.cpp:77]
Oct 16 16:23:36 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:36 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =setValue Params = {"OEQ1700384:4","LOWERING_MODE"                                 ,true} result= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:36 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallSetValu                                 e: CallXmlrpcMethod failed [iseXmlRpc.cpp:1502]
Oct 16 16:23:36 homematic-ccu2 local0.err ReGaHss: Error: IseHssDP::WriteValue:                                  CallSetValue failed; address = OEQ1700384:4 [iseDOMdpHSS.cpp:77]
Oct 16 16:23:37 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:37 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =setValue Params = {"OEQ1700384:4","COMFORT_MODE",                                 true} result= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:37 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallSetValu                                 e: CallXmlrpcMethod failed [iseXmlRpc.cpp:1502]
Oct 16 16:23:37 homematic-ccu2 local0.err ReGaHss: Error: IseHssDP::WriteValue:                                  CallSetValue failed; address = OEQ1700384:4 [iseDOMdpHSS.cpp:77]
Oct 16 16:23:37 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:37 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =setValue Params = {"OEQ1700384:4","LOWERING_MODE"                                 ,true} result= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:37 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallSetValu                                 e: CallXmlrpcMethod failed [iseXmlRpc.cpp:1502]
Oct 16 16:23:37 homematic-ccu2 local0.err ReGaHss: Error: IseHssDP::WriteValue:                                  CallSetValue failed; address = OEQ1700384:4 [iseDOMdpHSS.cpp:77]
Oct 16 16:23:40 homematic-ccu2 user.debug multimac: C> @369627: #11 LLMAC RX @10                                 941ms -68dBm 3C 86 10 5F 8E A9 00 00 00 0A A0 EB 8D 00 00
Oct 16 16:23:40 homematic-ccu2 user.debug multimac: Bidcos RX: #3C[BC|Ren|WMup]                                  5F8EA9->000000 Info: 0A A0 EB 8D 00 00
Oct 16 16:23:40 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700463"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700463"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700463"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700377"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700377"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700377"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"BidCoS-RF"} resul                                 t= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"BidCoS-RF"} resul                                 t= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"BidCoS-RF"} resul                                 t= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700384"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700384"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700384"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700379"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700379"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700379"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700397"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700397"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700397"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1701845"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1701845"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1701845"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:41 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700463"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700463"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700463"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700377"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700377"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700377"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"BidCoS-RF"} resul                                 t= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"BidCoS-RF"} resul                                 t= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"BidCoS-RF"} resul                                 t= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700384"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700384"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700384"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700379"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700379"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700379"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700397"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700397"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700397"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1701845"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1701845"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1701845"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:44 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:44 homematic-ccu2 user.debug multimac: C<: #49 TRX GetDutyCycle
Oct 16 16:23:44 homematic-ccu2 user.debug multimac: C< @373603: bin:FD 00 03 01                                  31 03 BE 1E
Oct 16 16:23:44 homematic-ccu2 user.debug multimac: C> @373704: #49 TRX Response                                  Ack 00
Oct 16 16:23:44 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700463"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700463"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700463"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700377"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700377"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700377"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"BidCoS-RF"} resul                                 t= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"BidCoS-RF"} resul                                 t= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"BidCoS-RF"} resul                                 t= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700384"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700384"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700384"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700379"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700379"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700379"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700397"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700397"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1700397"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1701845"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1701845"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: XmlRpc: Error in XmlRp                                 cClient::writeRequest: write error (error 111). [iseXmlRpc.h:281]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallXmlrpcM                                 ethod: execute failed; method =getDeviceDescription Params = {"OEQ1701845"} resu                                 lt= nil [iseXmlRpc.cpp:2599]
