bei mir läuft das All-in-One Image (pivccu+ioBroker).
Im Log vom IoBroker erscheint regelmäßig die Meldung:
hm-rega.0 2020-04-03 19:16:38.356 error (1348) CCU 192.168.178.46 unreachable
hm-rega.0 2020-04-03 19:16:38.355 error (1348) post request error: connect ETIMEDOUT 192.168.178.46:8181
Es sind alle Updates gemacht und auch ein Neustart brachte keinen Erfolg.
Zur schnellen Aufklärung habe ich folgende Befehle nach Neustart ausgeführt.
Code: Alles auswählen
sudo pivccu-info
piVCCU version: 3.51.6-36
Kernel modules: Available
Raw UART dev: Available
Rasp.Pi UART: Assigned to GPIO pins
HMRF Hardware: HM-MOD-RPI-PCB
HMIP Hardware: HM-MOD-RPI-PCB
Board serial: QEQ0408837
Radio MAC: 0x6d06ea
SGTIN: 3014F711A061A7DA498FA505
State: RUNNING
PID: 797
IP: 192.168.178.46
CPU use: 17.61 seconds
BlkIO use: 62.66 MiB
Memory use: 162.90 MiB
KMem use: 5.33 MiB
Link: vethpivccu
TX bytes: 4.44 MiB
RX bytes: 313.13 KiB
Total bytes: 4.75 MiB
Code: Alles auswählen
sudo pivccu-attach cat /var/hm_mode
HM_HMIP_ADDRESS='0x6d06ea'
HM_HMIP_DEV='HM-MOD-RPI-PCB'
HM_HMIP_DEVNODE='/dev/raw-uart'
HM_HMIP_SERIAL='QEQ0408837'
HM_HMIP_SGTIN='3014F711A061A7DA498FA505'
HM_HMIP_VERSION='2.8.6'
HM_HMRF_ADDRESS='0x6d06ea'
HM_HMRF_DEV='HM-MOD-RPI-PCB'
HM_HMRF_DEVNODE='/dev/raw-uart'
HM_HMRF_SERIAL='QEQ0408837'
HM_HMRF_VERSION='2.8.6'
HM_HOST='rpi3'
HM_HOST_GPIO_RESET=''
HM_HOST_GPIO_UART='/dev/raw-uart'
HM_LED_GREEN=''
HM_LED_RED=''
HM_LED_YELLOW=''
HM_MODE='NORMAL'
HM_RTC=''
Code: Alles auswählen
sudo pivccu-attach cat /var/log/messages
Apr 3 19:22:59 piVCCU syslog.info syslogd started: BusyBox v1.29.2
Apr 3 19:22:59 piVCCU user.notice kernel: klogd started: BusyBox v1.29.2 (2020-01-31 08:51:06 CET)
Apr 3 19:22:59 piVCCU syslog.info syslogd exiting
Apr 3 19:22:59 ccu3-webui syslog.info syslogd started: BusyBox v1.29.2
Apr 3 19:22:59 ccu3-webui user.notice kernel: klogd started: BusyBox v1.29.2 (2020-01-31 08:51:06 CET)
Apr 3 19:22:59 ccu3-webui daemon.err udhcpc[158]: started, v1.29.2
Apr 3 19:22:59 ccu3-webui daemon.err udhcpc[158]: sending discover
Apr 3 19:22:59 ccu3-webui daemon.err udhcpc[158]: sending select for 192.168.178.46
Apr 3 19:23:00 ccu3-webui daemon.err udhcpc[158]: lease of 192.168.178.46 obtained, lease time 864000
Apr 3 19:23:00 ccu3-webui user.info firewall: configuration set
Apr 3 19:23:00 ccu3-webui daemon.info ifplugd(eth0)[248]: ifplugd 0.28 initializing.
Apr 3 19:23:00 ccu3-webui daemon.info ifplugd(eth0)[248]: Using interface eth0/7A:D6:D2:6E:A0:AA with driver <veth> (version: 1.0)
Apr 3 19:23:00 ccu3-webui daemon.info ifplugd(eth0)[248]: Using detection mode: SIOCETHTOOL
Apr 3 19:23:00 ccu3-webui daemon.info ifplugd(eth0)[248]: Initialization complete, link beat detected.
Apr 3 19:23:00 ccu3-webui daemon.warn ifplugd(eth0)[248]: Could not open /dev/tty, cannot beep.
Apr 3 19:23:00 ccu3-webui daemon.info ifplugd(eth0)[248]: Executing '/etc/ifplugd/ifplugd.action eth0 up'.
Apr 3 19:23:00 ccu3-webui daemon.warn ifplugd(eth0)[248]: client: ifup: interface eth0 already configured
Apr 3 19:23:00 ccu3-webui daemon.info ifplugd(eth0)[248]: Program executed successfully.
