Neue Platine HB-RF-USB-2

Entwicklung und Bau von Hardware aller Art, die im HM-Umfeld eingesetzt werden kann

Moderator: Co-Administratoren

deimos
Beiträge: 4574
Registriert: 20.06.2017, 10:38
Wohnort: Leimersheim
Hat sich bedankt: 88 Mal
Danksagung erhalten: 586 Mal
Kontaktdaten:

Re: Neue Platine HB-RF-USB-2

Beitrag von deimos » 30.07.2021, 11:22

Hi,

Code: Alles auswählen

sudo apt update
sudo apt upgrade
Dann Reboot, dann Anleitung befolgen.

Viele Grüße
Alex

torbar
Beiträge: 13
Registriert: 29.07.2021, 19:53
System: Alternative CCU (auf Basis OCCU)

Re: Neue Platine HB-RF-USB-2

Beitrag von torbar » 30.07.2021, 14:38

Die Debmatic installation ist soweit ohne Fehler durchgelaufen.

Ich kann mich an der Weboberflaechse anmelden, sehe haber keine Zentrale.
Das RPi-RF-MOD leuchtet gruen.

Ich denke ich sollte zumindest einmal die CCU sehen, oder ?

Torsten


torbar
Beiträge: 13
Registriert: 29.07.2021, 19:53
System: Alternative CCU (auf Basis OCCU)

Re: Neue Platine HB-RF-USB-2

Beitrag von torbar » 30.07.2021, 14:58

Hi,

hier die Ergenisse:

pi@raspberrypi:~ $ sudo debmatic-info
debmatic version: 3.59.6-73
Kernel modules: Not available
Raw UART dev: Not available
HMRF Hardware: unknown
Board serial: unknown
Radio MAC: unknown
HMIP Hardware: unknown
SGTIN: unknown
Radio MAC: unknown

pi@raspberrypi:~ $ sudo lsusb
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 004: ID 10c4:8c07 Cygnal Integrated Products, Inc.
Bus 001 Device 002: ID 2109:3431 VIA Labs, Inc. Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub


