ich habe im Forum nach einem neuen Funkmodul gesucht und mir wurde ein Stick HB-MOD-UART-USB angeboten. Dieser soll IP und klassisch können und ich wollte mein RPI-RF-MOD ablösen.
Nun habe ich also erst mal ein Update durchgeführt, Neustart, Heruntergefahren, das alte Modul abgezogen, den neuen Stick mal angeschlossen und via sudo dpkg-reconfigure pivccu3 die Modulauswahl aufgerufen. Zur Auswahl stehen:
1) HM-MOD-RPI-PCB / RPI-RF-MOD
2) HmIP-RFUSB (nur HmIP)
3) Software
Der Stick dürfte mittlere Option sein, dem Text nach wars dann aber mit meinen klassischen Komponenten. Das war nicht mein Ziel. Laut Git sollte aber beides gehen:
"HB-RF-USB (HmRF+HmIP, piVCCU3 only)"
Bei Auswahl 1 startet die pivccu nicht mehr und liefert nur:
pi@raspberrypi:~ $ sudo pivccu-info
piVCCU version: 3.53.34-51
Kernel modules: Available
Raw UART dev: Available
Rasp.Pi UART: Assigned to GPIO pins
HMRF Hardware: unknown
Board serial: unknown
Radio MAC: unknown
HMIP Hardware: unknown
SGTIN: unknown
Radio MAC: unknown
State: STOPPED
Bei mittlerer Auswahl bekomme ich allerdings auch nur:
pi@raspberrypi:~ $ sudo pivccu-info
piVCCU version: 3.53.34-51
Kernel modules: Available
Raw UART dev: Available
Rasp.Pi UART: Assigned to GPIO pins
find: ‘/proc/9602’: Datei oder Verzeichnis nicht gefunden
find: ‘/proc/9603’: Datei oder Verzeichnis nicht gefunden
find: ‘/proc/9608’: Datei oder Verzeichnis nicht gefunden
find: ‘/proc/9609’: Datei oder Verzeichnis nicht gefunden
find: ‘/proc/11609’: Datei oder Verzeichnis nicht gefunden
find: ‘/proc/18510’: Datei oder Verzeichnis nicht gefunden
find: ‘/proc/18511’: Datei oder Verzeichnis nicht gefunden
find: ‘/proc/18513’: Datei oder Verzeichnis nicht gefunden
find: ‘/proc/20152’: Datei oder Verzeichnis nicht gefunden
find: ‘/proc/20153’: Datei oder Verzeichnis nicht gefunden
find: ‘/proc/20154’: Datei oder Verzeichnis nicht gefunden
HMRF Hardware: FAKE_HMRF
Board serial: FKE8508344
Radio MAC: 0xffd805
HMIP Hardware: unknown
SGTIN: 3014F711A061A7D5699DAB52
Radio MAC: 0xffd805
State: STOPPED
In beiden Fällen startet die pivccu nicht mehr.
Aus lauter Verzweiflung habe ich, keine Ahnung warum, erneut ein Update angestoßen und siehe da, es finden sich sogar zwei Module:
Die folgenden Pakete werden aktualisiert (Upgrade):
pivccu-modules-dkms pivccu-modules-raspberrypi
Während der Installation kam es dann leider zu einem Haufen von Fehlern...
Code: Alles auswählen
Die folgenden Pakete werden aktualisiert (Upgrade):
pivccu-modules-dkms pivccu-modules-raspberrypi
2 aktualisiert, 0 neu installiert, 0 zu entfernen und 0 nicht aktualisiert.
Es müssen 37,7 kB an Archiven heruntergeladen werden.
Nach dieser Operation werden 0 B Plattenplatz zusätzlich benutzt.
Möchten Sie fortfahren? [J/n]
Holen:1 https://www.pivccu.de/piVCCU stable/main armhf pivccu-modules-dkms all 1.0.56 [34,9 kB]
Holen:2 https://www.pivccu.de/piVCCU stable/main armhf pivccu-modules-raspberrypi all 2.0-14 [2.832 B]
Es wurden 37,7 kB in 0 s geholt (96,1 kB/s).