Apr 3 19:23:09 ccu3-webui daemon.notice ntpdate[256]: step time server 85.220.190.246 offset -0.001092 sec
Apr 3 19:23:09 ccu3-webui daemon.notice ntpd[257]: ntpd 4.2.8p12@1.3728-o Fri Jan 31 07:49:30 UTC 2020 (1): Starting
Apr 3 19:23:09 ccu3-webui daemon.info ntpd[257]: Command line: /usr/sbin/ntpd -g 0.de.pool.ntp.org 1.de.pool.ntp.org 2.de.pool.ntp.org 3.de.pool.ntp.org
Apr 3 19:23:09 ccu3-webui daemon.info ntpd[259]: proto: precision = 0.574 usec (-21)
Apr 3 19:23:09 ccu3-webui daemon.info ntpd[259]: Listen and drop on 0 v6wildcard [::]:123
Apr 3 19:23:09 ccu3-webui daemon.info ntpd[259]: Listen and drop on 1 v4wildcard 0.0.0.0:123
Apr 3 19:23:09 ccu3-webui daemon.info ntpd[259]: Listen normally on 2 lo 127.0.0.1:123
Apr 3 19:23:09 ccu3-webui daemon.info ntpd[259]: Listen normally on 3 eth0 192.168.178.46:123
Apr 3 19:23:09 ccu3-webui daemon.info ntpd[259]: Listen normally on 4 lo [::1]:123
Apr 3 19:23:09 ccu3-webui daemon.info ntpd[259]: Listening on routing socket on fd #21 for interface updates
Apr 3 19:23:09 ccu3-webui daemon.info ntpd[259]: kernel reports TIME_ERROR: 0x2041: Clock Unsynchronized
Apr 3 19:23:09 ccu3-webui daemon.info ntpd[259]: kernel reports TIME_ERROR: 0x2041: Clock Unsynchronized
Apr 3 19:23:09 ccu3-webui daemon.err xinetd[276]: Unable to read included directory: /etc/config/xinetd.d [file=/etc/xinetd.conf] [line=14]
Apr 3 19:23:09 ccu3-webui daemon.crit xinetd[276]: 276 {init_services} no services. Exiting...
Apr 3 19:23:10 ccu3-webui user.info root: Updating RF Lan Gateway Coprocessor Firmware
Apr 3 19:23:10 ccu3-webui user.debug update-coprocessor: firmware filename is: coprocessor_update_hm_only.eq3
Apr 3 19:23:10 ccu3-webui user.info root: Updating RF Lan Gateway Firmware
Apr 3 19:23:10 ccu3-webui user.info update-lgw-firmware: No gateway found in config file /etc/config/rfd.conf
Apr 3 19:23:14 ccu3-webui user.info kernel: [ 37.440947] eq3loop: eq3loop_open_slave() mmd_bidcos
Apr 3 19:24:29 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000ED709AED46A:1","ACTUAL_TEMPERATURE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: ACTUAL_TEMPERATURE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000ED709AED46A:1","ACTUAL_TEMPERATURE"}) [CallGetValue():iseXmlRpc.cpp:1435]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0.000000 [ReadValue():iseDOMdpHSS.cpp:124]
Apr 3 19:24:29 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000ED709AED46A:1","ACTUAL_TEMPERATURE_STATUS"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: ACTUAL_TEMPERATURE_STATUS"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000ED709AED46A:1","ACTUAL_TEMPERATURE_STATUS"}) [CallGetValue():iseXmlRpc.cpp:1435]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124]
Apr 3 19:24:29 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000ED709AED46A:1","HUMIDITY"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: HUMIDITY"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000ED709AED46A:1","HUMIDITY"}) [CallGetValue():iseXmlRpc.cpp:1435]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124]
Apr 3 19:24:29 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000ED709AED46A:1","HUMIDITY_STATUS"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: HUMIDITY_STATUS"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000ED709AED46A:1","HUMIDITY_STATUS"}) [CallGetValue():iseXmlRpc.cpp:1435]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124]
Apr 3 19:24:29 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000313C9933E8C:1","SET_POINT_TEMPERATURE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: SET_POINT_TEMPERATURE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000313C9933E8C:1","SET_POINT_TEMPERATURE"}) [CallGetValue():iseXmlRpc.cpp:1435]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0.000000 [ReadValue():iseDOMdpHSS.cpp:124]
Apr 3 19:24:29 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000313C9933E8C:1","ACTUAL_TEMPERATURE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: ACTUAL_TEMPERATURE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000313C9933E8C:1","ACTUAL_TEMPERATURE"}) [CallGetValue():iseXmlRpc.cpp:1435]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0.000000 [ReadValue():iseDOMdpHSS.cpp:124]
Apr 3 19:24:29 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000313C9933E8C:1","ACTIVE_PROFILE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: ACTIVE_PROFILE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000313C9933E8C:1","ACTIVE_PROFILE"}) [CallGetValue():iseXmlRpc.cpp:1435]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124]
Apr 3 19:24:29 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000313C9933E8C:1","HUMIDITY"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: HUMIDITY"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000313C9933E8C:1","HUMIDITY"}) [CallGetValue():iseXmlRpc.cpp:1435]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124]
Apr 3 19:24:29 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000313C9933E8C:1","WINDOW_STATE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: WINDOW_STATE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000313C9933E8C:1","WINDOW_STATE"}) [CallGetValue():iseXmlRpc.cpp:1435]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124]