pi@raspberrypi:~ $ dmesg
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.10.52-v7l+ (dom@buildbot) (arm-linux-gnueabihf-gcc-8 (Ubuntu/Linaro 8.4.0-3ubuntu1) 8.4.0, GNU ld (GNU Binutils for Ubuntu) 2.34) #1440 SMP Tue Jul 27 09:55:21 BST 2021
[ 0.000000] CPU: ARMv7 Processor [410fd083] revision 3 (ARMv7), cr=30c5383d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] OF: fdt: Machine model: Raspberry Pi 4 Model B Rev 1.2
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] Reserved memory: created CMA memory pool at 0x000000000ec00000, size 512 MiB
[ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000000000-0x000000002fffffff]
[ 0.000000] Normal empty
[ 0.000000] HighMem [mem 0x0000000030000000-0x00000000fbffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000003b3fffff]
[ 0.000000] node 0: [mem 0x0000000040000000-0x00000000fbffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000000fbffffff]
[ 0.000000] On node 0 totalpages: 1012736
[ 0.000000] DMA zone: 1728 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 196608 pages, LIFO batch:63
[ 0.000000] HighMem zone: 816128 pages, LIFO batch:63
[ 0.000000] percpu: Embedded 20 pages/cpu s50764 r8192 d22964 u81920
[ 0.000000] pcpu-alloc: s50764 r8192 d22964 u81920 alloc=20*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1011008
[ 0.000000] Kernel command line: coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 smsc95xx.macaddr=DC:A6:32:FB:71:0D vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000 console=ttyAMA0,115200 console=tty1 root=PARTUUID=e0f7eb03-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait quiet splash plymouth.ignore-serial-consoles
[ 0.000000] Kernel parameter elevator= does not have any effect anymore.
Please use sysfs to set IO scheduler for individual devices.
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] software IO TLB: mapped [mem 0x0000000008890000-0x000000000c890000] (64MB)
[ 0.000000] Memory: 3404140K/4050944K available (10240K kernel code, 1364K rwdata, 3188K rodata, 2048K init, 891K bss, 122516K reserved, 524288K cma-reserved, 3264512K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] ftrace: allocating 34303 entries in 67 pages
[ 0.000000] ftrace: allocated 67 pages with 3 groups
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Rude variant of Tasks RCU enabled.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] random: get_random_bytes called from start_kernel+0x3c8/0x59c with crng_init=0
[ 0.000008] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns
[ 0.000027] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns
[ 0.000087] bcm2835: system timer (irq = 25)
[ 0.000735] arch_timer: cp15 timer(s) running at 54.00MHz (phys).
[ 0.000753] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xc743ce346, max_idle_ns: 440795203123 ns
[ 0.000771] sched_clock: 56 bits at 54MHz, resolution 18ns, wraps every 4398046511102ns
[ 0.000785] Switching to timer-based delay loop, resolution 18ns
[ 0.001043] Console: colour dummy device 80x30
[ 0.001113] printk: console [tty1] enabled
[ 0.001168] Calibrating delay loop (skipped), value calculated using timer frequency.. 108.00 BogoMIPS (lpj=540000)
[ 0.001202] pid_max: default: 32768 minimum: 301
[ 0.001364] LSM: Security Framework initializing
[ 0.001553] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.001579] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.003019] cgroup: Disabling memory control group subsystem
[ 0.003251] CPU: Testing write buffer coherency: ok
[ 0.003715] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.004949] Setting up static identity map for 0x200000 - 0x20003c
[ 0.005150] rcu: Hierarchical SRCU implementation.
[ 0.006090] smp: Bringing up secondary CPUs ...
[ 0.007297] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.008662] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.009963] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.010120] smp: Brought up 1 node, 4 CPUs
[ 0.010141] SMP: Total of 4 processors activated (432.00 BogoMIPS).
[ 0.010156] CPU: All CPU(s) started in HYP mode.
[ 0.010170] CPU: Virtualization extensions available.
[ 0.011112] devtmpfs: initialized
[ 0.025465] VFP support v0.3: implementor 41 architecture 3 part 40 variant 8 rev 0
[ 0.025694] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.025724] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.038264] pinctrl core: initialized pinctrl subsystem
