Update auf Bullseye 64 Bit
Verfasst: 19.08.2022, 19:38
Hallo zusammen,
heute habe ich es mal gewagt und habe meinen Raspberry Pi 4 - 8 GB von Buster 32 Bit auf Bullseye mit 64 Bit aktualisiert.
Allerdings mit dem Ergebnis, daß piVCCU leider nicht mehr nicht mehr startet.
Den Raspi-Kernel habe ich auch aktualisiert und auch 10 Minuten abgewartet.
Auch sudo dpkg-reconfigure pivccu-modules-dkms mal durchlaufen lassen. Leider ohne Erfolg.
Was mich etwas etwas erstaunt ist der Fehler "Could not load required kernel module eq3_char_loop." Habe aber keine Idee wie ich den Char_Loop nachschieben kann.
Noch ein Nachtrag von sudo dpkg-reconfigure pivccu-modules-dkms
Ein Backup ist da, daher habe ich mal auf die große Hupe gedrückt und alles hochgefahren.
Unter 32 Bit geht alles wunderbar.
Wäre klasse wenn jemand eine Idee hat wie man alles auf 64 Bit laufen lassen kann.
Grüße vom
Mark
heute habe ich es mal gewagt und habe meinen Raspberry Pi 4 - 8 GB von Buster 32 Bit auf Bullseye mit 64 Bit aktualisiert.
Allerdings mit dem Ergebnis, daß piVCCU leider nicht mehr nicht mehr startet.
Den Raspi-Kernel habe ich auch aktualisiert und auch 10 Minuten abgewartet.
Code: Alles auswählen
pi@raspberrypi:~ $ sudo pivccu-info
piVCCU version: 3.65.6-73
Kernel modules: Not available
Raw UART dev: Not available
Rasp.Pi UART: Assigned to GPIO pins
HMRF Hardware: unknown
HMIP Hardware: unknown
State: STOPPED
Code: Alles auswählen
pi@raspberrypi:~ $ sudo systemctl status pivccu.service
● pivccu.service - piVCCU
Loaded: loaded (/lib/systemd/system/pivccu.service; enabled; vendor preset: enabled)
Active: failed (Result: protocol) since Fri 2022-08-19 19:07:45 CEST; 16min ago
Process: 984 ExecStart=/var/lib/piVCCU3/start_container.sh (code=exited, status=0/SUCCESS)
CPU: 34ms
Aug 19 19:07:45 raspberrypi systemd[1]: Starting piVCCU...
Aug 19 19:07:45 raspberrypi start_container.sh[987]: modprobe: FATAL: Module eq3_char_loop not found in directory /lib/modules/5.15.56-v8+
Aug 19 19:07:45 raspberrypi systemd[1]: pivccu.service: Can't open PID file /run/pivccu3.pid (yet?) after start: Operation not permitted
Aug 19 19:07:45 raspberrypi systemd[1]: pivccu.service: Failed with result 'protocol'.
Aug 19 19:07:45 raspberrypi systemd[1]: Failed to start piVCCU.
Code: Alles auswählen
pi@raspberrypi:~ $ systemctl start pivccu
==== AUTHENTICATING FOR org.freedesktop.systemd1.manage-units ===
Legitimierung ist zum Starten von »pivccu.service« notwendig.
Authenticating as: ,,, (pi)
Password:
==== AUTHENTICATION COMPLETE ===
Job for pivccu.service failed because the service did not take the steps required by its unit configuration.
See "systemctl status pivccu.service" and "journalctl -xe" for details.
pi@raspberrypi:~ $
Auch sudo dpkg-reconfigure pivccu-modules-dkms mal durchlaufen lassen. Leider ohne Erfolg.
Was mich etwas etwas erstaunt ist der Fehler "Could not load required kernel module eq3_char_loop." Habe aber keine Idee wie ich den Char_Loop nachschieben kann.
Code: Alles auswählen
pi@raspberrypi:/lib/modules $ ls
5.15.56+ 5.15.56-v7+ 5.15.56-v7l+ 5.15.56-v8+
pi@raspberrypi:/lib/modules $ cd 5.15.56-v8+/
pi@raspberrypi:/lib/modules/5.15.56-v8+ $ ls
kernel modules.alias modules.alias.bin modules.builtin modules.builtin.alias.bin modules.builtin.bin modules.builtin.modinfo modules.dep modules.dep.bin modules.devname modules.order modules.softdep modules.symbols modules.symbols.bin
pi@raspberrypi:/lib/modules/5.15.56-v8+ $
Code: Alles auswählen
pi@raspberrypi:/lib/modules/5.15.56-v7l+ $ sudo dpkg-reconfigure pivccu-modules-dkms
Removed /etc/systemd/system/debmatic.service.wants/pivccu-dkms.service.
Removed /etc/systemd/system/pivccu.service.requires/pivccu-dkms.service.
Removed /etc/systemd/system/multi-user.target.wants/pivccu-dkms.service.
------------------------------
Deleting module version: 1.0.77
completely from the DKMS tree.
------------------------------
Done.
Error! The module/version combo: pivccu-1.0.77
is not located in the DKMS tree.
Creating symlink /var/lib/dkms/pivccu/1.0.77/source ->
/usr/src/pivccu-1.0.77
DKMS: add completed.
Error! echo
Your kernel headers for kernel 5.15.56-v8+ cannot be found at
/lib/modules/5.15.56-v8+/build or /lib/modules/5.15.56-v8+/source.
You can use the --kernelsourcedir option to tell DKMS where it's located.
Created symlink /etc/systemd/system/multi-user.target.wants/pivccu-dkms.service → /lib/systemd/system/pivccu-dkms.service.
Created symlink /etc/systemd/system/debmatic.service.wants/pivccu-dkms.service → /lib/systemd/system/pivccu-dkms.service.
Created symlink /etc/systemd/system/pivccu.service.requires/pivccu-dkms.service → /lib/systemd/system/pivccu-dkms.service.
pi@raspberrypi:/lib/modules/5.15.56-v7l+ $ sudo dpkg-reconfigure pivccu-modules-dkms
Removed /etc/systemd/system/debmatic.service.wants/pivccu-dkms.service.
Removed /etc/systemd/system/pivccu.service.requires/pivccu-dkms.service.
Removed /etc/systemd/system/multi-user.target.wants/pivccu-dkms.service.
------------------------------
Deleting module version: 1.0.77
completely from the DKMS tree.
------------------------------
Done.
Error! The module/version combo: pivccu-1.0.77
is not located in the DKMS tree.
Creating symlink /var/lib/dkms/pivccu/1.0.77/source ->
/usr/src/pivccu-1.0.77
DKMS: add completed.
Error! echo
Your kernel headers for kernel 5.15.56-v8+ cannot be found at
/lib/modules/5.15.56-v8+/build or /lib/modules/5.15.56-v8+/source.
You can use the --kernelsourcedir option to tell DKMS where it's located.
Created symlink /etc/systemd/system/multi-user.target.wants/pivccu-dkms.service → /lib/systemd/system/pivccu-dkms.service.
Created symlink /etc/systemd/system/debmatic.service.wants/pivccu-dkms.service → /lib/systemd/system/pivccu-dkms.service.
Created symlink /etc/systemd/system/pivccu.service.requires/pivccu-dkms.service → /lib/systemd/system/pivccu-dkms.service.
pi@raspberrypi:/lib/modules/5.15.56-v7l+ $
Unter 32 Bit geht alles wunderbar.
Wäre klasse wenn jemand eine Idee hat wie man alles auf 64 Bit laufen lassen kann.
Grüße vom
Mark