PIVCCU3 on RPI3 mit Kommunikationsstörung HMIP-BROLL Aktoren

Virtualisierte CCU für Raspberry Pi und Clones

Moderator: Co-Administratoren

Antworten
dtem
Beiträge: 5
Registriert: 15.04.2016, 22:41

PIVCCU3 on RPI3 mit Kommunikationsstörung HMIP-BROLL Aktoren

Beitrag von dtem » 15.07.2019, 15:15

Hallo zusammen,

ich habe eine neue Installation der PIVCCU3 auf einem Raspberry 3b+ mit RPI-RF-MOD, komme von der CCU2.
Soweit läuft auch alles mit den Homematic Geräten aber die neuangeschaften Homematic IP Aktoren bekomme ich nichts ans fliegen :(
Leider meldet die PIVCCU3 nach dem Anlernen der HMIP-Broll Aktoren eine Kommunikationsstörung und das die Gerätekonfiguration zur Übertragung ansteht. Diese Meldungen lassen sich nicht bestätigen. Eine Steuerung der HMIP-Broll geht nurnoch über die Direktverknüpfung über den Taster am Aktor, die Störung lässt sich nicht beheben.
Das ganze kann und habe ich schon mehrfach nachgestellt, indem ich die Aktoren in die Werkseinstellung zurück versetze und ein Backup der CCU einspiel, welches ich vor dem anlernen der HMIP-BROLL Aktoren gemacht habe und dann die HMIP-Broll aktoren wieder anlernen und dann sofort die Fehlermeldung erhalte.

Bin für Hilfe bei der Fehlersuche Dankbar :!:



Code: Alles auswählen

[email protected]:~ $ sudo pivccu-info
piVCCU version: 3.47.10-28
Kernel modules: Available
Raw UART dev:   Available
Rasp.Pi3 UART:  Assigned to GPIO pins
HMRF Hardware:  RPI-RF-MOD
HMIP Hardware:  RPI-RF-MOD
Board serial:   58A9A723EB
Radio MAC:      unknown
SGTIN:          3014F711A0001F58A9A723EB
State:          RUNNING
PID:            2136
IP:             192.168.1.201
CPU use:        35.06 seconds
BlkIO use:      9.73 MiB
Memory use:     127.79 MiB
KMem use:       6.30 MiB
Link:           vethO8CRJ1
 TX bytes:      2.48 MiB
 RX bytes:      362.91 KiB
 Total bytes:   2.83 MiB

Code: Alles auswählen

[email protected]:~ $ sudo pivccu-attach cat /var/hm_mode
HM_HMIP_ADDRESS=''
HM_HMIP_DEV='RPI-RF-MOD'
HM_HMIP_DEVNODE='/dev/raw-uart'
HM_HMIP_SERIAL='58A9A723EB'
HM_HMIP_SGTIN='3014F711A0001F58A9A723EB'
HM_HMIP_VERSION='4.0.20'
HM_HMRF_ADDRESS=''
HM_HMRF_DEV='RPI-RF-MOD'
HM_HMRF_DEVNODE='/dev/raw-uart'
HM_HMRF_SERIAL='58A9A723EB'
HM_HMRF_VERSION='4.0.20'
HM_HOST='rpi3'
HM_HOST_GPIO_RESET=''
HM_HOST_GPIO_UART='/dev/raw-uart'
HM_LED_GREEN=''
HM_LED_RED=''
HM_LED_YELLOW=''
HM_MODE='NORMAL'
HM_RTC=''