[ 0.039338] NET: Registered protocol family 16
[ 0.043401] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[ 0.044174] audit: initializing netlink subsys (disabled)
[ 0.044438] audit: type=2000 audit(0.040:1): state=initialized audit_enabled=0 res=1
[ 0.045016] thermal_sys: Registered thermal governor 'step_wise'
[ 0.045796] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.045814] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.046213] Serial: AMBA PL011 UART driver
[ 0.078284] bcm2835-mbox fe00b880.mailbox: mailbox enabled
[ 0.090850] raspberrypi-firmware soc:firmware: Attached to firmware from 2021-07-21T16:21:46, variant start
[ 0.100863] raspberrypi-firmware soc:firmware: Firmware hash is 6a796bb0062a6c75191c57cba1c13f9300076d02
[ 0.141833] Kprobes globally optimized
[ 0.146923] bcm2835-dma fe007000.dma: DMA legacy API manager, dmachans=0x1
[ 0.151138] vgaarb: loaded
[ 0.151592] SCSI subsystem initialized
[ 0.151809] usbcore: registered new interface driver usbfs
[ 0.151882] usbcore: registered new interface driver hub
[ 0.151956] usbcore: registered new device driver usb
[ 0.152292] usb_phy_generic phy: supply vcc not found, using dummy regulator
[ 0.154269] clocksource: Switched to clocksource arch_sys_counter
[ 1.112976] VFS: Disk quotas dquot_6.6.0
[ 1.113069] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.113228] FS-Cache: Loaded
[ 1.113446] CacheFiles: Loaded
[ 1.124352] NET: Registered protocol family 2
[ 1.124596] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 1.126052] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 1.126093] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 1.126158] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 1.126230] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.126391] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 1.126426] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 1.126693] NET: Registered protocol family 1
[ 1.127455] RPC: Registered named UNIX socket transport module.
[ 1.127472] RPC: Registered udp transport module.
[ 1.127487] RPC: Registered tcp transport module.
[ 1.127502] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.127525] PCI: CLS 0 bytes, default 64
[ 1.130516] Initialise system trusted keyrings
[ 1.130760] workingset: timestamp_bits=14 max_order=20 bucket_order=6
[ 1.139305] zbud: loaded
[ 1.141438] FS-Cache: Netfs 'nfs' registered for caching
[ 1.142227] NFS: Registering the id_resolver key type
[ 1.142267] Key type id_resolver registered
[ 1.142282] Key type id_legacy registered
[ 1.142428] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.142445] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 1.143490] Key type asymmetric registered
[ 1.143507] Asymmetric key parser 'x509' registered
[ 1.143701] bounce: pool size: 64 pages
[ 1.143746] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 1.143957] io scheduler mq-deadline registered
[ 1.143974] io scheduler kyber registered
[ 1.148461] brcm-pcie fd500000.pcie: host bridge /scb/pcie@7d500000 ranges:
[ 1.148493] brcm-pcie fd500000.pcie: No bus range found for /scb/pcie@7d500000, using [bus 00-ff]
[ 1.148573] brcm-pcie fd500000.pcie: MEM 0x0600000000..0x063fffffff -> 0x00c0000000
[ 1.148661] brcm-pcie fd500000.pcie: IB MEM 0x0000000000..0x00bfffffff -> 0x0400000000
[ 1.206408] brcm-pcie fd500000.pcie: link up, 5.0 GT/s PCIe x1 (SSC)
[ 1.206806] brcm-pcie fd500000.pcie: PCI host bridge to bus 0000:00
[ 1.206827] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.206849] pci_bus 0000:00: root bus resource [mem 0x600000000-0x63fffffff] (bus address [0xc0000000-0xffffffff])
[ 1.206942] pci 0000:00:00.0: [14e4:2711] type 01 class 0x060400
[ 1.207192] pci 0000:00:00.0: PME# supported from D0 D3hot
[ 1.210684] PCI: bus0: Fast back to back transfers disabled
[ 1.211040] pci 0000:01:00.0: [1106:3483] type 00 class 0x0c0330
[ 1.211169] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00000fff 64bit]
[ 1.211610] pci 0000:01:00.0: PME# supported from D0 D3cold
[ 1.215098] PCI: bus1: Fast back to back transfers disabled
[ 1.215218] pci 0000:00:00.0: BAR 8: assigned [mem 0x600000000-0x6000fffff]
[ 1.215243] pci 0000:01:00.0: BAR 0: assigned [mem 0x600000000-0x600000fff 64bit]
[ 1.215328] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.215354] pci 0000:00:00.0: bridge window [mem 0x600000000-0x6000fffff]
[ 1.215771] pcieport 0000:00:00.0: enabling device (0140 -> 0142)
