ich hoffe ihr könnt mir weiter helfen, ich suche schon seit Tagen nach einer Lösung.
Ich versuche in meiner CCU3 den genannten Sensor anzulernen. Folgendes habe ich schon Probiert:
PI neustart oder auch Stromlos -> 10 min warten -> Anlern Prozess Starten -> Sensor Werksreset -> Batterie Einlegen -> Warten
Anlern Prozess jeweils über den mit key oder auch den anderen ausprobiert.
Den key mit und ohne - . Welche Schreibweise ist eigentlich richtig ?
Ich hatte noch nie ein HM-IP Gerät eingerichtet, dafür aber "normale" HM sensoren/aktoren.
Code: Alles auswählen
sudo pivccu-info
piVCCU version: 3.43.16-20
Kernel modules: Available
Raw UART dev: Available
Rasp.Pi3 UART: Assigned to GPIO pins
HMRF Hardware: RPI-RF-MOD
HMIP Hardware: RPI-RF-MOD
Board serial: 58A9930081
Radio MAC: unknown
SGTIN: 3014F711A0001F58A9930081
State: RUNNING
PID: 2810
IP: 192.168.178.31
CPU use: 3.07 seconds
BlkIO use: 2.61 MiB
Link: vethpivccu
TX bytes: 13.76 KiB
RX bytes: 47.41 KiB
Total bytes: 61.17 KiB
Code: Alles auswählen
sudo pivccu-attach cat /var/hm_mode
HM_HMIP_ADDRESS=''
HM_HMIP_DEV='RPI-RF-MOD'
HM_HMIP_DEVNODE='/dev/raw-uart'
HM_HMIP_SERIAL='58A9930081'
HM_HMIP_SGTIN='3014F711A0001F58A9930081'
HM_HMIP_VERSION='4.0.16'
HM_HMRF_ADDRESS=''
HM_HMRF_DEV='RPI-RF-MOD'
HM_HMRF_DEVNODE='/dev/raw-uart'
HM_HMRF_SERIAL='58A9930081'
HM_HMRF_VERSION='3.4.8'
HM_HOST='rpi3'
HM_HOST_GPIO_RESET=''
HM_HOST_GPIO_UART='/dev/raw-uart'
HM_LED_GREEN=''
HM_LED_RED=''
HM_LED_YELLOW=''
HM_MODE='NORMAL'
HM_RTC=''
Code: Alles auswählen
sudo pivccu-attach cat /var/log/messages
Mar 26 20:01:03 piVCCU syslog.info syslogd started: BusyBox v1.29.2
Mar 26 20:01:03 piVCCU user.notice kernel: klogd started: BusyBox v1.29.2 (2019-03-15 17:05:46 CET)
Mar 26 20:01:05 piVCCU syslog.info syslogd exiting
Mar 26 20:01:05 ccu3-webui syslog.info syslogd started: BusyBox v1.29.2
Mar 26 20:01:05 ccu3-webui user.notice kernel: klogd started: BusyBox v1.29.2 (2019-03-15 17:05:46 CET)
Mar 26 20:01:05 ccu3-webui daemon.err udhcpc[164]: started, v1.29.2
Mar 26 20:01:05 ccu3-webui daemon.err udhcpc[164]: sending discover
Mar 26 20:01:05 ccu3-webui daemon.err udhcpc[164]: sending select for 192.168.178.31
Mar 26 20:01:06 ccu3-webui daemon.err udhcpc[164]: lease of 192.168.178.31 obtained, lease time 864000
Mar 26 20:01:07 ccu3-webui user.info firewall: iptables v1.6.2: host/network `fc00::' not found Try `iptables -h' or 'iptables --help' for more information.
Mar 26 20:01:07 ccu3-webui user.info firewall: iptables v1.6.2: host/network `fc00::' not found Try `iptables -h' or 'iptables --help' for more information.
Mar 26 20:01:07 ccu3-webui user.info firewall: iptables v1.6.2: host/network `fc00::' not found Try `iptables -h' or 'iptables --help' for more information.
Mar 26 20:01:07 ccu3-webui user.info firewall: iptables v1.6.2: host/network `fc00::' not found Try `iptables -h' or 'iptables --help' for more information.