Oct 16 16:23:45 homematic-ccu2 local0.err ReGaHss: Error: IseXmlRpc::CallGetDevi                                 ceDescription: CallXmlrpcMethod failed [iseXmlRpc.cpp:2189]
Oct 16 16:23:54 homematic-ccu2 user.debug multimac: C<: #50 TRX GetDutyCycle
Oct 16 16:23:54 homematic-ccu2 user.debug multimac: C< @383603: bin:FD 00 03 01                                  32 03 B4 1E
Oct 16 16:23:54 homematic-ccu2 user.debug multimac: C> @383705: #50 TRX Response                                  Ack 00
Oct 16 16:23:54 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:24:04 homematic-ccu2 user.debug multimac: C<: #51 TRX GetDutyCycle
Oct 16 16:24:04 homematic-ccu2 user.debug multimac: C< @393603: bin:FD 00 03 01                                  33 03 32 1D
Oct 16 16:24:04 homematic-ccu2 user.debug multimac: C> @393705: #51 TRX Response                                  Ack 00
Oct 16 16:24:04 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:24:14 homematic-ccu2 user.debug multimac: C<: #52 TRX GetDutyCycle
Oct 16 16:24:14 homematic-ccu2 user.debug multimac: C< @403603: bin:FD 00 03 01                                  34 03 A0 1E
Oct 16 16:24:14 homematic-ccu2 user.debug multimac: C> @403704: #52 TRX Response                                  Ack 00
Oct 16 16:24:14 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:24:24 homematic-ccu2 user.debug multimac: C<: #53 TRX GetDutyCycle
Oct 16 16:24:24 homematic-ccu2 user.debug multimac: C< @413603: bin:FD 00 03 01                                  35 03 26 1D
Oct 16 16:24:24 homematic-ccu2 user.debug multimac: C> @413704: #53 TRX Response                                  Ack 00
Oct 16 16:24:24 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:24:34 homematic-ccu2 user.debug multimac: C<: #54 TRX GetDutyCycle
Oct 16 16:24:34 homematic-ccu2 user.debug multimac: C< @423604: bin:FD 00 03 01                                  36 03 2C 1D
Oct 16 16:24:34 homematic-ccu2 user.debug multimac: C> @423705: #54 TRX Response                                  Ack 00
Oct 16 16:24:34 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:24:40 homematic-ccu2 user.debug multimac: C> @429234: #12 LLMAC RX @ 5                                 431ms -20dBm 03 86 10 62 6F F7 00 00 00 0A 78 FB 0D 00 40
Oct 16 16:24:40 homematic-ccu2 user.debug multimac: Bidcos RX: #03[BC|Ren|WMup]                                  626FF7->000000 Info: 0A 78 FB 0D 00 40
Oct 16 16:24:40 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:24:44 homematic-ccu2 user.debug multimac: C<: #55 TRX GetDutyCycle
Oct 16 16:24:44 homematic-ccu2 user.debug multimac: C< @433605: bin:FD 00 03 01                                  37 03 AA 1E
Oct 16 16:24:44 homematic-ccu2 user.debug multimac: C> @433706: #55 TRX Response                                  Ack 00
Oct 16 16:24:44 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:24:54 homematic-ccu2 user.debug multimac: C<: #56 TRX GetDutyCycle
Oct 16 16:24:54 homematic-ccu2 user.debug multimac: C< @443605: bin:FD 00 03 01                                  38 03 88 1E
Oct 16 16:24:54 homematic-ccu2 user.debug multimac: C> @443706: #56 TRX Response                                  Ack 00
Oct 16 16:24:54 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:24:59 homematic-ccu2 user.debug multimac: C> @448342: #13 LLMAC RX @24                                 671ms -50dBm EE 86 10 62 6F F8 00 00 00 0A A0 F1 8E 00 00
Oct 16 16:24:59 homematic-ccu2 user.debug multimac: Bidcos RX: #EE[BC|Ren|WMup]                                  626FF8->000000 Info: 0A A0 F1 8E 00 00
Oct 16 16:24:59 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:25:04 homematic-ccu2 user.debug multimac: C<: #57 TRX GetDutyCycle
Oct 16 16:25:04 homematic-ccu2 user.debug multimac: C< @453605: bin:FD 00 03 01                                  39 03 0E 1D
Oct 16 16:25:04 homematic-ccu2 user.debug multimac: C> @453707: #57 TRX Response                                  Ack 00
Oct 16 16:25:04 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:25:06 homematic-ccu2 user.debug multimac: C> @455377: #14 LLMAC RX @31                                 756ms -47dBm 9F 86 10 62 70 09 00 00 00 0A C8 E9 8E 64 00
Oct 16 16:25:06 homematic-ccu2 user.debug multimac: Bidcos RX: #9F[BC|Ren|WMup]                                  627009->000000 Info: 0A C8 E9 8E 64 00
Oct 16 16:25:06 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:25:14 homematic-ccu2 user.debug multimac: C<: #58 TRX GetDutyCycle
Oct 16 16:25:14 homematic-ccu2 user.debug multimac: C< @463605: bin:FD 00 03 01                                  3A 03 04 1D
Oct 16 16:25:14 homematic-ccu2 user.debug multimac: C> @463607: #58 TRX Response                                  Ack 00
Oct 16 16:25:14 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:25:24 homematic-ccu2 user.debug multimac: C<: #59 TRX GetDutyCycle
Oct 16 16:25:24 homematic-ccu2 user.debug multimac: C< @473605: bin:FD 00 03 01                                  3B 03 82 1E
Oct 16 16:25:24 homematic-ccu2 user.debug multimac: C> @473707: #59 TRX Response                                  Ack 00
Oct 16 16:25:24 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:25:34 homematic-ccu2 user.debug multimac: C<: #60 TRX GetDutyCycle
Oct 16 16:25:34 homematic-ccu2 user.debug multimac: C< @483605: bin:FD 00 03 01                                  3C 03 10 1D
Oct 16 16:25:34 homematic-ccu2 user.debug multimac: C> @483707: #60 TRX Response                                  Ack 00
Oct 16 16:25:34 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:25:44 homematic-ccu2 user.debug multimac: C<: #61 TRX GetDutyCycle
Oct 16 16:25:44 homematic-ccu2 user.debug multimac: C< @493605: bin:FD 00 03 01                                  3D 03 96 1E
Oct 16 16:25:44 homematic-ccu2 user.debug multimac: C> @493707: #61 TRX Response                                  Ack 00
Oct 16 16:25:44 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:25:54 homematic-ccu2 user.debug multimac: C<: #62 TRX GetDutyCycle
Oct 16 16:25:54 homematic-ccu2 user.debug multimac: C< @503605: bin:FD 00 03 01                                  3E 03 9C 1E
Oct 16 16:25:54 homematic-ccu2 user.debug multimac: C> @503707: #62 TRX Response                                  Ack 00
Oct 16 16:25:54 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:26:04 homematic-ccu2 user.debug multimac: C<: #63 TRX GetDutyCycle
Oct 16 16:26:04 homematic-ccu2 user.debug multimac: C< @513605: bin:FD 00 03 01                                  3F 03 1A 1D
Oct 16 16:26:04 homematic-ccu2 user.debug multimac: C> @513707: #63 TRX Response                                  Ack 00
Oct 16 16:26:04 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:26:04 homematic-ccu2 user.debug multimac: C> @514064: #15 LLMAC RX @25                                 318ms -54dBm 84 86 10 62 6F F2 00 00 00 0A A0 E0 8D 00 00