Changelogs werden gelesen... Fertig
Vorkonfiguration der Pakete ...
(Lese Datenbank ... 113895 Dateien und Verzeichnisse sind derzeit installiert.)
Vorbereitung zum Entpacken von .../pivccu-modules-dkms_1.0.56_all.deb ...
Removed /etc/systemd/system/debmatic.service.wants/pivccu-dkms.service.
Removed /etc/systemd/system/pivccu.service.requires/pivccu-dkms.service.
Removed /etc/systemd/system/multi-user.target.wants/pivccu-dkms.service.
-------- Uninstall Beginning --------
Module: pivccu
Version: 1.0.54
Kernel: 5.4.83+ (armv7l)
-------------------------------------
Status: Before uninstall, this module version was ACTIVE on this kernel.
dummy_rx8130.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
dw_apb_raw_uart.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
eq3_char_loop.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
fake_hmrf.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
generic_raw_uart.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
hb_rf_eth.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
hb_rf_usb-2.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
hb_rf_usb.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
led_trigger_timer.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
meson_raw_uart.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
pl011_raw_uart.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
plat_eq3ccu2.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
rpi_rf_mod_led.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
rtc-rx8130.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83+/kernel/drivers/pivccu/
rmdir: konnte Verzeichnis 'kernel/drivers' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
Fortschritt: [ 0%] [.......................................................]
Fortschri.t: [ 0%] [.......................................................]
DKMS: uninstall completed.
-------- Uninstall Beginning --------
Module: pivccu
Version: 1.0.54
Kernel: 5.4.83-v7+ (armv7l)
-------------------------------------
Status: Before uninstall, this module version was ACTIVE on this kernel.
dummy_rx8130.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83-v7+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
dw_apb_raw_uart.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83-v7+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
eq3_char_loop.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83-v7+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
fake_hmrf.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83-v7+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
generic_raw_uart.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83-v7+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
hb_rf_eth.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83-v7+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
hb_rf_usb-2.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83-v7+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
hb_rf_usb.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83-v7+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
led_trigger_timer.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83-v7+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
meson_raw_uart.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83-v7+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
pl011_raw_uart.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83-v7+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
plat_eq3ccu2.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83-v7+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
rpi_rf_mod_led.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83-v7+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
rtc-rx8130.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83-v7+/kernel/drivers/pivccu/
rmdir: konnte Verzeichnis 'kernel/drivers' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
depmod....
DKMS: uninstall completed.
-------- Uninstall Beginning --------
Module: pivccu
Version: 1.0.54
Kernel: 5.4.83-v7l+ (armv7l)
-------------------------------------
Status: Before uninstall, this module version was ACTIVE on this kernel.
dummy_rx8130.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83-v7l+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
dw_apb_raw_uart.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83-v7l+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
eq3_char_loop.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83-v7l+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
fake_hmrf.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83-v7l+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
generic_raw_uart.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83-v7l+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
hb_rf_eth.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83-v7l+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
hb_rf_usb-2.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83-v7l+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
hb_rf_usb.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83-v7l+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
led_trigger_timer.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83-v7l+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
meson_raw_uart.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83-v7l+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
pl011_raw_uart.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83-v7l+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
plat_eq3ccu2.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83-v7l+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
rpi_rf_mod_led.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83-v7l+/kernel/drivers/pivccu/
rmdir: konnte 'kernel/drivers/pivccu' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
rtc-rx8130.ko:
- Uninstallation
- Deleting from: /lib/modules/5.4.83-v7l+/kernel/drivers/pivccu/
rmdir: konnte Verzeichnis 'kernel/drivers' nicht entfernen: Das Verzeichnis ist nicht leer
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
depmod....
DKMS: uninstall completed.
------------------------------
Deleting module version: 1.0.54
completely from the DKMS tree.
------------------------------
Done.
Entpacken von pivccu-modules-dkms (1.0.56) über (1.0.54) ...
Vorbereitung zum Entpacken von .../pivccu-modules-raspberrypi_2.0-14_all.deb ...