[ 1.216002] pcieport 0000:00:00.0: PME: Signaling with IRQ 62
[ 1.222701] Serial: 8250/16550 driver, 1 ports, IRQ sharing enabled
[ 1.225770] iproc-rng200 fe104000.rng: hwrng registered
[ 1.226080] vc-mem: phys_addr:0x00000000 mem_base=0x3ec00000 mem_size:0x40000000(1024 MiB)
[ 1.226961] gpiomem-bcm2835 fe200000.gpiomem: Initialised: Registers at 0xfe200000
[ 1.239817] brd: module loaded
[ 1.252533] loop: module loaded
[ 1.254400] Loading iSCSI transport class v2.0-870.
[ 1.257721] libphy: Fixed MDIO Bus: probed
[ 1.259432] bcmgenet fd580000.ethernet: GENET 5.0 EPHY: 0x0000
[ 1.274354] libphy: bcmgenet MII bus: probed
[ 1.354436] unimac-mdio unimac-mdio.-19: Broadcom UniMAC MDIO bus
[ 1.355665] usbcore: registered new interface driver r8152
[ 1.355736] usbcore: registered new interface driver lan78xx
[ 1.355814] usbcore: registered new interface driver smsc95xx
[ 1.357473] xhci_hcd 0000:01:00.0: enabling device (0140 -> 0142)
[ 1.357643] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 1.357680] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 1
[ 1.361183] xhci_hcd 0000:01:00.0: hcc params 0x002841eb hci version 0x100 quirks 0x0000060000000890
[ 1.362526] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 1.362545] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.362562] usb usb1: Product: xHCI Host Controller
[ 1.362579] usb usb1: Manufacturer: Linux 5.10.52-v7l+ xhci-hcd
[ 1.362597] usb usb1: SerialNumber: 0000:01:00.0
[ 1.363336] hub 1-0:1.0: USB hub found
[ 1.363437] hub 1-0:1.0: 1 port detected
[ 1.364122] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 1.364150] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[ 1.364176] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed
[ 1.364801] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
[ 1.364820] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.364837] usb usb2: Product: xHCI Host Controller
[ 1.364853] usb usb2: Manufacturer: Linux 5.10.52-v7l+ xhci-hcd
[ 1.364870] usb usb2: SerialNumber: 0000:01:00.0
[ 1.365617] hub 2-0:1.0: USB hub found
[ 1.365691] hub 2-0:1.0: 4 ports detected
[ 1.367390] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[ 1.367696] dwc_otg: FIQ enabled
[ 1.367711] dwc_otg: NAK holdoff enabled
[ 1.367726] dwc_otg: FIQ split-transaction FSM enabled
[ 1.367743] Module dwc_common_port init
[ 1.368241] usbcore: registered new interface driver uas
[ 1.368368] usbcore: registered new interface driver usb-storage
[ 1.368572] mousedev: PS/2 mouse device common for all mice
[ 1.370235] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer
[ 1.373747] sdhci: Secure Digital Host Controller Interface driver
[ 1.373763] sdhci: Copyright(c) Pierre Ossman
[ 1.374499] mmc-bcm2835 fe300000.mmcnr: could not get clk, deferring probe
[ 1.375086] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.379358] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.379695] hid: raw HID events driver (C) Jiri Kosina
[ 1.379923] usbcore: registered new interface driver usbhid
[ 1.379938] usbhid: USB HID core driver
[ 1.386977] Initializing XFRM netlink socket
[ 1.387022] NET: Registered protocol family 17
[ 1.387184] Key type dns_resolver registered
[ 1.387635] Registering SWP/SWPB emulation handler
[ 1.387809] registered taskstats version 1
[ 1.387838] Loading compiled-in X.509 certificates
[ 1.388730] Key type ._fscrypt registered
[ 1.388747] Key type .fscrypt registered
[ 1.388762] Key type fscrypt-provisioning registered
[ 1.400623] uart-pl011 fe201000.serial: there is not valid maps for state default
[ 1.400882] uart-pl011 fe201000.serial: cts_event_workaround enabled
[ 1.400976] fe201000.serial: ttyAMA0 at MMIO 0xfe201000 (irq = 36, base_baud = 0) is a PL011 rev2
[ 1.401173] printk: console [ttyAMA0] enabled
[ 1.410608] bcm2835-power bcm2835-power: Broadcom BCM2835 power domains driver
[ 1.411693] mmc-bcm2835 fe300000.mmcnr: mmc_debug:0 mmc_debug2:0
[ 1.411711] mmc-bcm2835 fe300000.mmcnr: DMA channel allocated
[ 1.441762] of_cfs_init
[ 1.442034] of_cfs_init: OK
[ 1.461393] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[ 1.463083] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 1.464820] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 1.467848] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[ 1.469538] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 1.477017] mmc0: SDHCI controller on fe340000.emmc2 [fe340000.emmc2] using ADMA