Apr 3 19:24:29 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000313C9933E8C:1","SET_POINT_MODE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: SET_POINT_MODE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000313C9933E8C:1","SET_POINT_MODE"}) [CallGetValue():iseXmlRpc.cpp:1435]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124]
Apr 3 19:24:29 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000313C9933E8C:1","PARTY_TIME_START"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: PARTY_TIME_START"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000313C9933E8C:1","PARTY_TIME_START"}) [CallGetValue():iseXmlRpc.cpp:1435]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = [ReadValue():iseDOMdpHSS.cpp:124]
Apr 3 19:24:29 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000313C9933E8C:1","PARTY_TIME_END"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: PARTY_TIME_END"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000313C9933E8C:1","PARTY_TIME_END"}) [CallGetValue():iseXmlRpc.cpp:1435]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = [ReadValue():iseDOMdpHSS.cpp:124]
Apr 3 19:24:29 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000313C9933E8C:1","PARTY_SET_POINT_TEMPERATURE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: PARTY_SET_POINT_TEMPERATURE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000313C9933E8C:1","PARTY_SET_POINT_TEMPERATURE"}) [CallGetValue():iseXmlRpc.cpp:1435]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0.000000 [ReadValue():iseDOMdpHSS.cpp:124]
Apr 3 19:24:29 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000313C9933E8C:1","PARTY_MODE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: PARTY_MODE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000313C9933E8C:1","PARTY_MODE"}) [CallGetValue():iseXmlRpc.cpp:1435]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124]
Apr 3 19:24:29 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000E57098F211F:1","SET_POINT_TEMPERATURE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: SET_POINT_TEMPERATURE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000E57098F211F:1","SET_POINT_TEMPERATURE"}) [CallGetValue():iseXmlRpc.cpp:1435]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0.000000 [ReadValue():iseDOMdpHSS.cpp:124]
Apr 3 19:24:29 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000E57098F211F:1","ACTUAL_TEMPERATURE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: ACTUAL_TEMPERATURE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000E57098F211F:1","ACTUAL_TEMPERATURE"}) [CallGetValue():iseXmlRpc.cpp:1435]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0.000000 [ReadValue():iseDOMdpHSS.cpp:124]
Apr 3 19:24:29 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000E57098F211F:1","ACTIVE_PROFILE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: ACTIVE_PROFILE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000E57098F211F:1","ACTIVE_PROFILE"}) [CallGetValue():iseXmlRpc.cpp:1435]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124]
Apr 3 19:24:29 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000E57098F211F:1","HUMIDITY"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: HUMIDITY"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000E57098F211F:1","HUMIDITY"}) [CallGetValue():iseXmlRpc.cpp:1435]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124]
Apr 3 19:24:29 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000E57098F211F:1","WINDOW_STATE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: WINDOW_STATE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000E57098F211F:1","WINDOW_STATE"}) [CallGetValue():iseXmlRpc.cpp:1435]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124]
Apr 3 19:24:29 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000E57098F211F:1","SET_POINT_MODE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: SET_POINT_MODE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000E57098F211F:1","SET_POINT_MODE"}) [CallGetValue():iseXmlRpc.cpp:1435]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124]
Apr 3 19:24:29 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000E57098F211F:1","PARTY_TIME_START"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: PARTY_TIME_START"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000E57098F211F:1","PARTY_TIME_START"}) [CallGetValue():iseXmlRpc.cpp:1435]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = [ReadValue():iseDOMdpHSS.cpp:124]
Apr 3 19:24:29 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000E57098F211F:1","PARTY_TIME_END"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: PARTY_TIME_END"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000E57098F211F:1","PARTY_TIME_END"}) [CallGetValue():iseXmlRpc.cpp:1435]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = [ReadValue():iseDOMdpHSS.cpp:124]