Mar 26 20:01:07 ccu3-webui user.info firewall: iptables v1.6.2: host/network `fc00::' not found Try `iptables -h' or 'iptables --help' for more information.
Mar 26 20:01:07 ccu3-webui user.info firewall: iptables v1.6.2: host/network `fc00::' not found Try `iptables -h' or 'iptables --help' for more information.
Mar 26 20:01:07 ccu3-webui user.info firewall: iptables v1.6.2: host/network `fc00::' not found Try `iptables -h' or 'iptables --help' for more information.
Mar 26 20:01:07 ccu3-webui user.info firewall: iptables v1.6.2: host/network `fc00::' not found Try `iptables -h' or 'iptables --help' for more information.
Mar 26 20:01:07 ccu3-webui user.info firewall: iptables v1.6.2: host/network `fc00::' not found Try `iptables -h' or 'iptables --help' for more information.
Mar 26 20:01:07 ccu3-webui user.info firewall: iptables v1.6.2: host/network `fc00::' not found Try `iptables -h' or 'iptables --help' for more information.
Mar 26 20:01:07 ccu3-webui user.info firewall: iptables v1.6.2: host/network `fc00::' not found Try `iptables -h' or 'iptables --help' for more information.
Mar 26 20:01:07 ccu3-webui user.info firewall: iptables v1.6.2: host/network `fc00::' not found Try `iptables -h' or 'iptables --help' for more information.
Mar 26 20:01:08 ccu3-webui user.info firewall: iptables v1.6.2: host/network `fc00::' not found Try `iptables -h' or 'iptables --help' for more information.
Mar 26 20:01:08 ccu3-webui user.info firewall: configuration set
Mar 26 20:01:08 ccu3-webui daemon.info ifplugd(eth0)[286]: ifplugd 0.28 initializing.
Mar 26 20:01:08 ccu3-webui daemon.info ifplugd(eth0)[286]: Using interface eth0/DA:AC:7B:66:0A:93 with driver <veth> (version: 1.0)
Mar 26 20:01:08 ccu3-webui daemon.info ifplugd(eth0)[286]: Using detection mode: SIOCETHTOOL
Mar 26 20:01:08 ccu3-webui daemon.info ifplugd(eth0)[286]: Initialization complete, link beat detected.
Mar 26 20:01:08 ccu3-webui daemon.warn ifplugd(eth0)[286]: Could not open /dev/tty, cannot beep.
Mar 26 20:01:08 ccu3-webui daemon.info ifplugd(eth0)[286]: Executing '/etc/ifplugd/ifplugd.action eth0 up'.
Mar 26 20:01:08 ccu3-webui daemon.warn ifplugd(eth0)[286]: client: ifup: interface eth0 already configured
Mar 26 20:01:08 ccu3-webui daemon.info ifplugd(eth0)[286]: Program executed successfully.
Mar 26 20:01:19 ccu3-webui daemon.notice ntpdate[294]: step time server 193.175.73.151 offset -0.000810 sec
Mar 26 20:01:19 ccu3-webui daemon.notice ntpd[295]: ntpd 4.2.8p12@1.3728-o Fri Mar 15 16:04:16 UTC 2019 (1): Starting
Mar 26 20:01:19 ccu3-webui daemon.info ntpd[295]: Command line: /usr/sbin/ntpd -g 0.de.pool.ntp.org 1.de.pool.ntp.org 2.de.pool.ntp.org 3.de.pool.ntp.org
Mar 26 20:01:19 ccu3-webui daemon.info ntpd[297]: proto: precision = 0.521 usec (-21)
Mar 26 20:01:19 ccu3-webui daemon.info ntpd[297]: Listen and drop on 0 v6wildcard [::]:123
Mar 26 20:01:19 ccu3-webui daemon.info ntpd[297]: Listen and drop on 1 v4wildcard 0.0.0.0:123
Mar 26 20:01:19 ccu3-webui daemon.info ntpd[297]: Listen normally on 2 lo 127.0.0.1:123
Mar 26 20:01:19 ccu3-webui daemon.info ntpd[297]: Listen normally on 3 eth0 192.168.178.31:123
Mar 26 20:01:19 ccu3-webui daemon.info ntpd[297]: Listen normally on 4 lo [::1]:123
Mar 26 20:01:19 ccu3-webui daemon.info ntpd[297]: Listening on routing socket on fd #21 for interface updates
Mar 26 20:01:19 ccu3-webui daemon.info ntpd[297]: kernel reports TIME_ERROR: 0x2041: Clock Unsynchronized
Mar 26 20:01:19 ccu3-webui daemon.info ntpd[297]: kernel reports TIME_ERROR: 0x2041: Clock Unsynchronized
Mar 26 20:01:19 ccu3-webui daemon.err xinetd[316]: Unable to read included directory: /etc/config/xinetd.d [file=/etc/xinetd.conf] [line=14]
Mar 26 20:01:19 ccu3-webui daemon.crit xinetd[316]: 316 {init_services} no services. Exiting...
