Re: Drucksensor HB-UNI-Sen-PRESS(-SC)
Verfasst: 12.07.2018, 21:22
erwischt
Heimautomation mit ELV HomeMatic und FHZ Funk-Hauszentralen
https://homematic-forum.de/forum/
Code: Alles auswählen
Arduino: 1.8.5 (Windows 10), Board: "Arduino/Genuino Uno"
C:\Users\\Documents\Arduino\libraries\EnableInterrupt/EnableInterrupt.h:22:125: note: #pragma message: NOTICE: *** EnableInterrupt library version pre-0.9.6. This is not a problem. Keep calm, and carry on. ***
#pragma message("NOTICE: *** EnableInterrupt library version pre-0.9.6. This is not a problem. Keep calm, and carry on. ***")
^
Der Sketch verwendet 24454 Bytes (75%) des Programmspeicherplatzes. Das Maximum sind 32256 Bytes.
Globale Variablen verwenden 986 Bytes (48%) des dynamischen Speichers, 1062 Bytes für lokale Variablen verbleiben. Das Maximum sind 2048 Bytes.
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x46
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x46
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x46
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x46
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x46
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x46
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x46
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x46
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x46
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x46
Problem beim Hochladen auf das Board. Hilfestellung dazu unter http://www.arduino.cc/en/Guide/Troubleshooting#upload.
Code: Alles auswählen
avrdude: Version 6.3, compiled on Jan 17 2017 at 12:00:53
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch
System wide configuration file is "C:\Users\Fredi\AppData\Local\Arduino15\packages\arduino\tools\avrdude\6.3.0-arduino9/etc/avrdude.conf"
Using Port : COM12
Using Programmer : arduino
Overriding Baud Rate : 115200
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x87
Hallo Jérôme,jp112sdl hat geschrieben: ↑07.07.2018, 11:41Habs mal testweise quick&dirty mit reinkompiliert.
Passt ganz knapp noch... aber auch nur bei dem ohne SC.
Liegt in nem extra Branch: https://github.com/jp112sdl/HB-UNI-Sen- ... ev_ssd1306
Hallo Martin,Nitram101 hat geschrieben: ↑24.07.2018, 19:12Hallo Jérôme,jp112sdl hat geschrieben: ↑07.07.2018, 11:41Habs mal testweise quick&dirty mit reinkompiliert.
Passt ganz knapp noch... aber auch nur bei dem ohne SC.
Liegt in nem extra Branch: https://github.com/jp112sdl/HB-UNI-Sen- ... ev_ssd1306
vielen Dank für deine Mühe und Eifer "an dieser Stelle ziehe ich mal meinen Hut für Dich".
Allem Testen zum Trotze habe ich es leider nicht hinbekommen dem Display eine Anzeige zu entlocken!
Testprogramme laufen alle mit der Verdrahtung, nur finde ich den Fehler nicht in dem Sketch,
Adrssen stimmen, usw. ich binn so langsam am verweifeln.
Vieleicht würdest Du oder eine anderer die die Idee weiter aufgreift noch eimal drüberschauen.
Martin
Code: Alles auswählen
...
if (number() == 6) displayLine6 = vStr;
printDisplay();