Apr 3 19:24:29 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000E57098F211F:1","PARTY_SET_POINT_TEMPERATURE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: PARTY_SET_POINT_TEMPERATURE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000E57098F211F:1","PARTY_SET_POINT_TEMPERATURE"}) [CallGetValue():iseXmlRpc.cpp:1435]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0.000000 [ReadValue():iseDOMdpHSS.cpp:124]
Apr 3 19:24:29 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"000E57098F211F:1","PARTY_MODE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: PARTY_MODE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"000E57098F211F:1","PARTY_MODE"}) [CallGetValue():iseXmlRpc.cpp:1435]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124]
Apr 3 19:24:29 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"0000D3C9960DE4:1","STATE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: STATE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"0000D3C9960DE4:1","STATE"}) [CallGetValue():iseXmlRpc.cpp:1435]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124]
Apr 3 19:24:29 ccu3-webui local0.warn ReGaHss: WARNING: XMLRPC 'getValue': rpcClient.isFault() failed (url: xmlrpc://127.0.0.1:32010, params: {"0000D709956C60:1","STATE"}, result: [faultCode:-5,faultString:"Unknown Parameter value for value key: STATE"]) [CallXmlrpcMethod():iseXmlRpc.cpp:2608]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: XMLRPC 'getValue' call failed (interface: 1009, params: {"0000D709956C60:1","STATE"}) [CallGetValue():iseXmlRpc.cpp:1435]
Apr 3 19:24:29 ccu3-webui local0.err ReGaHss: ERROR: CallGetValue failed; sVal = 0 [ReadValue():iseDOMdpHSS.cpp:124]
Code: Alles auswählen
sudo pivccu-attach cat /var/log/hmserver.log
Apr 3 19:24:09 de.eq3.lib.util.dynamics.GenericFactory INFO [main] @GenericFactory
Apr 3 19:24:09 de.eq3.lib.util.dynamics.GenericFactory INFO [main] created instance of HMServerConfiguration with parameter(s)
Apr 3 19:24:09 de.eq3.lib.util.dynamics.GenericFactory INFO [main] passed 1 parameter(s), in declarative order [String]
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [HMIPTRXWriterWorker] (1) *worker
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [KeyServerWorker] (1) *worker
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [KryoPersistenceWorker] (1) *worker
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [TransactionSubsystemHandler] (1) *worker
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [FirmwareLoaderFileSystem] (1) *worker
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [LocalServerPersistentDataLoader] (1)
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [LocalServerAdapterInitialization] (1)
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [BackendCommandHandler] (1)
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [DeviceInclusionAcceptHandler] (1)
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [CheckDeviceExistHandler] (1)
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [IncomingHMIPFrameHandler] (1)
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [DeviceBackgroundUpdateSubsystem] (1)
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [DeviceLiveUpdateSubsystem] (1)
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [DeviceInclusionDefaultConfigurationChanger] (1)
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [CyclicSmokeDetectorAwakening] (1)
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [AccessPointElectroCardioGram] (1)
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [LocalServerFirmwareUpdateInitialization] (1)
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [AccessPointAuthorisationHandler] (1)
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [AccessPointMessageDispatcher] (1)
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [AccessPointWatchdog] (1)
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [WebSocketManager] (1)
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [AccessPointCommDevice] (1)
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [RouterKeyServerWorker] (1) *worker
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [AccessPointKeyServerWorker] (1) *worker
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [RemoteCommAdapterInitialization] (1)
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [RemoteCommAdapterFinalization] (1)
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [LanRoutingWorker] (1) *worker
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [LegacyNotificationHandler] (1) *worker
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [LegacyAPIWorker] (1) *worker
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [LegacyBackendNotificationHandler] (3) *worker
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [LegacyBlindLevelCorrectionHandler] (1) *worker
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: added for deployment [LegacyInitializion] (1)
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: deploying 32 classes to Vert.x
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: 32 VertxDeployers initialized
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-4] SYSTEM: start of CyclicSmokeDetectorAwakening succeeded (cadf676c-a18d-41b6-8d98-f85c891e1f20)