Oct 16 16:26:04 homematic-ccu2 user.debug multimac: Bidcos RX: #84[BC|Ren|WMup]                                  626FF2->000000 Info: 0A A0 E0 8D 00 00
Oct 16 16:26:04 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:26:14 homematic-ccu2 user.debug multimac: C<: #64 TRX GetDutyCycle
Oct 16 16:26:14 homematic-ccu2 user.debug multimac: C< @523605: bin:FD 00 03 01                                  40 03 18 1B
Oct 16 16:26:14 homematic-ccu2 user.debug multimac: C> @523706: #64 TRX Response                                  Ack 00
Oct 16 16:26:14 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:26:24 homematic-ccu2 user.debug multimac: C<: #65 TRX GetDutyCycle
Oct 16 16:26:24 homematic-ccu2 user.debug multimac: C< @533605: bin:FD 00 03 01                                  41 03 9E 18
Oct 16 16:26:24 homematic-ccu2 user.debug multimac: C> @533707: #65 TRX Response                                  Ack 00
Oct 16 16:26:24 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:26:26 homematic-ccu2 user.debug multimac: C> @535130: #16 LLMAC RX @13                                 762ms -68dBm 3D 86 10 5F 8E A9 00 00 00 0A A0 EB 8D 00 00
Oct 16 16:26:26 homematic-ccu2 user.debug multimac: Bidcos RX: #3D[BC|Ren|WMup]                                  5F8EA9->000000 Info: 0A A0 EB 8D 00 00
Oct 16 16:26:26 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:26:34 homematic-ccu2 user.debug multimac: C<: #66 TRX GetDutyCycle
Oct 16 16:26:34 homematic-ccu2 user.debug multimac: C< @543605: bin:FD 00 03 01                                  42 03 94 18
Oct 16 16:26:34 homematic-ccu2 user.debug multimac: C> @543706: #66 TRX Response                                  Ack 00
Oct 16 16:26:34 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:26:44 homematic-ccu2 user.debug multimac: C<: #67 TRX GetDutyCycle
Oct 16 16:26:44 homematic-ccu2 user.debug multimac: C< @553605: bin:FD 00 03 01                                  43 03 12 1B
Oct 16 16:26:44 homematic-ccu2 user.debug multimac: C> @553706: #67 TRX Response                                  Ack 00
Oct 16 16:26:44 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:26:54 homematic-ccu2 user.debug multimac: C<: #68 TRX GetDutyCycle
Oct 16 16:26:54 homematic-ccu2 user.debug multimac: C< @563605: bin:FD 00 03 01                                  44 03 80 18
Oct 16 16:26:54 homematic-ccu2 user.debug multimac: C> @563707: #68 TRX Response                                  Ack 00
Oct 16 16:26:54 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:26:56 homematic-ccu2 user.debug multimac: C> @565489: #17 LLMAC RX @11                                 563ms -20dBm 04 86 10 62 6F F7 00 00 00 0A 78 FB 0D 00 40
Oct 16 16:26:56 homematic-ccu2 user.debug multimac: Bidcos RX: #04[BC|Ren|WMup]                                  626FF7->000000 Info: 0A 78 FB 0D 00 40
Oct 16 16:26:56 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:27:04 homematic-ccu2 user.debug multimac: C<: #69 TRX GetDutyCycle
Oct 16 16:27:04 homematic-ccu2 user.debug multimac: C< @573605: bin:FD 00 03 01                                  45 03 06 1B
Oct 16 16:27:04 homematic-ccu2 user.debug multimac: C> @573707: #69 TRX Response                                  Ack 00
Oct 16 16:27:04 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:27:14 homematic-ccu2 user.debug multimac: C<: #70 TRX GetDutyCycle
Oct 16 16:27:14 homematic-ccu2 user.debug multimac: C< @583605: bin:FD 00 03 01                                  46 03 0C 1B
Oct 16 16:27:14 homematic-ccu2 user.debug multimac: C> @583706: #70 TRX Response                                  Ack 00
Oct 16 16:27:14 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:27:24 homematic-ccu2 user.debug multimac: C<: #71 TRX GetDutyCycle
Oct 16 16:27:24 homematic-ccu2 user.debug multimac: C< @593605: bin:FD 00 03 01                                  47 03 8A 18
Oct 16 16:27:24 homematic-ccu2 user.debug multimac: C> @593706: #71 TRX Response                                  Ack 00
Oct 16 16:27:24 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:27:34 homematic-ccu2 user.debug multimac: C<: #72 TRX GetDutyCycle
Oct 16 16:27:34 homematic-ccu2 user.debug multimac: C< @603605: bin:FD 00 03 01                                  48 03 A8 18
Oct 16 16:27:34 homematic-ccu2 user.debug multimac: C> @603706: #72 TRX Response                                  Ack 00
Oct 16 16:27:34 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:27:37 homematic-ccu2 user.debug multimac: C> @606600: #18 LLMAC RX @20                                 191ms -49dBm EF 86 10 62 6F F8 00 00 00 0A A0 F1 8E 00 00
Oct 16 16:27:37 homematic-ccu2 user.debug multimac: Bidcos RX: #EF[BC|Ren|WMup]                                  626FF8->000000 Info: 0A A0 F1 8E 00 00
Oct 16 16:27:37 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:27:44 homematic-ccu2 user.debug multimac: C<: #73 TRX GetDutyCycle
Oct 16 16:27:44 homematic-ccu2 user.debug multimac: C< @613605: bin:FD 00 03 01                                  49 03 2E 1B
Oct 16 16:27:44 homematic-ccu2 user.debug multimac: C> @613707: #73 TRX Response                                  Ack 00
Oct 16 16:27:44 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:27:45 homematic-ccu2 user.debug multimac: C> @614384: #19 LLMAC RX @28                                 029ms -47dBm A0 86 10 62 70 09 00 00 00 0A C8 E9 8E 64 00
Oct 16 16:27:45 homematic-ccu2 user.debug multimac: Bidcos RX: #A0[BC|Ren|WMup]                                  627009->000000 Info: 0A C8 E9 8E 64 00
Oct 16 16:27:45 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:27:54 homematic-ccu2 user.debug multimac: C<: #74 TRX GetDutyCycle
Oct 16 16:27:54 homematic-ccu2 user.debug multimac: C< @623605: bin:FD 00 03 01                                  4A 03 24 1B
Oct 16 16:27:54 homematic-ccu2 user.debug multimac: C> @623707: #74 TRX Response                                  Ack 00
Oct 16 16:27:54 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:28:04 homematic-ccu2 user.debug multimac: C<: #75 TRX GetDutyCycle
Oct 16 16:28:04 homematic-ccu2 user.debug multimac: C< @633605: bin:FD 00 03 01                                  4B 03 A2 18
Oct 16 16:28:04 homematic-ccu2 user.debug multimac: C> @633707: #75 TRX Response                                  Ack 00
Oct 16 16:28:04 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:28:14 homematic-ccu2 user.debug multimac: C<: #76 TRX GetDutyCycle
Oct 16 16:28:14 homematic-ccu2 user.debug multimac: C< @643605: bin:FD 00 03 01                                  4C 03 30 1B
Oct 16 16:28:14 homematic-ccu2 user.debug multimac: C> @643707: #76 TRX Response                                  Ack 00
Oct 16 16:28:14 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:28:17 homematic-ccu2 user.debug multimac: A>: #177 TRX GetDutyCycle
Oct 16 16:28:17 homematic-ccu2 user.debug multimac: A<: #177 TRX Response Ack 00