Code: Alles auswählen

Jul 14 10:48:31 de.eq3.cbcs.legacy.bidcos.rpc.LegacyServiceHandler INFO  [vert.x-worker-thread-1] (un)registerCallback on LegacyServiceHandler called from url: xmlrpc_bin://127.0.0.1:31999
Jul 14 10:48:31 de.eq3.cbcs.legacy.bidcos.rpc.LegacyServiceHandler INFO  [vert.x-worker-thread-1] init finished
Jul 14 10:48:31 de.eq3.cbcs.legacy.bidcos.rpc.internal.InterfaceInitializer INFO  [vert.x-worker-thread-2] Added InterfaceId: 1237
Jul 14 10:48:31 de.eq3.cbcs.legacy.bidcos.rpc.internal.DeviceUtil INFO  [vert.x-worker-thread-2] updateDevicesForClient 1237 -> 52 device addresses will be deleted
Jul 14 10:48:32 de.eq3.cbcs.legacy.bidcos.rpc.internal.DeviceUtil INFO  [vert.x-worker-thread-2] updateDevicesForClient 1237 -> 52 device addresses will be added
Jul 14 10:52:59 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO  [vert.x-eventloop-thread-1] SYSTEM: 0 Accesspoints in Queue
Jul 14 10:52:59 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO  [vert.x-eventloop-thread-1] SYSTEM: Permanent-/Burstlistener Handler utilization: 0/50 used
Jul 14 10:52:59 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO  [vert.x-eventloop-thread-1] SYSTEM: Eventlistener Handler utilization: 0/50 used
Jul 14 10:54:25 org.apache.http.impl.client.DefaultHttpClient INFO  [vert.x-worker-thread-3] I/O exception (java.net.SocketException) caught when processing request to {}->http://127.0.0.1:39292: Broken pipe (Write failed)
Jul 14 10:54:25 org.apache.http.impl.client.DefaultHttpClient INFO  [vert.x-worker-thread-3] Retrying request to {}->http://127.0.0.1:39292
Jul 14 10:57:59 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO  [vert.x-eventloop-thread-1] SYSTEM: 0 Accesspoints in Queue
Jul 14 10:57:59 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO  [vert.x-eventloop-thread-1] SYSTEM: Permanent-/Burstlistener Handler utilization: 0/50 used
Jul 14 10:57:59 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO  [vert.x-eventloop-thread-1] SYSTEM: Eventlistener Handler utilization: 0/50 used
Jul 14 10:57:59 de.eq3.cbcs.lib.remotecommadapter.device.service.AccessPointWatchdog INFO  [vert.x-eventloop-thread-5] SYSTEM: Access Point Watchdog running periodic connection check...
[email protected]:~ $
[email protected]:~ $ clear
[email protected]:~ $ e.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO  [vert.x-eventloop-thread-1] SYSTEM: Checking all devices on all accesspoints for updates
Jul 14 10:48:02 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-2] SYSTEM: start of LanRoutingWorker succeeded (f7dfc98c-45ea-4d75-9275-d77aa26a164b)
Jul 14 10:48:02 de.eq3.cbcs.lib.lanrouting.UdpServer INFO  [vert.x-worker-thread-0] UDP Routing established on network interface eth0 : 0.0.0.0 (192.168.1.201)
Jul 14 10:48:02 de.eq3.cbcs.lib.hmiptrxcommadapter.internal.RoutingSubsystem WARN  [Thread-6] Received routing key A91AF98C232EFF5312B227C3BD51309E
Jul 14 10:48:02 de.eq3.cbcs.lib.lanrouting.UdpServer INFO  [vert.x-worker-thread-1] UDP Routing multi cast established on network interface eth0 : 192.168.1.201
Jul 14 10:48:02 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-3] SYSTEM: start of LegacyAPIWorker succeeded (3718c350-b79b-4678-a336-919a2e580aba)
Jul 14 10:48:04 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-2] SYSTEM: start of LegacyInitializion succeeded (730e0998-188e-40de-be0a-756a4ff820ad)
Jul 14 10:48:04 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-0] SYSTEM: initial deployment complete _____________________________________________________
Jul 14 10:48:04 de.eq3.cbcs.server.local.LocalServer INFO  [Thread-0] SYSTEM: Bind XML-RPC api to port 32010
Jul 14 10:48:08 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Default MaxEventLoopExecuteTime: 2000000000
Jul 14 10:48:08 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Default BlockedThreadCheckInterval: 1000
Jul 14 10:48:08 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Default MaxWorkerExecuteTime: 60000000000
Jul 14 10:48:08 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Default EventLoopPoolSize: 8
Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [BackendWorker] (1) *worker
-bash: e.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem: command not found
Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [GroupRequestWorker] (1) *worker
Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [DiagramRequestWorker] (1) *worker
Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [StorageRequestWorker] (1) *worker
Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [DeviceFirmwareRequestWorker] (1) *worker
Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [EnergyPriceRequestWorker] (1) *worker
Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [CouplingRequestWorker] (1) *worker
Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [RegaClientWorker] (1) *worker
Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [GroupConfigurationPersistenceFileSystem] (1) *worker
Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [HmIPGatewayManagementRequestWorker] (1) *worker
Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: deploying 10 classes [email protected]:~ $ ead-1] SYSTEM: There are 0 APs queued with updatable devices (RF)teSubsystem INFO  [vert.x-eventloop-thre
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:02 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO  [vert.x-eventloop-thread-1] SYSTEM: There are 0 APs queued with updatable devices (WIRED)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:02 de.eq3.cbcs.lib.lanrouting.UdpServer INFO  [vert.x-worker-thread-3] UDP Routing configuration: trying to bind port 43438 on eth0 0.0.0.0 -> 192.168.1.201
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:02 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-4] SYSTEM: start of LegacyBackendNotificationHandler succeeded (48dc3956-6b99-4903-8ae0-558ac18fdb8f)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:02 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-7] SYSTEM: start of LegacyNotificationHandler succeeded (513c8b6b-dae6-405e-9e72-c4efd16453fe)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:02 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-2] SYSTEM: start of LanRoutingWorker succeeded (f7dfc98c-45ea-4d75-9275-d77aa26a164b)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:02 de.eq3.cbcs.lib.lanrouting.UdpServer INFO  [vert.x-worker-thread-0] UDP Routing established on network interface eth0 : 0.0.0.0 (192.168.1.201)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:02 de.eq3.cbcs.lib.hmiptrxcommadapter.internal.RoutingSubsystem WARN  [Thread-6] Received routing key A91AF98C232EFF5312B227C3BD51309E