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-5] SYSTEM: start of CheckDeviceExistHandler succeeded (920b5123-df68-4077-bbec-3a1d9ecb3333)
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-6] SYSTEM: start of HMIPTRXWriterWorker succeeded (1508675b-daf5-4958-8055-9b72249e5993)
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-7] SYSTEM: start of TransactionSubsystemHandler succeeded (7b2bf7cd-e836-4822-83f9-b4f75ff06831)
Apr 3 19:24:13 de.eq3.cbcs.server.core.vertx.KeyServerWorker ERROR [vert.x-worker-thread-4] Missing key server configuration parameter (Network.Key) for mode: KEYSERVER_LOCAL
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-5] SYSTEM: start of DeviceInclusionDefaultConfigurationChanger succeeded (d626ba7e-be15-49a5-86c4-6d8d8ed253ea)
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-6] SYSTEM: start of LegacyBlindLevelCorrectionHandler succeeded (bed0f638-7266-48a8-a35f-b0546cafd8cd)
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-4] SYSTEM: start of KeyServerWorker succeeded (f6a35dd1-b421-4c86-84d8-f02165eddd86)
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-0] SYSTEM: start of AccessPointElectroCardioGram succeeded (f9317cf7-5eee-4b8f-93a2-1fe583fede9c)
Apr 3 19:24:13 de.eq3.cbcs.lib.remotecommadapter.device.security.RouterKeyServerWorker ERROR [vert.x-worker-thread-0] Missing key server configuration parameter (Network.Key) for mode: KEYSERVER_LOCAL
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-6] SYSTEM: start of RouterKeyServerWorker succeeded (1c1d74c9-6f10-4b21-96a1-3ec6bebbc395)
Apr 3 19:24:13 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-2] SYSTEM: start of AccessPointKeyServerWorker succeeded (0805c2c4-6c9c-4f9d-8cdd-481cc666e4b3)
Apr 3 19:24:14 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-1] SYSTEM: start of KryoPersistenceWorker succeeded (3897776d-6f57-42cb-8bb4-49eef581f1f0)
Apr 3 19:24:14 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-4] SYSTEM: start of LocalServerPersistentDataLoader succeeded (d941db7f-664c-4485-ae7f-a2d59c2169c8)
Apr 3 19:24:14 de.eq3.cbcs.server.core.live_otau.DeviceLiveUpdateSubsystem INFO [vert.x-eventloop-thread-0] SYSTEM: DeviceLiveUpdateSubsystem started
Apr 3 19:24:14 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-6] SYSTEM: start of DeviceLiveUpdateSubsystem succeeded (962cd27c-89cc-4f32-8692-e339b4a8b1dc)
Apr 3 19:24:14 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-3] SYSTEM: start of DeviceBackgroundUpdateSubsystem succeeded (ce8bbcc5-3b31-4265-9f58-dfd504b84b39)
Apr 3 19:24:14 de.eq3.cbcs.server.core.otau.util.FirmwareLoaderFileSystem INFO [vert.x-worker-thread-0] SYSTEM: Firmware update directory is set to /etc/config/firmware
Apr 3 19:24:14 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-5] SYSTEM: start of FirmwareLoaderFileSystem succeeded (f17cbf1c-bf7d-4d02-ad24-4315b15fb5bd)
Apr 3 19:24:14 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-7] SYSTEM: start of DeviceInclusionAcceptHandler succeeded (91051fc4-fa2d-4994-b992-e3215e3b7d6f)
Apr 3 19:24:14 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-3] SYSTEM: start of IncomingHMIPFrameHandler succeeded (3952c93f-e9ae-434f-bdf1-a0077e75c983)
Apr 3 19:24:14 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-0] SYSTEM: start of RemoteCommAdapterInitialization succeeded (74e8aed3-41b7-445e-9793-6924ab4f7db1)
Apr 3 19:24:14 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-5] SYSTEM: start of AccessPointMessageDispatcher succeeded (10f2cf27-b6b9-437c-b9e3-56d9840d829d)
Apr 3 19:24:14 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-6] SYSTEM: start of WebSocketManager succeeded (793ab1c8-02c9-4b40-80af-220d1ded2d89)
Apr 3 19:24:14 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-2] SYSTEM: start of BackendCommandHandler succeeded (512b1027-84e8-4c0a-bb82-028034e446ae)
Apr 3 19:24:14 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-4] SYSTEM: start of AccessPointCommDevice succeeded (b5712f81-3b44-43a9-9e1b-c567524425c6)
Apr 3 19:24:14 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-5] SYSTEM: start of AccessPointWatchdog succeeded (8048b51c-c861-4d9d-b2e3-c95b118d65d0)
Apr 3 19:24:14 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-7] SYSTEM: start of AccessPointAuthorisationHandler succeeded (62efc334-6ec5-4406-b84b-a3010b07d089)
Apr 3 19:24:14 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-3] SYSTEM: start of LocalServerAdapterInitialization succeeded (f055856b-0bff-442c-a012-bb1a4ee5157c)
Apr 3 19:24:15 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] TRX adapter state 1: HMIP_TRX_App
Apr 3 19:24:15 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] TRX adapter application is already running or started
Apr 3 19:24:15 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] No NWK, try to set address ...
Apr 3 19:24:15 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] Try to set radio address 11775539...
Apr 3 19:24:15 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] Set max send attempts for 3014F711A061A7DA498FA505 to 3
Apr 3 19:24:15 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] Try to get application version...