Oct 16 16:28:24 homematic-ccu2 user.debug multimac: C<: #77 TRX GetDutyCycle
Oct 16 16:28:24 homematic-ccu2 user.debug multimac: C< @653606: bin:FD 00 03 01                                  4D 03 B6 18
Oct 16 16:28:24 homematic-ccu2 user.debug multimac: C> @653608: #77 TRX Response                                  Ack 00
Oct 16 16:28:24 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:28:34 homematic-ccu2 user.debug multimac: C<: #78 TRX GetDutyCycle
Oct 16 16:28:34 homematic-ccu2 user.debug multimac: C< @663606: bin:FD 00 03 01                                  4E 03 BC 18
Oct 16 16:28:34 homematic-ccu2 user.debug multimac: C> @663707: #78 TRX Response                                  Ack 00
Oct 16 16:28:34 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:28:44 homematic-ccu2 user.debug multimac: C<: #79 TRX GetDutyCycle
Oct 16 16:28:44 homematic-ccu2 user.debug multimac: C< @673606: bin:FD 00 03 01                                  4F 03 3A 1B
Oct 16 16:28:44 homematic-ccu2 user.debug multimac: C> @673708: #79 TRX Response                                  Ack 00
Oct 16 16:28:44 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:28:46 homematic-ccu2 user.debug multimac: C> @675576: #20 LLMAC RX @24                                 111ms -54dBm 85 86 10 62 6F F2 00 00 00 0A A0 E1 8D 00 00
Oct 16 16:28:46 homematic-ccu2 user.debug multimac: Bidcos RX: #85[BC|Ren|WMup]                                  626FF2->000000 Info: 0A A0 E1 8D 00 00
Oct 16 16:28:46 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:28:54 homematic-ccu2 user.debug multimac: C<: #80 TRX GetDutyCycle
Oct 16 16:28:54 homematic-ccu2 user.debug multimac: C< @683606: bin:FD 00 03 01                                  50 03 F8 18
Oct 16 16:28:54 homematic-ccu2 user.debug multimac: C> @683707: #80 TRX Response                                  Ack 00
Oct 16 16:28:54 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:28:57 homematic-ccu2 user.debug multimac: C> @686138: #21 LLMAC RX @ 1                                 979ms -68dBm 3E 86 10 5F 8E A9 00 00 00 0A A0 EB 8D 00 00
Oct 16 16:28:57 homematic-ccu2 user.debug multimac: Bidcos RX: #3E[BC|Ren|WMup]                                  5F8EA9->000000 Info: 0A A0 EB 8D 00 00
Oct 16 16:28:57 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:28:58 homematic-ccu2 user.debug multimac: C> @687245: #22 LLMAC RX @ 3                                 094ms -20dBm 05 86 10 62 6F F7 00 00 00 0A 78 FB 0D 00 40
Oct 16 16:28:58 homematic-ccu2 user.debug multimac: Bidcos RX: #05[BC|Ren|WMup]                                  626FF7->000000 Info: 0A 78 FB 0D 00 40
Oct 16 16:28:58 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:29:04 homematic-ccu2 user.debug multimac: C<: #81 TRX GetDutyCycle
Oct 16 16:29:04 homematic-ccu2 user.debug multimac: C< @693606: bin:FD 00 03 01                                  51 03 7E 1B
Oct 16 16:29:04 homematic-ccu2 user.debug multimac: C> @693707: #81 TRX Response                                  Ack 00
Oct 16 16:29:04 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:29:14 homematic-ccu2 user.debug multimac: C<: #82 TRX GetDutyCycle
Oct 16 16:29:14 homematic-ccu2 user.debug multimac: C< @703607: bin:FD 00 03 01                                  52 03 74 1B
Oct 16 16:29:14 homematic-ccu2 user.debug multimac: C> @703708: #82 TRX Response                                  Ack 00
Oct 16 16:29:14 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:29:24 homematic-ccu2 user.debug multimac: C<: #83 TRX GetDutyCycle
Oct 16 16:29:24 homematic-ccu2 user.debug multimac: C< @713608: bin:FD 00 03 01                                  53 03 F2 18
Oct 16 16:29:24 homematic-ccu2 user.debug multimac: C> @713709: #83 TRX Response                                  Ack 00
Oct 16 16:29:24 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:29:34 homematic-ccu2 user.debug multimac: C<: #84 TRX GetDutyCycle
Oct 16 16:29:34 homematic-ccu2 user.debug multimac: C< @723608: bin:FD 00 03 01                                  54 03 60 1B
Oct 16 16:29:34 homematic-ccu2 user.debug multimac: C> @723709: #84 TRX Response                                  Ack 00
Oct 16 16:29:34 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:29:44 homematic-ccu2 user.debug multimac: C<: #85 TRX GetDutyCycle
Oct 16 16:29:44 homematic-ccu2 user.debug multimac: C< @733609: bin:FD 00 03 01                                  55 03 E6 18
Oct 16 16:29:44 homematic-ccu2 user.debug multimac: C> @733711: #85 TRX Response                                  Ack 00
Oct 16 16:29:44 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:29:54 homematic-ccu2 user.debug multimac: C<: #86 TRX GetDutyCycle
Oct 16 16:29:54 homematic-ccu2 user.debug multimac: C< @743609: bin:FD 00 03 01                                  56 03 EC 18
Oct 16 16:29:54 homematic-ccu2 user.debug multimac: C> @743710: #86 TRX Response                                  Ack 00
Oct 16 16:29:54 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:30:01 homematic-ccu2 user.debug multimac: C> @750357: #23 LLMAC RX @ 1                                 114ms -49dBm F0 86 10 62 6F F8 00 00 00 0A A0 F1 8E 00 00
Oct 16 16:30:01 homematic-ccu2 user.debug multimac: Bidcos RX: #F0[BC|Ren|WMup]                                  626FF8->000000 Info: 0A A0 F1 8E 00 00
Oct 16 16:30:01 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:30:01 homematic-ccu2 cron.info crond[69]: crond: USER root pid 701 cmd                                  /bin/SetInterfaceClock 127.0.0.1:2001
Oct 16 16:30:01 homematic-ccu2 cron.info crond[69]: crond: USER root pid 702 cmd                                  /bin/sh /usr/local/addons/hconnectvpn/checkaccount.sh >> /dev/null
Oct 16 16:30:04 homematic-ccu2 user.debug multimac: C<: #87 TRX GetDutyCycle
Oct 16 16:30:04 homematic-ccu2 user.debug multimac: C< @753609: bin:FD 00 03 01                                  57 03 6A 1B
Oct 16 16:30:04 homematic-ccu2 user.debug multimac: C> @753711: #87 TRX Response                                  Ack 00
Oct 16 16:30:04 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:30:10 homematic-ccu2 user.debug multimac: C> @759138: #24 LLMAC RX @ 9                                 957ms -47dBm A1 86 10 62 70 09 00 00 00 0A C8 EA 8E 64 00
Oct 16 16:30:10 homematic-ccu2 user.debug multimac: Bidcos RX: #A1[BC|Ren|WMup]                                  627009->000000 Info: 0A C8 EA 8E 64 00
Oct 16 16:30:10 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:30:14 homematic-ccu2 user.debug multimac: C<: #88 TRX GetDutyCycle
Oct 16 16:30:14 homematic-ccu2 user.debug multimac: C< @763610: bin:FD 00 03 01                                  58 03 48 1B
Oct 16 16:30:14 homematic-ccu2 user.debug multimac: C> @763711: #88 TRX Response                                  Ack 00
Oct 16 16:30:14 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:30:24 homematic-ccu2 user.debug multimac: C<: #89 TRX GetDutyCycle
Oct 16 16:30:24 homematic-ccu2 user.debug multimac: C< @773610: bin:FD 00 03 01                                  59 03 CE 18