Removed /etc/systemd/system/multi-user.target.wants/pivccu-rpi-modules.service.
dpkg-divert: Warnung: Bitte geben Sie »--no-rename« explizit an, die Vorgabe wird in 1.20.x
auf »--rename« geändert werden
»Umleitung von /var/lib/piVCCU/dtb/overlays/pivccu-raspberrypi.dtbo zu /usr/share/rpikernelhack/overlays/pivccu-raspberrypi.dtbo durch rpikernelhack« wird hinzugefügt
Entpacken von pivccu-modules-raspberrypi (2.0-14) über (2.0-13) ...
pivccu-modules-dkms (1.0.56) wird eingerichtet ...
Creating symlink /var/lib/dkms/pivccu/1.0.56/source ->
/usr/src/pivccu-1.0.56
DKMS: add completed.
Kernel preparation unnecessary for this kernel. Skipping...
Building module:
cleaning build area.....
make -j4 KERNELRELEASE=5.4.83-v7+ ARCH=arm all..............
cleaning build area....
DKMS: build completed.
dummy_rx8130.ko:
Running module version sanity check.
- Original module
- No original module exists within this kernel
- Installation
- Installing to /lib/modules/5.4.83-v7+/kernel/drivers/pivccu/
dw_apb_raw_uart.ko:
Running module version sanity check.
- Original module
- No original module exists within this kernel
- Installation
- Installing to /lib/modules/5.4.83-v7+/kernel/drivers/pivccu/
eq3_char_loop.ko:
Running module version sanity check.
- Original module
- No original module exists within this kernel
- Installation
- Installing to /lib/modules/5.4.83-v7+/kernel/drivers/pivccu/
fake_hmrf.ko:
Running module version sanity check.
- Original module
- No original module exists within this kernel
- Installation
- Installing to /lib/modules/5.4.83-v7+/kernel/drivers/pivccu/
generic_raw_uart.ko:
Running module version sanity check.
- Original module
- No original module exists within this kernel
- Installation
- Installing to /lib/modules/5.4.83-v7+/kernel/drivers/pivccu/
hb_rf_eth.ko:
Running module version sanity check.
- Original module
- No original module exists within this kernel
- Installation
- Installing to /lib/modules/5.4.83-v7+/kernel/drivers/pivccu/
hb_rf_usb-2.ko:
Running module version sanity check.
- Original module
- No original module exists within this kernel
- Installation
- Installing to /lib/modules/5.4.83-v7+/kernel/drivers/pivccu/
hb_rf_usb.ko:
Running module version sanity check.
- Original module
- No original module exists within this kernel
- Installation
- Installing to /lib/modules/5.4.83-v7+/kernel/drivers/pivccu/
led_trigger_timer.ko:
Running module version sanity check.
- Original module
- No original module exists within this kernel
- Installation
- Installing to /lib/modules/5.4.83-v7+/kernel/drivers/pivccu/
meson_raw_uart.ko:
Running module version sanity check.
- Original module
- No original module exists within this kernel
- Installation
- Installing to /lib/modules/5.4.83-v7+/kernel/drivers/pivccu/
pl011_raw_uart.ko:
Running module version sanity check.
- Original module
- No original module exists within this kernel
- Installation
- Installing to /lib/modules/5.4.83-v7+/kernel/drivers/pivccu/
plat_eq3ccu2.ko:
Running module version sanity check.
- Original module
- No original module exists within this kernel
- Installation
- Installing to /lib/modules/5.4.83-v7+/kernel/drivers/pivccu/
rpi_rf_mod_led.ko:
Running module version sanity check.
- Original module
- No original module exists within this kernel
- Installation
- Installing to /lib/modules/5.4.83-v7+/kernel/drivers/pivccu/
rtc-rx8130.ko:
Running module version sanity check.
- Original module
- No original module exists within this kernel
- Installation
- Installing to /lib/modules/5.4.83-v7+/kernel/drivers/pivccu/
depmod...
DKMS: install completed.
Created symlink /etc/systemd/system/multi-user.target.wants/pivccu-dkms.service → /lib/systemd/system/pivccu-dkms.service.