Apr 3 19:24:15 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] Application version 2.8.6
Apr 3 19:24:15 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] Bootloader version 1.0.3
Apr 3 19:24:15 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] hmos version 1.20.3
Apr 3 19:24:15 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] MCU type: Si1002_8051
Apr 3 19:24:15 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] Duty Cycle: 1.0
Apr 3 19:24:15 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] set DutyCycle limit to ffffffc8
Apr 3 19:24:15 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] Set Duty Cycle Limit
Apr 3 19:24:15 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] Current Security Counter: 95960834
Apr 3 19:24:15 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] Update security counter to calculation: 95966356
Apr 3 19:24:15 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] TRX adapter has 12 link partners
Apr 3 19:24:15 de.eq3.cbcs.server.local.base.internal.HMIPTRXInitialResponseListener INFO [Thread-6] Adapter with Access Point id 3014F711A061A7DA498FA505 initialized
Apr 3 19:24:15 de.eq3.cbcs.server.local.base.internal.LocalServerAdapterInitialization INFO [Thread-6] HMIPTRXInitialResponseListener said that Adapter was initialized
Apr 3 19:24:16 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-1] SYSTEM: start of LocalServerFirmwareUpdateInitialization succeeded (97ad212e-6975-4690-9798-f1cbc328a1f2)
Apr 3 19:24:16 de.eq3.cbcs.server.core.otau.util.FirmwareLoaderFileSystem WARN [vert.x-worker-thread-0] SYSTEM: Firmware update directory in config file is no valid directory: /etc/config/firmware
Apr 3 19:24:16 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO [vert.x-eventloop-thread-2] SYSTEM: Checking all devices on all accesspoints for updates
Apr 3 19:24:16 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO [vert.x-eventloop-thread-2] SYSTEM: There are 0 APs queued with updatable devices (RF)
Apr 3 19:24:16 de.eq3.cbcs.server.core.otau.DeviceBackgroundUpdateSubsystem INFO [vert.x-eventloop-thread-2] SYSTEM: There are 0 APs queued with updatable devices (WIRED)
Apr 3 19:24:16 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-6] SYSTEM: start of RemoteCommAdapterFinalization succeeded (33b40f95-1e62-4fbc-882f-fcd82167e0f2)
Apr 3 19:24:16 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-0] SYSTEM: start of LegacyBackendNotificationHandler succeeded (e69452e1-565c-4546-998e-90d4884accb4)
Apr 3 19:24:16 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-0] SYSTEM: start of LegacyNotificationHandler succeeded (60205c54-d32f-4e97-9e3d-f6e267f1999a)
Apr 3 19:24:16 de.eq3.cbcs.lib.lanrouting.UdpServer INFO [vert.x-worker-thread-2] UDP Routing configuration: trying to bind port 43438 on eth0 0.0.0.0 -> 192.168.178.46
Apr 3 19:24:16 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-2] SYSTEM: start of LegacyAPIWorker succeeded (ec29a4b0-9b6c-4e61-8c70-a9d328d73802)
Apr 3 19:24:16 de.eq3.cbcs.lib.lanrouting.LanRoutingWorker INFO [vert.x-worker-thread-2] AP 3014F711A061A7DA498FA505: Could not initialize routing of access point, version is 2.8.6
Apr 3 19:24:16 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-2] SYSTEM: start of LanRoutingWorker succeeded (d335ce4f-92ed-4c30-9553-65cc2e4ff5f7)
Apr 3 19:24:16 de.eq3.cbcs.lib.lanrouting.UdpServer INFO [vert.x-worker-thread-0] UDP Routing established on network interface eth0 : 0.0.0.0 (192.168.178.46)
Apr 3 19:24:16 de.eq3.cbcs.lib.lanrouting.UdpServer INFO [vert.x-worker-thread-3] UDP Routing multi cast established on network interface eth0 : 192.168.178.46
Apr 3 19:24:17 de.eq3.cbcs.lib.remotecommadapter.AccessPointCommDevice INFO [vert.x-eventloop-thread-1] SYSTEM: Started Access Point WebSocket server with port 9293
Apr 3 19:24:17 de.eq3.cbcs.lib.remotecommadapter.AccessPointCommDevice INFO [vert.x-eventloop-thread-1] SYSTEM: connector open
Apr 3 19:24:17 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-6] SYSTEM: start of LegacyInitializion succeeded (f1f4ebac-a665-49a7-baf2-65b55ef428d7)
Apr 3 19:24:17 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-0] SYSTEM: initial deployment complete _____________________________________________________
Apr 3 19:24:17 de.eq3.cbcs.server.local.LocalServer INFO [Thread-0] SYSTEM: Bind XML-RPC api to port 32010
Apr 3 19:24:19 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Default MaxEventLoopExecuteTime: 2000000000
Apr 3 19:24:19 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Default BlockedThreadCheckInterval: 1000