Mar 26 20:01:19 ccu3-webui daemon.info cuxd[352]: write_pid /var/run/cuxd.pid [352]
Mar 26 20:01:19 ccu3-webui user.info homematic: started cux-daemon
Mar 26 20:01:19 ccu3-webui daemon.info cuxd[352]: CUx-Daemon(2.2.0) on CCU(3.43.16) start PID:352
Mar 26 20:01:19 ccu3-webui daemon.info cuxd[352]: load paramsets(/usr/local/addons/cuxd/cuxd.ps) size:16 update(-46s):Tue Mar 26 20:00:33 2019
Mar 26 20:01:19 ccu3-webui daemon.info cuxd[352]: 0 device-paramset(s) loaded ok!
Mar 26 20:01:19 ccu3-webui daemon.info cuxd[352]: write_proxy /var/cache/cuxd_proxy.ini (352 /usr/local/addons/cuxd/ 2.2.0 3.43.16 0)
Mar 26 20:01:19 ccu3-webui daemon.info cuxd[352]: add interface 'CUxD'
Mar 26 20:01:19 ccu3-webui daemon.info cuxd[352]: write interface(1) 'BidCos-RF' to /usr/local/etc/config/InterfacesList.xml
Mar 26 20:01:19 ccu3-webui daemon.info cuxd[352]: write interface(2) 'VirtualDevices' to /usr/local/etc/config/InterfacesList.xml
Mar 26 20:01:19 ccu3-webui daemon.info cuxd[352]: write interface(3) 'HmIP-RF' to /usr/local/etc/config/InterfacesList.xml
Mar 26 20:01:19 ccu3-webui daemon.info cuxd[352]: write interface(4) 'CUxD' to /usr/local/etc/config/InterfacesList.xml
Mar 26 20:01:19 ccu3-webui user.info root: Updating RF Lan Gateway Coprocessor Firmware
Mar 26 20:01:19 ccu3-webui user.debug update-coprocessor: firmware filename is: coprocessor_update_hm_only.eq3
Mar 26 20:01:19 ccu3-webui user.info root: Updating RF Lan Gateway Firmware
Mar 26 20:01:19 ccu3-webui user.info update-lgw-firmware: No gateway found in config file /etc/config/rfd.conf
Mar 26 20:01:19 ccu3-webui user.info kernel: [ 29.681681] eq3loop: created slave mmd_hmip
Mar 26 20:01:19 ccu3-webui user.info kernel: [ 29.681895] eq3loop: created slave mmd_bidcos
Mar 26 20:01:34 ccu3-webui user.info kernel: [ 44.499244] eq3loop: eq3loop_open_slave() mmd_hmip
Mar 26 20:01:34 ccu3-webui user.info kernel: [ 44.508963] eq3loop: eq3loop_open_slave() mmd_hmip
Mar 26 20:01:34 ccu3-webui user.notice kernel: [ 44.511405] eq3loop: eq3loop_ioctl_slave() mmd_hmip: unhandled ioctl 0x5459
Mar 26 20:01:39 ccu3-webui daemon.warn cuxd[352]: process_rpc_request(127.0.0.1) - illegal XMLRPC(listDevices) request
Mar 26 20:01:40 ccu3-webui daemon.warn cuxd[352]: process_rpc_request(127.0.0.1) - illegal XMLRPC(init) request
Mar 26 20:01:59 ccu3-webui daemon.info cuxd[352]: INIT 'xmlrpc_bin://127.0.0.1:31999' '1598'