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:02 de.eq3.cbcs.lib.lanrouting.UdpServer INFO  [vert.x-worker-thread-1] UDP Routing multi cast established on network interface eth0 : 192.168.1.201
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:02 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-3] SYSTEM: start of LegacyAPIWorker succeeded (3718c350-b79b-4678-a336-919a2e580aba)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:04 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-2] SYSTEM: start of LegacyInitializion succeeded (730e0998-188e-40de-be0a-756a4ff820ad)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:04 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-0] SYSTEM: initial deployment complete _____________________________________________________
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:04 de.eq3.cbcs.server.local.LocalServer INFO  [Thread-0] SYSTEM: Bind XML-RPC api to port 32010
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:08 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Default MaxEventLoopExecuteTime: 2000000000
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:08 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Default BlockedThreadCheckInterval: 1000-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:08 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Default MaxWorkerExecuteTime: 60000000000
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:08 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Default EventLoopPoolSize: 8
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [BackendWorker] (1) *worker
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [GroupRequestWorker] (1) *worker
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [DiagramRequestWorker] (1) *worker
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [StorageRequestWorker] (1) *worker
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [DeviceFirmwareRequestWorker] (1) *worker
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [EnergyPriceRequestWorker] (1) *worker
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [CouplingRequestWorker] (1) *worker
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [RegaClientWorker] (1) *worker
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [GroupConfigurationPersistenceFileSystem] (1) *worker
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [HmIPGatewayManagementRequestWorker] (1) *worker
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: deploying 10 classes to Vert.x
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: 10 VertxDeployers initialized
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-4] SYSTEM: start of BackendWorker succeeded (8cbd147c-cbbb-476c-b0f2-d2142cffb0ff)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-2] SYSTEM: start of GroupConfigurationPersistenceFileSystem succeeded (ca2575dd-c189-4df5-92b7-cabf196fef80)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-2] SYSTEM: start of RegaClientWorker succeeded (ae4c7ef4-2c10-496d-92df-fff28d752aa8)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-1] SYSTEM: start of StorageRequestWorker succeeded (1e040081-3d88-4eac-912f-094a56ca87a2)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-3] SYSTEM: start of CouplingRequestWorker succeeded (22876a80-962b-41ec-884d-c2c267772003)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-1] SYSTEM: start of EnergyPriceRequestWorker succeeded (7511d3ca-b551-43d6-aa53-13fad8c82dbb)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-2] SYSTEM: start of DiagramRequestWorker succeeded (e63a432b-8715-4f8c-b947-5a223da48ee7)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-0] SYSTEM: start of GroupRequestWorker succeeded (3d48b61a-b919-492f-a47a-e42a1116dbdb)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-4] SYSTEM: start of DeviceFirmwareRequestWorker succeeded (72fdbc7e-c70a-49c7-aec9-05281056d448)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-5] SYSTEM: start of HmIPGatewayManagementRequestWorker succeeded (72b7f539-8ae4-4a5e-9c50-e57cb9475f13)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:09 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: initial deployment complete _____________________________________________________
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:09 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Starting HMServer at 127.0.0.1:39292
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:09 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Read Configuration
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:09 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Create Bidcos Dispatcher
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:09 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] InitBidCosCache
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:10 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Create groupDefinitionProvider
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:10 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Create VirtualDeviceHolder
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:10 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Create VirtualDeviceHandlerRega
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:10 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Create GroupAdministrationService
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:10 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Create GroupDeviceDispatcher
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:10 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Create GroupDeviceHandler
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:10 de.eq3.ccu.groupdevice.service.GroupDeviceHandler INFO  [Thread-1] @GroupDeviceHandler - initializing...