Oct 16 16:30:24 homematic-ccu2 user.debug multimac: C> @773712: #89 TRX Response                                  Ack 00
Oct 16 16:30:24 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:30:34 homematic-ccu2 user.debug multimac: C<: #90 TRX GetDutyCycle
Oct 16 16:30:34 homematic-ccu2 user.debug multimac: C< @783610: bin:FD 00 03 01                                  5A 03 C4 18
Oct 16 16:30:34 homematic-ccu2 user.debug multimac: C> @783712: #90 TRX Response                                  Ack 00
Oct 16 16:30:34 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:30:44 homematic-ccu2 user.debug multimac: C<: #91 TRX GetDutyCycle
Oct 16 16:30:44 homematic-ccu2 user.debug multimac: C< @793610: bin:FD 00 03 01                                  5B 03 42 1B
Oct 16 16:30:44 homematic-ccu2 user.debug multimac: C> @793712: #91 TRX Response                                  Ack 00
Oct 16 16:30:44 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:30:54 homematic-ccu2 user.debug multimac: C<: #92 TRX GetDutyCycle
Oct 16 16:30:54 homematic-ccu2 user.debug multimac: C< @803610: bin:FD 00 03 01                                  5C 03 D0 18
Oct 16 16:30:54 homematic-ccu2 user.debug multimac: C> @803712: #92 TRX Response                                  Ack 00
Oct 16 16:30:54 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:31:04 homematic-ccu2 user.debug multimac: C<: #93 TRX GetDutyCycle
Oct 16 16:31:04 homematic-ccu2 user.debug multimac: C< @813610: bin:FD 00 03 01                                  5D 03 56 1B
Oct 16 16:31:04 homematic-ccu2 user.debug multimac: C> @813711: #93 TRX Response                                  Ack 00
Oct 16 16:31:04 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:31:13 homematic-ccu2 user.debug multimac: C> @822581: #25 LLMAC RX @ 8                                 309ms -54dBm 86 86 10 62 6F F2 00 00 00 0A A0 E1 8D 00 00
Oct 16 16:31:13 homematic-ccu2 user.debug multimac: Bidcos RX: #86[BC|Ren|WMup]                                  626FF2->000000 Info: 0A A0 E1 8D 00 00
Oct 16 16:31:13 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:31:13 homematic-ccu2 user.debug multimac: C> @822892: #26 LLMAC RX @ 8                                 622ms -68dBm 3F 86 10 5F 8E A9 00 00 00 0A A0 EB 8D 00 00
Oct 16 16:31:13 homematic-ccu2 user.debug multimac: Bidcos RX: #3F[BC|Ren|WMup]                                  5F8EA9->000000 Info: 0A A0 EB 8D 00 00
Oct 16 16:31:13 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:31:14 homematic-ccu2 user.debug multimac: C<: #94 TRX GetDutyCycle
Oct 16 16:31:14 homematic-ccu2 user.debug multimac: C< @823610: bin:FD 00 03 01                                  5E 03 5C 1B
Oct 16 16:31:14 homematic-ccu2 user.debug multimac: C> @823712: #94 TRX Response                                  Ack 00
Oct 16 16:31:14 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:31:24 homematic-ccu2 user.debug multimac: C<: #95 TRX GetDutyCycle
Oct 16 16:31:24 homematic-ccu2 user.debug multimac: C< @833610: bin:FD 00 03 01                                  5F 03 DA 18
Oct 16 16:31:24 homematic-ccu2 user.debug multimac: C> @833712: #95 TRX Response                                  Ack 00
Oct 16 16:31:24 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:31:34 homematic-ccu2 user.debug multimac: C<: #96 TRX GetDutyCycle
Oct 16 16:31:34 homematic-ccu2 user.debug multimac: C< @843610: bin:FD 00 03 01                                  60 03 58 18
Oct 16 16:31:34 homematic-ccu2 user.debug multimac: C> @843712: #96 TRX Response                                  Ack 00
Oct 16 16:31:34 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:31:44 homematic-ccu2 user.debug multimac: C<: #97 TRX GetDutyCycle
Oct 16 16:31:44 homematic-ccu2 user.debug multimac: C< @853610: bin:FD 00 03 01                                  61 03 DE 1B
Oct 16 16:31:44 homematic-ccu2 user.debug multimac: C> @853712: #97 TRX Response                                  Ack 00
Oct 16 16:31:44 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:31:49 homematic-ccu2 user.debug multimac: C> @858499: #27 LLMAC RX @11                                 710ms -20dBm 06 86 10 62 6F F7 00 00 00 0A 78 FB 0D 00 40
Oct 16 16:31:49 homematic-ccu2 user.debug multimac: Bidcos RX: #06[BC|Ren|WMup]                                  626FF7->000000 Info: 0A 78 FB 0D 00 40
Oct 16 16:31:49 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:31:54 homematic-ccu2 user.debug multimac: C<: #98 TRX GetDutyCycle
Oct 16 16:31:54 homematic-ccu2 user.debug multimac: C< @863610: bin:FD 00 03 01                                  62 03 D4 1B
Oct 16 16:31:54 homematic-ccu2 user.debug multimac: C> @863712: #98 TRX Response                                  Ack 00
Oct 16 16:31:54 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:32:04 homematic-ccu2 user.debug multimac: C<: #99 TRX GetDutyCycle
Oct 16 16:32:04 homematic-ccu2 user.debug multimac: C< @873610: bin:FD 00 03 01                                  63 03 52 18
Oct 16 16:32:04 homematic-ccu2 user.debug multimac: C> @873712: #99 TRX Response                                  Ack 00
Oct 16 16:32:04 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:32:10 homematic-ccu2 user.debug multimac: C> @879861: #28 LLMAC RX @                                   453ms -57dBm F1 86 10 62 6F F8 00 00 00 0A A0 F1 8E 00 00
Oct 16 16:32:10 homematic-ccu2 user.debug multimac: Bidcos RX: #F1[BC|Ren|WMup]                                  626FF8->000000 Info: 0A A0 F1 8E 00 00
Oct 16 16:32:10 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:32:14 homematic-ccu2 user.debug multimac: C<: #100 TRX GetDutyCycle
Oct 16 16:32:14 homematic-ccu2 user.debug multimac: C< @883610: bin:FD 00 03 01                                  64 03 C0 1B
Oct 16 16:32:14 homematic-ccu2 user.debug multimac: C> @883712: #100 TRX Respons                                 e Ack 00
Oct 16 16:32:14 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:32:20 homematic-ccu2 user.debug multimac: C> @889391: #29 LLMAC RX @10                                 050ms -47dBm A2 86 10 62 70 09 00 00 00 0A C8 E9 8E 64 00
Oct 16 16:32:20 homematic-ccu2 user.debug multimac: Bidcos RX: #A2[BC|Ren|WMup]                                  627009->000000 Info: 0A C8 E9 8E 64 00
Oct 16 16:32:20 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:32:24 homematic-ccu2 user.debug multimac: C<: #101 TRX GetDutyCycle
Oct 16 16:32:24 homematic-ccu2 user.debug multimac: C< @893610: bin:FD 00 03 01                                  65 03 46 18
Oct 16 16:32:24 homematic-ccu2 user.debug multimac: C> @893711: #101 TRX Respons                                 e Ack 00
Oct 16 16:32:24 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:32:34 homematic-ccu2 user.debug multimac: C<: #102 TRX GetDutyCycle
Oct 16 16:32:34 homematic-ccu2 user.debug multimac: C< @903610: bin:FD 00 03 01                                  66 03 4C 18