Apr 3 19:24:19 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Default MaxWorkerExecuteTime: 60000000000
Apr 3 19:24:19 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Default EventLoopPoolSize: 8
Apr 3 19:24:19 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-1] SYSTEM: added for deployment [BackendWorker] (1) *worker
Apr 3 19:24:19 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-1] SYSTEM: added for deployment [GroupRequestWorker] (1) *worker
Apr 3 19:24:19 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-1] SYSTEM: added for deployment [DiagramRequestWorker] (1) *worker
Apr 3 19:24:19 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-1] SYSTEM: added for deployment [StorageRequestWorker] (1) *worker
Apr 3 19:24:19 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-1] SYSTEM: added for deployment [DeviceFirmwareRequestWorker] (1) *worker
Apr 3 19:24:19 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-1] SYSTEM: added for deployment [EnergyPriceRequestWorker] (1) *worker
Apr 3 19:24:19 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-1] SYSTEM: added for deployment [CouplingRequestWorker] (1) *worker
Apr 3 19:24:19 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-1] SYSTEM: added for deployment [RegaClientWorker] (1) *worker
Apr 3 19:24:19 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-1] SYSTEM: added for deployment [GroupConfigurationPersistenceFileSystem] (1) *worker
Apr 3 19:24:19 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-1] SYSTEM: added for deployment [HmIPGatewayManagementRequestWorker] (1) *worker
Apr 3 19:24:19 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-1] SYSTEM: deploying 10 classes to Vert.x
Apr 3 19:24:19 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-1] SYSTEM: 10 VertxDeployers initialized
Apr 3 19:24:19 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-5] SYSTEM: start of CouplingRequestWorker succeeded (6db255f8-d1e5-408d-954a-60e90c9742b9)
Apr 3 19:24:19 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-4] SYSTEM: start of BackendWorker succeeded (235ef3a2-4231-4d53-ae56-2792aca343aa)
Apr 3 19:24:19 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-2] SYSTEM: start of GroupConfigurationPersistenceFileSystem succeeded (2b525238-39f1-493b-b91b-9e95fa1db560)
Apr 3 19:24:19 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-1] SYSTEM: start of EnergyPriceRequestWorker succeeded (be56837e-60ed-4da8-bdcd-32311490a03d)
Apr 3 19:24:19 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-5] SYSTEM: start of RegaClientWorker succeeded (a1c4b5fe-229d-4b0e-86a4-45de72b3af80)
Apr 3 19:24:19 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-5] SYSTEM: start of StorageRequestWorker succeeded (56ca2ffb-c3f1-45d6-b788-68c43eebe7da)
Apr 3 19:24:20 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-2] SYSTEM: start of DiagramRequestWorker succeeded (bfe9986c-47d6-482f-ba4c-6dafe514ea02)
Apr 3 19:24:20 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-1] SYSTEM: start of GroupRequestWorker succeeded (d3f3928e-461a-468d-ac64-3cac1d17329d)
Apr 3 19:24:20 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-2] SYSTEM: start of DeviceFirmwareRequestWorker succeeded (38487691-031a-46a7-9fdc-05a3d18f5ca9)
Apr 3 19:24:20 de.eq3.cbcs.vertx.management.VertxManager INFO [vert.x-eventloop-thread-2] SYSTEM: start of HmIPGatewayManagementRequestWorker succeeded (8136ac61-aea1-4aac-bf0b-3ddc9aacabef)
Apr 3 19:24:20 de.eq3.cbcs.vertx.management.VertxManager INFO [Thread-1] SYSTEM: initial deployment complete _____________________________________________________
Apr 3 19:24:20 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Starting HMServer at 127.0.0.1:39292
Apr 3 19:24:20 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Read Configuration
Apr 3 19:24:20 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Create Bidcos Dispatcher
Apr 3 19:24:20 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] InitBidCosCache
Apr 3 19:24:21 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Create groupDefinitionProvider
Apr 3 19:24:21 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Create VirtualDeviceHolder
Apr 3 19:24:21 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Create VirtualDeviceHandlerRega
Apr 3 19:24:21 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Create GroupAdministrationService
Apr 3 19:24:21 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Create GroupDeviceDispatcher
Apr 3 19:24:21 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Create GroupDeviceHandler
Apr 3 19:24:21 de.eq3.ccu.groupdevice.service.GroupDeviceHandler INFO [Thread-1] @GroupDeviceHandler - initializing...