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:10 de.eq3.ccu.groupdevice.service.GroupDeviceHandler INFO  [Thread-1] --> created groupDeviceDispatcher (GroupDeviceService to BidCoS (via Dispatcher))
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:10 de.eq3.ccu.groupdevice.service.GroupDeviceHandler INFO  [Thread-1] --> created virtualDeviceHandler (GroupDeviceService to ReGa)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:10 de.eq3.ccu.groupdevice.service.GroupDeviceHandler INFO  [Thread-1] --> got groupDefinitionProvider
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:10 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Create BidCosGroupMemberProvider
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:10 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Init groupAdministrationService
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:10 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Init Virtual OS Device
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:10 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Init ESHLight Bridge
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:11 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Create RrdDatalogging
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:11 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Create MeasurementService
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:11 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Init MeasurementService
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:11 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Create HTTP Server
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:11 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Create BidCos context and start handler
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:11 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Create group context and start handler
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:11 de.eq3.cbcs.legacy.bidcos.rpc.LegacyServiceHandler INFO  [vert.x-worker-thread-3] (un)registerCallback on LegacyServiceHandler called from url: http://127.0.0.1:39292/bidcos
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:11 de.eq3.cbcs.legacy.bidcos.rpc.LegacyServiceHandler INFO  [vert.x-worker-thread-3] init finished
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:11 de.eq3.cbcs.legacy.bidcos.rpc.internal.InterfaceInitializer INFO  [vert.x-worker-thread-0] Added InterfaceId: HmIP-RF_java
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:11 de.eq3.cbcs.legacy.bidcos.rpc.internal.DeviceUtil INFO  [vert.x-worker-thread-0] updateDevicesForClient HmIP-RF_java -> 70 device addresses will be added
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:12 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Starting HMServer done
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:21 de.eq3.ccu.virtualdevice.service.internal.rega.VirtualDeviceHandlerRega INFO  [vert.x-eventloop-thread-5] (un)registerCallback on VirtualDeviceHandlerRega called from url: xmlrpc_bin://127.0.0.1:31999
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:21 de.eq3.ccu.virtualdevice.service.internal.rega.VirtualDeviceHandlerRega INFO  [vert.x-eventloop-thread-5] Added InterfaceId: 1236
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:21 de.eq3.ccu.virtualdevice.service.internal.rega.BackendWorker INFO  [vert.x-worker-thread-12] Execute BackendCommand: de.eq3.ccu.virtualdevice.service.internal.rega.BackendUpdateDevicesCommand
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:31 de.eq3.cbcs.legacy.bidcos.rpc.LegacyServiceHandler INFO  [vert.x-worker-thread-1] (un)registerCallback on LegacyServiceHandler called from url: xmlrpc_bin://127.0.0.1:31999
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:31 de.eq3.cbcs.legacy.bidcos.rpc.LegacyServiceHandler INFO  [vert.x-worker-thread-1] init finished
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:31 de.eq3.cbcs.legacy.bidcos.rpc.internal.InterfaceInitializer INFO  [vert.x-worker-thread-2] Added InterfaceId: 1237
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:31 de.eq3.cbcs.legacy.bidcos.rpc.internal.DeviceUtil INFO  [vert.x-worker-thread-2] updateDevicesForClient 1237 -> 52 device addresses will be deleted
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:32 de.eq3.cbcs.legacy.bidcos.rpc.internal.DeviceUtil INFO  [vert.x-worker-thread-2] updateDevicesForClient 1237 -> 52 device addresses will be added
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:52:59 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO  [vert.x-eventloop-thread-1] SYSTEM: 0 Accesspoints in Queue
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:52:59 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO  [vert.x-eventloop-thread-1] SYSTEM: Permanent-/Burstlistener Handler utilization: 0/50 used
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:52:59 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO  [vert.x-eventloop-thread-1] SYSTEM: Eventlistener Handler utilization: 0/50 used
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:54:25 org.apache.http.impl.client.DefaultHttpClient INFO  [vert.x-worker-thread-3] I/O exception (java.net.SocketException) caught when processing request to {}->http://127.0.0.1:39292: Broken pipe (Write failed)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:54:25 org.apache.http.impl.client.DefaultHttpClient INFO  [vert.x-worker-thread-3] Retrying request to {}->http://127.0.0.1:39292
-bash: http://127.0.0.1:39292: No such file or directory
[email protected]:~ $ Jul 14 10:57:59 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO  [vert.x-eventloop-thread-1] SYSTEM: 0 Accesspoints in Queue
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:57:59 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO  [vert.x-eventloop-thread-1] SYSTEM: Permanent-/Burstlistener Handler utilization: 0/50 used
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:57:59 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO  [vert.x-eventloop-thread-1] SYSTEM: Eventlistener Handler utilization: 0/50 used
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:57:59 de.eq3.cbcs.lib.remotecommadapter.device.service.AccessPointWatchdog INFO  [vert.x-eventloop-thread-5] SYSTEM: Access Point Watchdog running periodic connection check...