Oct 16 16:32:34 homematic-ccu2 user.debug multimac: C> @903711: #102 TRX Respons                                 e Ack 00
Oct 16 16:32:34 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:32:44 homematic-ccu2 user.debug multimac: C<: #103 TRX GetDutyCycle
Oct 16 16:32:44 homematic-ccu2 user.debug multimac: C< @913610: bin:FD 00 03 01                                  67 03 CA 1B
Oct 16 16:32:44 homematic-ccu2 user.debug multimac: C> @913711: #103 TRX Respons                                 e Ack 00
Oct 16 16:32:44 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:32:54 homematic-ccu2 user.debug multimac: C<: #104 TRX GetDutyCycle
Oct 16 16:32:54 homematic-ccu2 user.debug multimac: C< @923611: bin:FD 00 03 01                                  68 03 E8 1B
Oct 16 16:32:54 homematic-ccu2 user.debug multimac: C> @923712: #104 TRX Respons                                 e Ack 00
Oct 16 16:32:54 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:33:04 homematic-ccu2 user.debug multimac: C<: #105 TRX GetDutyCycle
Oct 16 16:33:04 homematic-ccu2 user.debug multimac: C< @933611: bin:FD 00 03 01                                  69 03 6E 18
Oct 16 16:33:04 homematic-ccu2 user.debug multimac: C> @933713: #105 TRX Respons                                 e Ack 00
Oct 16 16:33:04 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:33:14 homematic-ccu2 user.debug multimac: C<: #106 TRX GetDutyCycle
Oct 16 16:33:14 homematic-ccu2 user.debug multimac: C< @943611: bin:FD 00 03 01                                  6A 03 64 18
Oct 16 16:33:14 homematic-ccu2 user.debug multimac: C> @943713: #106 TRX Respons                                 e Ack 00
Oct 16 16:33:14 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:33:16 homematic-ccu2 user.debug multimac: C> @945144: #30 LLMAC RX @                                   659ms -54dBm 40 86 10 5F 8E A9 00 00 00 0A A0 EB 8D 00 00
Oct 16 16:33:16 homematic-ccu2 user.debug multimac: Bidcos RX: #40[BC|Ren|WMup]                                  5F8EA9->000000 Info: 0A A0 EB 8D 00 00
Oct 16 16:33:16 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:33:17 homematic-ccu2 user.debug multimac: A>: #178 TRX GetDutyCycle
Oct 16 16:33:17 homematic-ccu2 user.debug multimac: A<: #178 TRX Response Ack 00
Oct 16 16:33:24 homematic-ccu2 user.debug multimac: C<: #107 TRX GetDutyCycle
Oct 16 16:33:24 homematic-ccu2 user.debug multimac: C< @953611: bin:FD 00 03 01                                  6B 03 E2 1B
Oct 16 16:33:24 homematic-ccu2 user.debug multimac: C> @953713: #107 TRX Respons                                 e Ack 00
Oct 16 16:33:24 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:33:26 homematic-ccu2 user.debug multimac: C> @955335: #31 LLMAC RX @10                                 921ms -20dBm 87 86 10 62 6F F2 00 00 00 0A A0 E1 8D 00 00
Oct 16 16:33:26 homematic-ccu2 user.debug multimac: Bidcos RX: #87[BC|Ren|WMup]                                  626FF2->000000 Info: 0A A0 E1 8D 00 00
Oct 16 16:33:26 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:33:34 homematic-ccu2 user.debug multimac: C<: #108 TRX GetDutyCycle
Oct 16 16:33:34 homematic-ccu2 user.debug multimac: C< @963611: bin:FD 00 03 01                                  6C 03 70 18
Oct 16 16:33:34 homematic-ccu2 user.debug multimac: C> @963713: #108 TRX Respons                                 e Ack 00
Oct 16 16:33:34 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:33:44 homematic-ccu2 user.debug multimac: C<: #109 TRX GetDutyCycle
Oct 16 16:33:44 homematic-ccu2 user.debug multimac: C< @973611: bin:FD 00 03 01                                  6D 03 F6 1B
Oct 16 16:33:44 homematic-ccu2 user.debug multimac: C> @973713: #109 TRX Respons                                 e Ack 00
Oct 16 16:33:44 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:33:54 homematic-ccu2 user.debug multimac: C<: #110 TRX GetDutyCycle
Oct 16 16:33:54 homematic-ccu2 user.debug multimac: C< @983611: bin:FD 00 03 01                                  6E 03 FC 7C 1B
Oct 16 16:33:54 homematic-ccu2 user.debug multimac: C> @983713: #110 TRX Respons                                 e Ack 00
Oct 16 16:33:54 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:34:04 homematic-ccu2 user.debug multimac: C<: #111 TRX GetDutyCycle
Oct 16 16:34:04 homematic-ccu2 user.debug multimac: C< @993611: bin:FD 00 03 01                                  6F 03 7A 18
Oct 16 16:34:04 homematic-ccu2 user.debug multimac: C> @993713: #111 TRX Respons                                 e Ack 00
Oct 16 16:34:04 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:34:14 homematic-ccu2 user.debug multimac: C<: #112 TRX GetDutyCycle
Oct 16 16:34:14 homematic-ccu2 user.debug multimac: C< @1003611: bin:FD 00 03 01                                  70 03 B8 1B
Oct 16 16:34:14 homematic-ccu2 user.debug multimac: C> @1003712: #112 TRX Respon                                 se Ack 00
Oct 16 16:34:14 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:34:24 homematic-ccu2 user.debug multimac: C<: #113 TRX GetDutyCycle
Oct 16 16:34:24 homematic-ccu2 user.debug multimac: C< @1013611: bin:FD 00 03 01                                  71 03 3E 18
Oct 16 16:34:24 homematic-ccu2 user.debug multimac: C> @1013712: #113 TRX Respon                                 se Ack 00
Oct 16 16:34:24 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:34:26 homematic-ccu2 user.debug multimac: C> @1015501: #32 LLMAC RX @                                  5973ms -68dBm 07 86 10 62 6F F7 00 00 00 0A 78 FA 0D 00 40
Oct 16 16:34:26 homematic-ccu2 user.debug multimac: Bidcos RX: #07[BC|Ren|WMup]                                  626FF7->000000 Info: 0A 78 FA 0D 00 40
Oct 16 16:34:26 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:34:34 homematic-ccu2 user.debug multimac: C<: #114 TRX GetDutyCycle
Oct 16 16:34:34 homematic-ccu2 user.debug multimac: C< @1023611: bin:FD 00 03 01                                  72 03 34 18
Oct 16 16:34:34 homematic-ccu2 user.debug multimac: C> @1023712: #114 TRX Respon                                 se Ack 00
Oct 16 16:34:34 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:34:44 homematic-ccu2 user.debug multimac: C<: #115 TRX GetDutyCycle
Oct 16 16:34:44 homematic-ccu2 user.debug multimac: C< @1033612: bin:FD 00 03 01                                  73 03 B2 1B
Oct 16 16:34:44 homematic-ccu2 user.debug multimac: C> @1033713: #115 TRX Respon                                 se Ack 00
Oct 16 16:34:44 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:34:54 homematic-ccu2 user.debug multimac: C<: #116 TRX GetDutyCycle
Oct 16 16:34:54 homematic-ccu2 user.debug multimac: C< @1043612: bin:FD 00 03 01                                  74 03 20 18
Oct 16 16:34:54 homematic-ccu2 user.debug multimac: C> @1043615: #116 TRX Respon                                 se Ack 00
Oct 16 16:34:54 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:35:04 homematic-ccu2 user.debug multimac: C<: #117 TRX GetDutyCycle
Oct 16 16:35:04 homematic-ccu2 user.debug multimac: C< @1053612: bin:FD 00 03 01                                  75 03 A6 1B