[ 1.477716] Waiting for root device PARTUUID=e0f7eb03-02...
[ 1.515465] random: fast init done
[ 1.552741] mmc1: new high speed SDIO card at address 0001
[ 1.585289] mmc0: new ultra high speed DDR50 SDXC card at address aaaa
[ 1.586287] mmcblk0: mmc0:aaaa SN64G 59.5 GiB
[ 1.588409] mmcblk0: p1 p2
[ 1.607299] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 1.607379] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 1.608138] devtmpfs: mounted
[ 1.617760] Freeing unused kernel memory: 2048K
[ 1.644317] usb 1-1: new high-speed USB device number 2 using xhci_hcd
[ 1.664620] Run /sbin/init as init process
[ 1.664635] with arguments:
[ 1.664650] /sbin/init
[ 1.664664] splash
[ 1.664678] with environment:
[ 1.664693] HOME=/
[ 1.664707] TERM=linux
[ 1.837139] usb 1-1: New USB device found, idVendor=2109, idProduct=3431, bcdDevice= 4.21
[ 1.837162] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 1.837180] usb 1-1: Product: USB2.0 Hub
[ 1.839445] hub 1-1:1.0: USB hub found
[ 1.839727] hub 1-1:1.0: 4 ports detected
[ 2.080917] systemd[1]: System time before build time, advancing clock.
[ 2.164345] usb 1-1.4: new full-speed USB device number 3 using xhci_hcd
[ 2.182504] NET: Registered protocol family 10
[ 2.183982] Segment Routing with IPv6
[ 2.247612] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[ 2.249205] systemd[1]: Detected architecture arm.
[ 2.301774] usb 1-1.4: New USB device found, idVendor=10c4, idProduct=8c07, bcdDevice= 1.01
[ 2.301796] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.301814] usb 1-1.4: Product: HB-RF-USB-2
[ 2.301832] usb 1-1.4: Manufacturer: Alexander Reinert
[ 2.301849] usb 1-1.4: SerialNumber: febd69380fc1e81190e168713b0549ec
[ 2.306013] systemd[1]: Set hostname to <raspberrypi>.
[ 2.505584] uart-pl011 fe201000.serial: no DMA platform data
[ 2.993155] systemd[1]: /lib/systemd/system/debmatic-lighttpd.service:15: PIDFile= references path below legacy directory /var/run/, updating /var/run/lighttpd-debmatic.pid → /run/lighttpd-debmatic.pid; please update the unit file accordingly.
[ 2.999263] systemd[1]: /lib/systemd/system/debmatic-hs485d.service:15: PIDFile= references path below legacy directory /var/run/, updating /var/run/hs485dLoader.pid → /run/hs485dLoader.pid; please update the unit file accordingly.
[ 3.084659] random: systemd: uninitialized urandom read (16 bytes read)
[ 3.096647] random: systemd: uninitialized urandom read (16 bytes read)
[ 3.097628] systemd[1]: Listening on fsck to fsckd communication Socket.
[ 3.097946] random: systemd: uninitialized urandom read (16 bytes read)
[ 3.100118] systemd[1]: Created slice User and Session Slice.
[ 3.101149] systemd[1]: Listening on Journal Audit Socket.
[ 3.101296] systemd[1]: Reached target Slices.
[ 3.102016] systemd[1]: Listening on Journal Socket (/dev/log).
[ 3.267697] i2c /dev entries driver
[ 3.818982] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 3.932878] systemd-journald[112]: Received request to flush runtime journal from PID 1
[ 4.600538] rpivid-mem feb00000.hevc-decoder: rpivid-hevcmem initialised: Registers at 0xfeb00000 length 0x00010000
[ 4.607618] rpivid-mem feb10000.rpivid-local-intc: rpivid-intcmem initialised: Registers at 0xfeb10000 length 0x00001000
[ 4.608935] rpivid-mem feb20000.h264-decoder: rpivid-h264mem initialised: Registers at 0xfeb20000 length 0x00010000
[ 4.610520] rpivid-mem feb30000.vp9-decoder: rpivid-vp9mem initialised: Registers at 0xfeb30000 length 0x00010000
[ 4.682194] mc: Linux media interface: v0.10
[ 4.682217] vc_sm_cma: module is from the staging directory, the quality is unknown, you have been warned.
[ 4.689792] bcm2835_vc_sm_cma_probe: Videocore shared memory driver
[ 4.689862] [vc_sm_connected_init]: start
[ 4.693288] [vc_sm_connected_init]: installed successfully
[ 4.714953] videodev: Linux video capture interface: v2.00
[ 4.715076] snd_bcm2835: module is from the staging directory, the quality is unknown, you have been warned.
[ 4.768667] bcm2835_audio bcm2835_audio: card created with 8 channels
[ 4.802646] bcm2835_mmal_vchiq: module is from the staging directory, the quality is unknown, you have been warned.
[ 4.806517] bcm2835_mmal_vchiq: module is from the staging directory, the quality is unknown, you have been warned.
[ 4.819381] bcm2835_v4l2: module is from the staging directory, the quality is unknown, you have been warned.