Created symlink /etc/systemd/system/debmatic.service.wants/pivccu-dkms.service → /lib/systemd/system/pivccu-dkms.service.
Created symlink /etc/systemd/system/pivccu.service.requires/pivccu-dkms.service → /lib/systemd/system/pivccu-dkms.service.
pivccu-modules-raspberrypi (2.0-14) wird eingerichtet ...
»Umleitung von /var/lib/piVCCU/dtb/overlays/pivccu-raspberrypi.dtbo zu /usr/share/rpikernelhack/overlays/pivccu-raspberrypi.dtbo durch rpikernelhack« wird entfernt
Created symlink /etc/systemd/system/multi-user.target.wants/pivccu-rpi-modules.service → /lib/systemd/system/pivccu-rpi-modules.service.
pi@raspberrypi:~ $ sudo reboot
Etwas schräg finde ich die dmesg Ausgabe:
Code: Alles auswählen
pi@raspberrypi:~ $ dmesg
[ 200.619256] usb 1-1.1.2: Product: HB-RF-USB
[ 200.619270] usb 1-1.1.2: Manufacturer: Alexander Reinert
[ 200.619283] usb 1-1.1.2: SerialNumber: A94JS2PO
[ 200.621351] usb 1-1.1.2: Found HB-RF-USB at usb-3f980000.usb-1.1.2
[ 200.692719] usb 1-1.1.2: USB disconnect, device number 127
[ 200.693868] usb 1-1.1.2: bitmode request failed for value 0x00f0: -19
[ 200.991308] usb 1-1.1.2: new full-speed USB device number 4 using dwc_otg
[ 201.150344] usb 1-1.1.2: New USB device found, idVendor=0403, idProduct=6f70, bcdDevice= 6.00
[ 201.150366] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 201.150380] usb 1-1.1.2: Product: HB-RF-USB
[ 201.150394] usb 1-1.1.2: Manufacturer: Alexander Reinert
[ 201.150408] usb 1-1.1.2: SerialNumber: A94JS2PO
[ 201.152415] usb 1-1.1.2: Found HB-RF-USB at usb-3f980000.usb-1.1.2
[ 201.222837] usb 1-1.1.2: USB disconnect, device number 4
[ 201.223762] usb 1-1.1.2: bitmode request failed for value 0x00f0: -19
[ 201.541376] usb 1-1.1.2: new full-speed USB device number 7 using dwc_otg
[ 201.699217] usb 1-1.1.2: New USB device found, idVendor=0403, idProduct=6f70, bcdDevice= 6.00
[ 201.699239] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 201.699254] usb 1-1.1.2: Product: HB-RF-USB
[ 201.699268] usb 1-1.1.2: Manufacturer: Alexander Reinert
[ 201.699281] usb 1-1.1.2: SerialNumber: A94JS2PO
[ 201.701382] usb 1-1.1.2: Found HB-RF-USB at usb-3f980000.usb-1.1.2
[ 201.772711] usb 1-1.1.2: USB disconnect, device number 7
[ 201.773737] usb 1-1.1.2: bitmode request failed for value 0x00f0: -19
[ 202.071264] usb 1-1.1.2: new full-speed USB device number 8 using dwc_otg
[ 202.230172] usb 1-1.1.2: New USB device found, idVendor=0403, idProduct=6f70, bcdDevice= 6.00
[ 202.230181] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 202.230188] usb 1-1.1.2: Product: HB-RF-USB
[ 202.230194] usb 1-1.1.2: Manufacturer: Alexander Reinert
[ 202.230199] usb 1-1.1.2: SerialNumber: A94JS2PO
[ 202.231665] usb 1-1.1.2: Found HB-RF-USB at usb-3f980000.usb-1.1.2
[ 202.302719] usb 1-1.1.2: USB disconnect, device number 8
[ 202.303667] usb 1-1.1.2: bitmode request failed for value 0x00f0: -19
Wie hätte ich vorgehen sollen?
Was kann ich jetzt machen? ...und... lohnt es sich überhaupt? Ohne HM klassisch wäre die pivccu3 und der STick für mich eh sinnfrei
Grüße
Manuel