Code: Alles auswählen

Jul 14 10:48:31 de.eq3.cbcs.legacy.bidcos.rpc.LegacyServiceHandler INFO  [vert.x-worker-thread-1] (un)registerCallback on LegacyServiceHandler called from url: xmlrpc_bin://127.0.0.1:31999
Jul 14 10:48:31 de.eq3.cbcs.legacy.bidcos.rpc.LegacyServiceHandler INFO  [vert.x-worker-thread-1] init finished
Jul 14 10:48:31 de.eq3.cbcs.legacy.bidcos.rpc.internal.InterfaceInitializer INFO  [vert.x-worker-thread-2] Added InterfaceId: 1237
Jul 14 10:48:31 de.eq3.cbcs.legacy.bidcos.rpc.internal.DeviceUtil INFO  [vert.x-worker-thread-2] updateDevicesForClient 1237 -> 52 device addresses will be deleted
Jul 14 10:48:32 de.eq3.cbcs.legacy.bidcos.rpc.internal.DeviceUtil INFO  [vert.x-worker-thread-2] updateDevicesForClient 1237 -> 52 device addresses will be added
Jul 14 10:52:59 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO  [vert.x-eventloop-thread-1] SYSTEM: 0 Accesspoints in Queue
Jul 14 10:52:59 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO  [vert.x-eventloop-thread-1] SYSTEM: Permanent-/Burstlistener Handler utilization: 0/50 used
Jul 14 10:52:59 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO  [vert.x-eventloop-thread-1] SYSTEM: Eventlistener Handler utilization: 0/50 used
Jul 14 10:54:25 org.apache.http.impl.client.DefaultHttpClient INFO  [vert.x-worker-thread-3] I/O exception (java.net.SocketException) caught when processing request to {}->http://127.0.0.1:39292: Broken pipe (Write failed)
Jul 14 10:54:25 org.apache.http.impl.client.DefaultHttpClient INFO  [vert.x-worker-thread-3] Retrying request to {}->http://127.0.0.1:39292
Jul 14 10:57:59 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO  [vert.x-eventloop-thread-1] SYSTEM: 0 Accesspoints in Queue
Jul 14 10:57:59 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO  [vert.x-eventloop-thread-1] SYSTEM: Permanent-/Burstlistener Handler utilization: 0/50 used
Jul 14 10:57:59 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO  [vert.x-eventloop-thread-1] SYSTEM: Eventlistener Handler utilization: 0/50 used
Jul 14 10:57:59 de.eq3.cbcs.lib.remotecommadapter.device.service.AccessPointWatchdog INFO  [vert.x-eventloop-thread-5] SYSTEM: Access Point Watchdog running periodic connection check...
[email protected]:~ $
[email protected]:~ $ clear
[email protected]raspberrypi:~ $ e.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO  [vert.x-eventloop-thread-1] SYSTEM: Checking all devices on all accesspoints for updates
Jul 14 10:48:02 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-2] SYSTEM: start of LanRoutingWorker succeeded (f7dfc98c-45ea-4d75-9275-d77aa26a164b)
Jul 14 10:48:02 de.eq3.cbcs.lib.lanrouting.UdpServer INFO  [vert.x-worker-thread-0] UDP Routing established on network interface eth0 : 0.0.0.0 (192.168.1.201)
Jul 14 10:48:02 de.eq3.cbcs.lib.hmiptrxcommadapter.internal.RoutingSubsystem WARN  [Thread-6] Received routing key A91AF98C232EFF5312B227C3BD51309E
Jul 14 10:48:02 de.eq3.cbcs.lib.lanrouting.UdpServer INFO  [vert.x-worker-thread-1] UDP Routing multi cast established on network interface eth0 : 192.168.1.201
Jul 14 10:48:02 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-3] SYSTEM: start of LegacyAPIWorker succeeded (3718c350-b79b-4678-a336-919a2e580aba)
Jul 14 10:48:04 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-2] SYSTEM: start of LegacyInitializion succeeded (730e0998-188e-40de-be0a-756a4ff820ad)
Jul 14 10:48:04 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-0] SYSTEM: initial deployment complete _____________________________________________________
Jul 14 10:48:04 de.eq3.cbcs.server.local.LocalServer INFO  [Thread-0] SYSTEM: Bind XML-RPC api to port 32010
Jul 14 10:48:08 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Default MaxEventLoopExecuteTime: 2000000000
Jul 14 10:48:08 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Default BlockedThreadCheckInterval: 1000
Jul 14 10:48:08 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Default MaxWorkerExecuteTime: 60000000000
Jul 14 10:48:08 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Default EventLoopPoolSize: 8
Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [BackendWorker] (1) *worker
-bash: e.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem: command not found
Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [GroupRequestWorker] (1) *worker
Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [DiagramRequestWorker] (1) *worker
Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [StorageRequestWorker] (1) *worker
Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [DeviceFirmwareRequestWorker] (1) *worker
Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [EnergyPriceRequestWorker] (1) *worker
Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [CouplingRequestWorker] (1) *worker
Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [RegaClientWorker] (1) *worker
Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [GroupConfigurationPersistenceFileSystem] (1) *worker
Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [HmIPGatewayManagementRequestWorker] (1) *worker
Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: deploying 10 classes [email protected]:~ $ ead-1] SYSTEM: There are 0 APs queued with updatable devices (RF)teSubsystem INFO  [vert.x-eventloop-thre
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:02 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO  [vert.x-eventloop-thread-1] SYSTEM: There are 0 APs queued with updatable devices (WIRED)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:02 de.eq3.cbcs.lib.lanrouting.UdpServer INFO  [vert.x-worker-thread-3] UDP Routing configuration: trying to bind port 43438 on eth0 0.0.0.0 -> 192.168.1.201
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:02 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-4] SYSTEM: start of LegacyBackendNotificationHandler succeeded (48dc3956-6b99-4903-8ae0-558ac18fdb8f)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:02 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-7] SYSTEM: start of LegacyNotificationHandler succeeded (513c8b6b-dae6-405e-9e72-c4efd16453fe)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:02 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-2] SYSTEM: start of LanRoutingWorker succeeded (f7dfc98c-45ea-4d75-9275-d77aa26a164b)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:02 de.eq3.cbcs.lib.lanrouting.UdpServer INFO  [vert.x-worker-thread-0] UDP Routing established on network interface eth0 : 0.0.0.0 (192.168.1.201)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:02 de.eq3.cbcs.lib.hmiptrxcommadapter.internal.RoutingSubsystem WARN  [Thread-6] Received routing key A91AF98C232EFF5312B227C3BD51309E
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:02 de.eq3.cbcs.lib.lanrouting.UdpServer INFO  [vert.x-worker-thread-1] UDP Routing multi cast established on network interface eth0 : 192.168.1.201
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:02 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-3] SYSTEM: start of LegacyAPIWorker succeeded (3718c350-b79b-4678-a336-919a2e580aba)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:04 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-2] SYSTEM: start of LegacyInitializion succeeded (730e0998-188e-40de-be0a-756a4ff820ad)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:04 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-0] SYSTEM: initial deployment complete _____________________________________________________
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:04 de.eq3.cbcs.server.local.LocalServer INFO  [Thread-0] SYSTEM: Bind XML-RPC api to port 32010
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:08 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Default MaxEventLoopExecuteTime: 2000000000
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:08 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Default BlockedThreadCheckInterval: 1000-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:08 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Default MaxWorkerExecuteTime: 60000000000
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:08 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Default EventLoopPoolSize: 8
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [BackendWorker] (1) *worker
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [GroupRequestWorker] (1) *worker
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [DiagramRequestWorker] (1) *worker
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [StorageRequestWorker] (1) *worker
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [DeviceFirmwareRequestWorker] (1) *worker
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [EnergyPriceRequestWorker] (1) *worker
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [CouplingRequestWorker] (1) *worker
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [RegaClientWorker] (1) *worker
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [GroupConfigurationPersistenceFileSystem] (1) *worker
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: added for deployment [HmIPGatewayManagementRequestWorker] (1) *worker
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: deploying 10 classes to Vert.x
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: 10 VertxDeployers initialized