[ 4.820606] bcm2835_isp: module is from the staging directory, the quality is unknown, you have been warned.
[ 4.893466] bcm2835_codec: module is from the staging directory, the quality is unknown, you have been warned.
[ 4.924460] bcm2835-isp bcm2835-isp: Device node output[0] registered as /dev/video13
[ 4.926128] bcm2835-isp bcm2835-isp: Device node capture[0] registered as /dev/video14
[ 4.933635] bcm2835-isp bcm2835-isp: Device node capture[1] registered as /dev/video15
[ 4.935536] bcm2835-isp bcm2835-isp: Device node stats[2] registered as /dev/video16
[ 4.935611] bcm2835-isp bcm2835-isp: Register output node 0 with media controller
[ 4.935693] bcm2835-isp bcm2835-isp: Register capture node 1 with media controller
[ 4.935759] bcm2835-isp bcm2835-isp: Register capture node 2 with media controller
[ 4.935824] bcm2835-isp bcm2835-isp: Register capture node 3 with media controller
[ 4.973271] bcm2835-isp bcm2835-isp: Loaded V4L2 bcm2835-isp
[ 4.984458] bcm2835-codec bcm2835-codec: Device registered as /dev/video10
[ 4.984569] bcm2835-codec bcm2835-codec: Loaded V4L2 decode
[ 5.001031] bcm2835-codec bcm2835-codec: Device registered as /dev/video11
[ 5.001081] bcm2835-codec bcm2835-codec: Loaded V4L2 encode
[ 5.012352] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 5.012685] bcm2835-codec bcm2835-codec: Device registered as /dev/video12
[ 5.012733] bcm2835-codec bcm2835-codec: Loaded V4L2 isp
[ 5.144636] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 5.225136] brcmfmac: F1 signature read @0x18000000=0x15264345
[ 5.249256] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 5.251189] usbcore: registered new interface driver brcmfmac
[ 5.544361] [drm] Initialized v3d 1.0.0 20180419 for fec00000.v3d on minor 0
[ 5.552350] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 5.552482] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 5.573210] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Jan 4 2021 19:56:29 version 7.45.229 (617f1f5 CY) FWID 01-2dbd9d2e
[ 5.650559] [drm] No displays found. Consider forcing hotplug if HDMI is attached
[ 5.650687] vc4-drm gpu: bound fe600000.firmwarekms (ops vc4_fkms_ops [vc4])
[ 5.660960] [drm] Initialized vc4 0.0.0 20140616 for gpu on minor 1
[ 7.114629] Under-voltage detected! (0x00050000)
[ 7.287416] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 7.316746] br0: port 1(eth0) entered blocking state
[ 7.316774] br0: port 1(eth0) entered disabled state
[ 7.317185] device eth0 entered promiscuous mode
[ 7.335320] bcmgenet fd580000.ethernet: configuring instance for external RGMII (RX delay)
[ 7.337843] bcmgenet fd580000.ethernet eth0: Link is Down
[ 7.669120] random: crng init done
[ 7.669142] random: 7 urandom warning(s) missed due to ratelimiting
[ 8.384468] Adding 102396k swap on /var/swap. Priority:-2 extents:1 across:102396k SSFS
[ 9.194368] Voltage normalised (0x00000000)
[ 15.674531] bcmgenet fd580000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
[ 15.674596] br0: port 1(eth0) entered blocking state
[ 15.674614] br0: port 1(eth0) entered forwarding state
[ 15.674805] IPv6: ADDRCONF(NETDEV_CHANGE): br0: link becomes ready
[ 18.813355] broken atomic modeset userspace detected, disabling atomic
[ 19.495300] broken atomic modeset userspace detected, disabling atomic
[ 20.325914] broken atomic modeset userspace detected, disabling atomic
[ 20.922072] broken atomic modeset userspace detected, disabling atomic
[ 21.824994] broken atomic modeset userspace detected, disabling atomic
[ 22.435739] broken atomic modeset userspace detected, disabling atomic
[ 23.259501] broken atomic modeset userspace detected, disabling atomic
[ 23.865975] broken atomic modeset userspace detected, disabling atomic
[ 24.849582] broken atomic modeset userspace detected, disabling atomic
[ 25.458922] broken atomic modeset userspace detected, disabling atomic
[ 8764.703855] usb 1-1.4: USB disconnect, device number 3
[ 8768.228492] Under-voltage detected! (0x00050005)
[ 8768.688370] usb 1-1.4: new full-speed USB device number 4 using xhci_hcd
[ 8768.825772] usb 1-1.4: New USB device found, idVendor=10c4, idProduct=8c07, bcdDevice= 1.01
[ 8768.825794] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 8768.825813] usb 1-1.4: Product: HB-RF-USB-2
[ 8768.825830] usb 1-1.4: Manufacturer: Alexander Reinert
[ 8768.825848] usb 1-1.4: SerialNumber: febd69380fc1e81190e168713b0549ec
[ 8774.468539] Voltage normalised (0x00000000)