Oct 16 16:35:04 homematic-ccu2 user.debug multimac: C> @1053713: #117 TRX Respon                                 se Ack 00
Oct 16 16:35:04 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:35:09 homematic-ccu2 user.debug multimac: C> @1058864: #33 LLMAC RX @1                                 6873ms -56dBm F2 86 10 62 6F F8 00 00 00 0A A0 F1 8E 00 00
Oct 16 16:35:09 homematic-ccu2 user.debug multimac: Bidcos RX: #F2[BC|Ren|WMup]                                  626FF8->000000 Info: 0A A0 F1 8E 00 00
Oct 16 16:35:09 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:35:14 homematic-ccu2 user.debug multimac: C<: #118 TRX GetDutyCycle
Oct 16 16:35:14 homematic-ccu2 user.debug multimac: C< @1063612: bin:FD 00 03 01                                  76 03 AC 1B
Oct 16 16:35:14 homematic-ccu2 user.debug multimac: C> @1063714: #118 TRX Respon                                 se Ack 00
Oct 16 16:35:14 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:35:20 homematic-ccu2 user.debug multimac: C> @1069141: #34 LLMAC RX @2                                 7223ms -47dBm A3 86 10 62 70 09 00 00 00 0A C8 E9 8E 64 00
Oct 16 16:35:20 homematic-ccu2 user.debug multimac: Bidcos RX: #A3[BC|Ren|WMup]                                  627009->000000 Info: 0A C8 E9 8E 64 00
Oct 16 16:35:20 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:35:24 homematic-ccu2 user.debug multimac: C<: #119 TRX GetDutyCycle
Oct 16 16:35:24 homematic-ccu2 user.debug multimac: C< @1073612: bin:FD 00 03 01                                  77 03 2A 18
Oct 16 16:35:24 homematic-ccu2 user.debug multimac: C> @1073713: #119 TRX Respon                                 se Ack 00
Oct 16 16:35:24 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:35:34 homematic-ccu2 user.debug multimac: C<: #120 TRX GetDutyCycle
Oct 16 16:35:34 homematic-ccu2 user.debug multimac: C< @1083612: bin:FD 00 03 01                                  78 03 08 18
Oct 16 16:35:34 homematic-ccu2 user.debug multimac: C> @1083713: #120 TRX Respon                                 se Ack 00
Oct 16 16:35:34 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:35:44 homematic-ccu2 user.debug multimac: C<: #121 TRX GetDutyCycle
Oct 16 16:35:44 homematic-ccu2 user.debug multimac: C< @1093612: bin:FD 00 03 01                                  79 03 8E 1B
Oct 16 16:35:44 homematic-ccu2 user.debug multimac: C> @1093713: #121 TRX Respon                                 se Ack 00
Oct 16 16:35:44 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:35:54 homematic-ccu2 user.debug multimac: C<: #122 TRX GetDutyCycle
Oct 16 16:35:54 homematic-ccu2 user.debug multimac: C< @1103612: bin:FD 00 03 01                                  7A 03 84 1B
Oct 16 16:35:54 homematic-ccu2 user.debug multimac: C> @1103713: #122 TRX Respon                                 se Ack 00
Oct 16 16:35:54 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:36:04 homematic-ccu2 user.debug multimac: C<: #123 TRX GetDutyCycle
Oct 16 16:36:04 homematic-ccu2 user.debug multimac: C< @1113612: bin:FD 00 03 01                                  7B 03 02 18
Oct 16 16:36:04 homematic-ccu2 user.debug multimac: C> @1113714: #123 TRX Respon                                 se Ack 00
Oct 16 16:36:04 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:36:07 homematic-ccu2 user.debug multimac: C> @1116892: #35 LLMAC RX @                                  9774ms -54dBm 41 86 10 5F 8E A9 00 00 00 0A A0 EB 8D 00 00
Oct 16 16:36:07 homematic-ccu2 user.debug multimac: Bidcos RX: #41[BC|Ren|WMup]                                  5F8EA9->000000 Info: 0A A0 EB 8D 00 00
Oct 16 16:36:07 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:36:14 homematic-ccu2 user.debug multimac: C<: #124 TRX GetDutyCycle
Oct 16 16:36:14 homematic-ccu2 user.debug multimac: C< @1123612: bin:FD 00 03 01                                  7C 03 90 1B
Oct 16 16:36:14 homematic-ccu2 user.debug multimac: C> @1123614: #124 TRX Respon                                 se Ack 00
Oct 16 16:36:14 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:36:24 homematic-ccu2 user.debug multimac: C<: #125 TRX GetDutyCycle
Oct 16 16:36:24 homematic-ccu2 user.debug multimac: C< @1133613: bin:FD 00 03 01                                  7D 03 16 18
Oct 16 16:36:24 homematic-ccu2 user.debug multimac: C> @1133714: #125 TRX Respon                                 se Ack 00
Oct 16 16:36:24 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:36:28 homematic-ccu2 user.debug multimac: C> @1137585: #36 LLMAC RX @3                                 0613ms -20dBm 88 86 10 62 6F F2 00 00 00 0A A0 E1 8D 00 00
Oct 16 16:36:28 homematic-ccu2 user.debug multimac: Bidcos RX: #88[BC|Ren|WMup]                                  626FF2->000000 Info: 0A A0 E1 8D 00 00
Oct 16 16:36:28 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:36:34 homematic-ccu2 user.debug multimac: C<: #126 TRX GetDutyCycle
Oct 16 16:36:34 homematic-ccu2 user.debug multimac: C< @1143613: bin:FD 00 03 01                                  7E 03 1C 18
Oct 16 16:36:34 homematic-ccu2 user.debug multimac: C> @1143715: #126 TRX Respon                                 se Ack 00
Oct 16 16:36:34 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:36:44 homematic-ccu2 user.debug multimac: C<: #127 TRX GetDutyCycle
Oct 16 16:36:44 homematic-ccu2 user.debug multimac: C< @1153614: bin:FD 00 03 01                                  7F 03 9A 1B
Oct 16 16:36:44 homematic-ccu2 user.debug multimac: C> @1153715: #127 TRX Respon                                 se Ack 00
Oct 16 16:36:44 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:36:48 homematic-ccu2 user.debug multimac: C> @1157998: #37 LLMAC RX @1                                 8402ms -68dBm 08 86 10 62 6F F7 00 00 00 0A 78 FA 0D 00 40
Oct 16 16:36:48 homematic-ccu2 user.debug multimac: Bidcos RX: #08[BC|Ren|WMup]                                  626FF7->000000 Info: 0A 78 FA 0D 00 40
Oct 16 16:36:48 homematic-ccu2 user.debug multimac: GetAckActionForIncomingTeleg                                 ram(): Unknown peer, AckAction_NotForUs
Oct 16 16:36:54 homematic-ccu2 user.debug multimac: C<: #128 TRX GetDutyCycle
Oct 16 16:36:54 homematic-ccu2 user.debug multimac: C< @1163614: bin:FD 00 03 01                                  80 03 18 14
Oct 16 16:36:54 homematic-ccu2 user.debug multimac: C> @1163716: #128 TRX Respon                                 se Ack 00
Oct 16 16:36:54 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0
Oct 16 16:37:04 homematic-ccu2 user.debug multimac: C<: #129 TRX GetDutyCycle
Oct 16 16:37:04 homematic-ccu2 user.debug multimac: C< @1173614: bin:FD 00 03 01                                  81 03 9E 17
Oct 16 16:37:04 homematic-ccu2 user.debug multimac: C> @1173715: #129 TRX Respon                                 se Ack 00
Oct 16 16:37:04 homematic-ccu2 user.debug multimac: SubsystemBidcos::CheckDutyCy                                 cleEventThreshold( 0.0, 0.0 ) = 0