Apr 3 19:24:21 de.eq3.ccu.groupdevice.service.GroupDeviceHandler INFO [Thread-1] --> created groupDeviceDispatcher (GroupDeviceService to BidCoS (via Dispatcher))
Apr 3 19:24:21 de.eq3.ccu.groupdevice.service.GroupDeviceHandler INFO [Thread-1] --> created virtualDeviceHandler (GroupDeviceService to ReGa)
Apr 3 19:24:21 de.eq3.ccu.groupdevice.service.GroupDeviceHandler INFO [Thread-1] --> got groupDefinitionProvider
Apr 3 19:24:21 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Create BidCosGroupMemberProvider
Apr 3 19:24:21 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Init groupAdministrationService
Apr 3 19:24:21 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Init Virtual OS Device
Apr 3 19:24:21 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Init ESHLight Bridge
Apr 3 19:24:21 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Create RrdDatalogging
Apr 3 19:24:21 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Create MeasurementService
Apr 3 19:24:21 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Init MeasurementService
Apr 3 19:24:22 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Create HTTP Server
Apr 3 19:24:22 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Create BidCos context and start handler
Apr 3 19:24:22 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Create group context and start handler
Apr 3 19:24:22 de.eq3.cbcs.legacy.bidcos.rpc.LegacyServiceHandler INFO [vert.x-worker-thread-2] (un)registerCallback on LegacyServiceHandler called from url: http://127.0.0.1:39292/bidcos
Apr 3 19:24:22 de.eq3.cbcs.legacy.bidcos.rpc.LegacyServiceHandler INFO [vert.x-worker-thread-2] init finished
Apr 3 19:24:22 de.eq3.cbcs.legacy.bidcos.rpc.internal.InterfaceInitializer INFO [vert.x-worker-thread-2] Added InterfaceId: HmIP-RF_java
Apr 3 19:24:22 de.eq3.cbcs.legacy.bidcos.rpc.internal.DeviceUtil INFO [vert.x-worker-thread-2] updateDevicesForClient HmIP-RF_java -> 124 device addresses will be added
Apr 3 19:24:23 de.eq3.ccu.server.BaseHMServer INFO [Thread-1] Starting HMServer done
Apr 3 19:24:32 de.eq3.ccu.virtualdevice.service.internal.rega.VirtualDeviceHandlerRega INFO [vert.x-eventloop-thread-3] (un)registerCallback on VirtualDeviceHandlerRega called from url: xmlrpc_bin://127.0.0.1:31999
Apr 3 19:24:32 de.eq3.ccu.virtualdevice.service.internal.rega.VirtualDeviceHandlerRega INFO [vert.x-eventloop-thread-3] Added InterfaceId: 1008
Apr 3 19:24:32 de.eq3.ccu.virtualdevice.service.internal.rega.BackendWorker INFO [vert.x-worker-thread-12] Execute BackendCommand: de.eq3.ccu.virtualdevice.service.internal.rega.BackendUpdateDevicesCommand
Apr 3 19:24:34 de.eq3.cbcs.legacy.bidcos.rpc.LegacyServiceHandler INFO [vert.x-worker-thread-1] (un)registerCallback on LegacyServiceHandler called from url: http://192.168.178.45:2010
Apr 3 19:24:34 de.eq3.cbcs.legacy.bidcos.rpc.LegacyServiceHandler INFO [vert.x-worker-thread-4] init finished
Apr 3 19:24:34 de.eq3.cbcs.legacy.bidcos.rpc.internal.InterfaceInitializer INFO [vert.x-worker-thread-4] Added InterfaceId: hm-rpc.2
Apr 3 19:24:34 de.eq3.cbcs.legacy.bidcos.rpc.internal.DeviceUtil INFO [vert.x-worker-thread-4] updateDevicesForClient hm-rpc.2 -> 124 device addresses will be added
Apr 3 19:24:42 de.eq3.ccu.virtualdevice.service.internal.rega.VirtualDeviceHandlerRega INFO [vert.x-eventloop-thread-3] (un)registerCallback on VirtualDeviceHandlerRega called from url: http://192.168.178.45:9292
Apr 3 19:24:42 de.eq3.ccu.virtualdevice.service.internal.rega.VirtualDeviceHandlerRega INFO [vert.x-eventloop-thread-3] Added InterfaceId: hm-rpc.1
Apr 3 19:24:42 de.eq3.ccu.virtualdevice.service.internal.rega.BackendWorker INFO [vert.x-worker-thread-13] Execute BackendCommand: de.eq3.ccu.virtualdevice.service.internal.rega.BackendUpdateDevicesCommand
Apr 3 19:24:42 de.eq3.cbcs.legacy.bidcos.rpc.LegacyServiceHandler INFO [vert.x-worker-thread-2] (un)registerCallback on LegacyServiceHandler called from url: xmlrpc_bin://127.0.0.1:31999
Apr 3 19:24:42 de.eq3.cbcs.legacy.bidcos.rpc.LegacyServiceHandler INFO [vert.x-worker-thread-3] init finished
Apr 3 19:24:42 de.eq3.cbcs.legacy.bidcos.rpc.internal.InterfaceInitializer INFO [vert.x-worker-thread-1] Added InterfaceId: 1009Liebe Grüße und bleibt Gesund.