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-4] SYSTEM: start of BackendWorker succeeded (8cbd147c-cbbb-476c-b0f2-d2142cffb0ff)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-2] SYSTEM: start of GroupConfigurationPersistenceFileSystem succeeded (ca2575dd-c189-4df5-92b7-cabf196fef80)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-2] SYSTEM: start of RegaClientWorker succeeded (ae4c7ef4-2c10-496d-92df-fff28d752aa8)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-1] SYSTEM: start of StorageRequestWorker succeeded (1e040081-3d88-4eac-912f-094a56ca87a2)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-3] SYSTEM: start of CouplingRequestWorker succeeded (22876a80-962b-41ec-884d-c2c267772003)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-1] SYSTEM: start of EnergyPriceRequestWorker succeeded (7511d3ca-b551-43d6-aa53-13fad8c82dbb)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-2] SYSTEM: start of DiagramRequestWorker succeeded (e63a432b-8715-4f8c-b947-5a223da48ee7)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-0] SYSTEM: start of GroupRequestWorker succeeded (3d48b61a-b919-492f-a47a-e42a1116dbdb)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-4] SYSTEM: start of DeviceFirmwareRequestWorker succeeded (72fdbc7e-c70a-49c7-aec9-05281056d448)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:08 de.eq3.cbcs.vertx.management.VertxManager INFO  [vert.x-eventloop-thread-5] SYSTEM: start of HmIPGatewayManagementRequestWorker succeeded (72b7f539-8ae4-4a5e-9c50-e57cb9475f13)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:09 de.eq3.cbcs.vertx.management.VertxManager INFO  [Thread-1] SYSTEM: initial deployment complete _____________________________________________________
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:09 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Starting HMServer at 127.0.0.1:39292
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:09 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Read Configuration
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:09 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Create Bidcos Dispatcher
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:09 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] InitBidCosCache
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:10 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Create groupDefinitionProvider
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:10 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Create VirtualDeviceHolder
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:10 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Create VirtualDeviceHandlerRega
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:10 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Create GroupAdministrationService
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:10 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Create GroupDeviceDispatcher
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:10 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Create GroupDeviceHandler
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:10 de.eq3.ccu.groupdevice.service.GroupDeviceHandler INFO  [Thread-1] @GroupDeviceHandler - initializing...
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:10 de.eq3.ccu.groupdevice.service.GroupDeviceHandler INFO  [Thread-1] --> created groupDeviceDispatcher (GroupDeviceService to BidCoS (via Dispatcher))
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:10 de.eq3.ccu.groupdevice.service.GroupDeviceHandler INFO  [Thread-1] --> created virtualDeviceHandler (GroupDeviceService to ReGa)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:10 de.eq3.ccu.groupdevice.service.GroupDeviceHandler INFO  [Thread-1] --> got groupDefinitionProvider
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:10 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Create BidCosGroupMemberProvider
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:10 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Init groupAdministrationService
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:10 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Init Virtual OS Device
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:10 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Init ESHLight Bridge
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:11 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Create RrdDatalogging
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:11 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Create MeasurementService
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:11 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Init MeasurementService
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:11 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Create HTTP Server