Torsten

deimos
Beiträge: 4574
Registriert: 20.06.2017, 10:38
Wohnort: Leimersheim
Hat sich bedankt: 88 Mal
Danksagung erhalten: 586 Mal
Kontaktdaten:

Re: Neue Platine HB-RF-USB-2

Beitrag von deimos » 30.07.2021, 15:05

Hi,

bitte mal einen Reboot machen.

Zusätzlich:

Code: Alles auswählen

[ 8768.228492] Under-voltage detected! (0x00050005)
Dein Netzteil scheint zu klein dimensioniert zu sein, das kann zu massiven Problemen mit USB Geräten führen.

Viele Grüße
Alex

torbar
Beiträge: 13
Registriert: 29.07.2021, 19:53
System: Alternative CCU (auf Basis OCCU)

Re: Neue Platine HB-RF-USB-2

Beitrag von torbar » 30.07.2021, 15:19

Hi,

ok, have das Netzteil getauscht, vorher war der PI4B am USB der Fritzbox dran ... dachte die liefert immer genug power....
hier das neue dmesg

pi@raspberrypi:~ $ dmesg
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.10.52-v7l+ (dom@buildbot) (arm-linux-gnueabihf-gcc-8 (Ubuntu/Linaro 8.4.0-3ubuntu1) 8.4.0, GNU ld (GNU Binutils for Ubuntu) 2.34) #1440 SMP Tue Jul 27 09:55:21 BST 2021
[ 0.000000] CPU: ARMv7 Processor [410fd083] revision 3 (ARMv7), cr=30c5383d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] OF: fdt: Machine model: Raspberry Pi 4 Model B Rev 1.2
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] Reserved memory: created CMA memory pool at 0x000000000ec00000, size 512 MiB
[ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000000000-0x000000002fffffff]
[ 0.000000] Normal empty
[ 0.000000] HighMem [mem 0x0000000030000000-0x00000000fbffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000003b3fffff]
[ 0.000000] node 0: [mem 0x0000000040000000-0x00000000fbffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000000fbffffff]
[ 0.000000] On node 0 totalpages: 1012736
[ 0.000000] DMA zone: 1728 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 196608 pages, LIFO batch:63
[ 0.000000] HighMem zone: 816128 pages, LIFO batch:63
[ 0.000000] percpu: Embedded 20 pages/cpu s50764 r8192 d22964 u81920
[ 0.000000] pcpu-alloc: s50764 r8192 d22964 u81920 alloc=20*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1011008
[ 0.000000] Kernel command line: coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 smsc95xx.macaddr=DC:A6:32:FB:71:0D vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000 console=ttyAMA0,115200 console=tty1 root=PARTUUID=e0f7eb03-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait quiet splash plymouth.ignore-serial-consoles
[ 0.000000] Kernel parameter elevator= does not have any effect anymore.
Please use sysfs to set IO scheduler for individual devices.
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] software IO TLB: mapped [mem 0x0000000008890000-0x000000000c890000] (64MB)
[ 0.000000] Memory: 3404140K/4050944K available (10240K kernel code, 1364K rwdata, 3188K rodata, 2048K init, 891K bss, 122516K reserved, 524288K cma-reserved, 3264512K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] ftrace: allocating 34303 entries in 67 pages
[ 0.000000] ftrace: allocated 67 pages with 3 groups
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Rude variant of Tasks RCU enabled.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] random: get_random_bytes called from start_kernel+0x3c8/0x59c with crng_init=0
[ 0.000009] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns
[ 0.000027] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns
[ 0.000087] bcm2835: system timer (irq = 25)
[ 0.000735] arch_timer: cp15 timer(s) running at 54.00MHz (phys).
[ 0.000752] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xc743ce346, max_idle_ns: 440795203123 ns
[ 0.000771] sched_clock: 56 bits at 54MHz, resolution 18ns, wraps every 4398046511102ns
[ 0.000785] Switching to timer-based delay loop, resolution 18ns
[ 0.001040] Console: colour dummy device 80x30
[ 0.001108] printk: console [tty1] enabled
[ 0.001166] Calibrating delay loop (skipped), value calculated using timer frequency.. 108.00 BogoMIPS (lpj=540000)
[ 0.001199] pid_max: default: 32768 minimum: 301
[ 0.001363] LSM: Security Framework initializing
[ 0.001548] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.001575] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.003024] cgroup: Disabling memory control group subsystem
[ 0.003256] CPU: Testing write buffer coherency: ok
[ 0.003715] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.004941] Setting up static identity map for 0x200000 - 0x20003c
[ 0.005142] rcu: Hierarchical SRCU implementation.
[ 0.006079] smp: Bringing up secondary CPUs ...
[ 0.007285] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.008649] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.009945] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.010111] smp: Brought up 1 node, 4 CPUs
[ 0.010133] SMP: Total of 4 processors activated (432.00 BogoMIPS).
[ 0.010148] CPU: All CPU(s) started in HYP mode.
[ 0.010162] CPU: Virtualization extensions available.
[ 0.011099] devtmpfs: initialized
[ 0.025462] VFP support v0.3: implementor 41 architecture 3 part 40 variant 8 rev 0
[ 0.025690] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.025720] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.038255] pinctrl core: initialized pinctrl subsystem
[ 0.039333] NET: Registered protocol family 16
[ 0.043310] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[ 0.044086] audit: initializing netlink subsys (disabled)
[ 0.044348] audit: type=2000 audit(0.040:1): state=initialized audit_enabled=0 res=1
[ 0.044923] thermal_sys: Registered thermal governor 'step_wise'
[ 0.045700] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.045717] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.046114] Serial: AMBA PL011 UART driver
[ 0.078125] bcm2835-mbox fe00b880.mailbox: mailbox enabled
[ 0.090844] raspberrypi-firmware soc:firmware: Attached to firmware from 2021-07-21T16:21:46, variant start
[ 0.100856] raspberrypi-firmware soc:firmware: Firmware hash is 6a796bb0062a6c75191c57cba1c13f9300076d02
[ 0.141830] Kprobes globally optimized
[ 0.146930] bcm2835-dma fe007000.dma: DMA legacy API manager, dmachans=0x1
[ 0.151141] vgaarb: loaded
[ 0.151595] SCSI subsystem initialized
[ 0.151808] usbcore: registered new interface driver usbfs
[ 0.151881] usbcore: registered new interface driver hub
[ 0.151954] usbcore: registered new device driver usb
[ 0.152289] usb_phy_generic phy: supply vcc not found, using dummy regulator
[ 0.154275] clocksource: Switched to clocksource arch_sys_counter
[ 1.112907] VFS: Disk quotas dquot_6.6.0
[ 1.113001] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.113161] FS-Cache: Loaded