Sorry schon mal für´s vollmüllen.

Jemand von Euch noch eine Idee, woran es scheitert?

LG

Dirk

[deimos]

Hi,

das Funkmodul wird korrekt erkannt.

Aufgrund des Logs tippe ich darauf, dass du irgendwann mal YAHM genutzt hast und die im piVCCU Readme angegebenen Aufräumarbeiten der Konfig (Bei Migrationsschritte von YAHM) nicht ausgeführt hast und daher noch eine zur CCU2 inkompatible (bzw. defekte) Konfig hast.

Viele Grüße
Alex

[Bruce001]

Hi Alex,

danke für die schnelle Antwort.

Da ich eine neue SD mit einem komplett neuen Image eingespielt habe, dachte ich meine Konfiguration sei jungfräulich?!? Oder habe ich hier einen Denkfehler?

Die Firmware des Moduls sollte nach dem Flashvorgang bei 1.4 liegen, aber mit Sicherheit weiss ich nur, dass Flashvorgang erfolgreich und dieses Update eingespielt wurde.

Code: Alles auswählen

https://raw.githubusercontent.com/eq-3/occu/ee68faf77e42ed5e3641790b43a710a3301cea7e/firmware/HM-MOD-UART/coprocessor_update.eq3

.

Wenn ich jetzt wieder raspberrymatic draufbügel habe ich vermutlich wieder ein Update des Funkmoduls und damit eine definitive Nichtfunktion unter pivccu oder?

Danke schon mal im Voraus für deine Hilfe. Sofern die Konfig bei Einspielen eines neuen Images erhalten bleibt?!? setzte ich mich gerne noch mal ein paar Stündchen an die Aufräumarbeiten (Im TV kommt eh nur Müll )

Liebe Grüße

Dirk

[deimos]

Hi,

ich gehe mal davon aus, dass du ein CCU Backup eingespielt hast. Oder hast du wirklich ein rein jungfräuliches Image und noch keine Geräte angelernt?

piVCCU und auch RaspberryMatic sorgen beim Booten dafür, dass die richtige Firmware auf das Funkmodul kommt, bei beiden ist das aktuell die 2.8.6. Nur bei YAHM muss man da selber Hand anlegen.

Viele Grüße
Alex