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:11 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Create BidCos context and start handler
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:11 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Create group context and start handler
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:11 de.eq3.cbcs.legacy.bidcos.rpc.LegacyServiceHandler INFO  [vert.x-worker-thread-3] (un)registerCallback on LegacyServiceHandler called from url: http://127.0.0.1:39292/bidcos
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:11 de.eq3.cbcs.legacy.bidcos.rpc.LegacyServiceHandler INFO  [vert.x-worker-thread-3] init finished
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:11 de.eq3.cbcs.legacy.bidcos.rpc.internal.InterfaceInitializer INFO  [vert.x-worker-thread-0] Added InterfaceId: HmIP-RF_java
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:11 de.eq3.cbcs.legacy.bidcos.rpc.internal.DeviceUtil INFO  [vert.x-worker-thread-0] updateDevicesForClient HmIP-RF_java -> 70 device addresses will be added
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:12 de.eq3.ccu.server.BaseHMServer INFO  [Thread-1] Starting HMServer done
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:21 de.eq3.ccu.virtualdevice.service.internal.rega.VirtualDeviceHandlerRega INFO  [vert.x-eventloop-thread-5] (un)registerCallback on VirtualDeviceHandlerRega called from url: xmlrpc_bin://127.0.0.1:31999
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:21 de.eq3.ccu.virtualdevice.service.internal.rega.VirtualDeviceHandlerRega INFO  [vert.x-eventloop-thread-5] Added InterfaceId: 1236
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:21 de.eq3.ccu.virtualdevice.service.internal.rega.BackendWorker INFO  [vert.x-worker-thread-12] Execute BackendCommand: de.eq3.ccu.virtualdevice.service.internal.rega.BackendUpdateDevicesCommand
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:31 de.eq3.cbcs.legacy.bidcos.rpc.LegacyServiceHandler INFO  [vert.x-worker-thread-1] (un)registerCallback on LegacyServiceHandler called from url: xmlrpc_bin://127.0.0.1:31999
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:48:31 de.eq3.cbcs.legacy.bidcos.rpc.LegacyServiceHandler INFO  [vert.x-worker-thread-1] init finished
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:31 de.eq3.cbcs.legacy.bidcos.rpc.internal.InterfaceInitializer INFO  [vert.x-worker-thread-2] Added InterfaceId: 1237
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:31 de.eq3.cbcs.legacy.bidcos.rpc.internal.DeviceUtil INFO  [vert.x-worker-thread-2] updateDevicesForClient 1237 -> 52 device addresses will be deleted
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:48:32 de.eq3.cbcs.legacy.bidcos.rpc.internal.DeviceUtil INFO  [vert.x-worker-thread-2] updateDevicesForClient 1237 -> 52 device addresses will be added
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:52:59 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO  [vert.x-eventloop-thread-1] SYSTEM: 0 Accesspoints in Queue
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:52:59 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO  [vert.x-eventloop-thread-1] SYSTEM: Permanent-/Burstlistener Handler utilization: 0/50 used
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:52:59 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO  [vert.x-eventloop-thread-1] SYSTEM: Eventlistener Handler utilization: 0/50 used
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:54:25 org.apache.http.impl.client.DefaultHttpClient INFO  [vert.x-worker-thread-3] I/O exception (java.net.SocketException) caught when processing request to {}->http://127.0.0.1:39292: Broken pipe (Write failed)
-bash: syntax error near unexpected token `('
[email protected]:~ $ Jul 14 10:54:25 org.apache.http.impl.client.DefaultHttpClient INFO  [vert.x-worker-thread-3] Retrying request to {}->http://127.0.0.1:39292
-bash: http://127.0.0.1:39292: No such file or directory
[email protected]:~ $ Jul 14 10:57:59 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO  [vert.x-eventloop-thread-1] SYSTEM: 0 Accesspoints in Queue
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:57:59 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO  [vert.x-eventloop-thread-1] SYSTEM: Permanent-/Burstlistener Handler utilization: 0/50 used
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:57:59 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO  [vert.x-eventloop-thread-1] SYSTEM: Eventlistener Handler utilization: 0/50 used
-bash: Jul: command not found
[email protected]:~ $ Jul 14 10:57:59 de.eq3.cbcs.lib.remotecommadapter.device.service.AccessPointWatchdog INFO  [vert.x-eventloop-thread-5] SYSTEM: Access Point Watchdog running periodic connection check...

Antworten

Zurück zu „piVCCU“