[ 1.113381] CacheFiles: Loaded
[ 1.124300] NET: Registered protocol family 2
[ 1.124542] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 1.126000] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 1.126041] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 1.126105] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 1.126176] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.126331] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 1.126366] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 1.126630] NET: Registered protocol family 1
[ 1.127373] RPC: Registered named UNIX socket transport module.
[ 1.127390] RPC: Registered udp transport module.
[ 1.127405] RPC: Registered tcp transport module.
[ 1.127420] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.127443] PCI: CLS 0 bytes, default 64
[ 1.130438] Initialise system trusted keyrings
[ 1.130676] workingset: timestamp_bits=14 max_order=20 bucket_order=6
[ 1.139211] zbud: loaded
[ 1.141346] FS-Cache: Netfs 'nfs' registered for caching
[ 1.142135] NFS: Registering the id_resolver key type
[ 1.142175] Key type id_resolver registered
[ 1.142190] Key type id_legacy registered
[ 1.142334] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.142351] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 1.143401] Key type asymmetric registered
[ 1.143418] Asymmetric key parser 'x509' registered
[ 1.143614] bounce: pool size: 64 pages
[ 1.143658] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 1.143871] io scheduler mq-deadline registered
[ 1.143888] io scheduler kyber registered
[ 1.148381] brcm-pcie fd500000.pcie: host bridge /scb/pcie@7d500000 ranges:
[ 1.148413] brcm-pcie fd500000.pcie: No bus range found for /scb/pcie@7d500000, using [bus 00-ff]
[ 1.148494] brcm-pcie fd500000.pcie: MEM 0x0600000000..0x063fffffff -> 0x00c0000000
[ 1.148582] brcm-pcie fd500000.pcie: IB MEM 0x0000000000..0x00bfffffff -> 0x0400000000
[ 1.206416] brcm-pcie fd500000.pcie: link up, 5.0 GT/s PCIe x1 (SSC)
[ 1.206813] brcm-pcie fd500000.pcie: PCI host bridge to bus 0000:00
[ 1.206834] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.206855] pci_bus 0000:00: root bus resource [mem 0x600000000-0x63fffffff] (bus address [0xc0000000-0xffffffff])
[ 1.206949] pci 0000:00:00.0: [14e4:2711] type 01 class 0x060400
[ 1.207200] pci 0000:00:00.0: PME# supported from D0 D3hot
[ 1.210689] PCI: bus0: Fast back to back transfers disabled
[ 1.211074] pci 0000:01:00.0: [1106:3483] type 00 class 0x0c0330
[ 1.211203] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00000fff 64bit]
[ 1.211644] pci 0000:01:00.0: PME# supported from D0 D3cold
[ 1.215126] PCI: bus1: Fast back to back transfers disabled
[ 1.215227] pci 0000:00:00.0: BAR 8: assigned [mem 0x600000000-0x6000fffff]
[ 1.215252] pci 0000:01:00.0: BAR 0: assigned [mem 0x600000000-0x600000fff 64bit]
[ 1.215337] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.215364] pci 0000:00:00.0: bridge window [mem 0x600000000-0x6000fffff]
[ 1.215777] pcieport 0000:00:00.0: enabling device (0140 -> 0142)
[ 1.216009] pcieport 0000:00:00.0: PME: Signaling with IRQ 62
[ 1.222703] Serial: 8250/16550 driver, 1 ports, IRQ sharing enabled
[ 1.225779] iproc-rng200 fe104000.rng: hwrng registered
[ 1.226091] vc-mem: phys_addr:0x00000000 mem_base=0x3ec00000 mem_size:0x40000000(1024 MiB)
[ 1.226971] gpiomem-bcm2835 fe200000.gpiomem: Initialised: Registers at 0xfe200000
[ 1.239898] brd: module loaded
[ 1.252647] loop: module loaded
[ 1.254547] Loading iSCSI transport class v2.0-870.
[ 1.257856] libphy: Fixed MDIO Bus: probed
[ 1.259566] bcmgenet fd580000.ethernet: GENET 5.0 EPHY: 0x0000
[ 1.274360] libphy: bcmgenet MII bus: probed
[ 1.354481] unimac-mdio unimac-mdio.-19: Broadcom UniMAC MDIO bus
[ 1.355707] usbcore: registered new interface driver r8152
[ 1.355778] usbcore: registered new interface driver lan78xx
[ 1.355856] usbcore: registered new interface driver smsc95xx
[ 1.357520] xhci_hcd 0000:01:00.0: enabling device (0140 -> 0142)
[ 1.357691] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 1.357728] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 1
[ 1.361224] xhci_hcd 0000:01:00.0: hcc params 0x002841eb hci version 0x100 quirks 0x0000060000000890
[ 1.362566] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 1.362586] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.362603] usb usb1: Product: xHCI Host Controller
[ 1.362620] usb usb1: Manufacturer: Linux 5.10.52-v7l+ xhci-hcd
[ 1.362637] usb usb1: SerialNumber: 0000:01:00.0
[ 1.363379] hub 1-0:1.0: USB hub found
[ 1.363479] hub 1-0:1.0: 1 port detected
[ 1.364161] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 1.364189] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[ 1.364214] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed
[ 1.364800] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
[ 1.364819] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.364836] usb usb2: Product: xHCI Host Controller
[ 1.364853] usb usb2: Manufacturer: Linux 5.10.52-v7l+ xhci-hcd
[ 1.364869] usb usb2: SerialNumber: 0000:01:00.0
[ 1.365607] hub 2-0:1.0: USB hub found
[ 1.365679] hub 2-0:1.0: 4 ports detected
[ 1.367359] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[ 1.367665] dwc_otg: FIQ enabled
[ 1.367680] dwc_otg: NAK holdoff enabled
[ 1.367694] dwc_otg: FIQ split-transaction FSM enabled
[ 1.367712] Module dwc_common_port init
[ 1.368208] usbcore: registered new interface driver uas
[ 1.368334] usbcore: registered new interface driver usb-storage
[ 1.368534] mousedev: PS/2 mouse device common for all mice
[ 1.370189] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer
[ 1.373691] sdhci: Secure Digital Host Controller Interface driver
[ 1.373707] sdhci: Copyright(c) Pierre Ossman
[ 1.374508] mmc-bcm2835 fe300000.mmcnr: could not get clk, deferring probe
[ 1.375095] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.379369] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.379708] hid: raw HID events driver (C) Jiri Kosina
[ 1.379936] usbcore: registered new interface driver usbhid
[ 1.379950] usbhid: USB HID core driver
[ 1.386952] Initializing XFRM netlink socket
[ 1.386996] NET: Registered protocol family 17
[ 1.387123] Key type dns_resolver registered
[ 1.387573] Registering SWP/SWPB emulation handler
[ 1.387748] registered taskstats version 1
[ 1.387778] Loading compiled-in X.509 certificates
[ 1.388674] Key type ._fscrypt registered
[ 1.388691] Key type .fscrypt registered
[ 1.388706] Key type fscrypt-provisioning registered
[ 1.400588] uart-pl011 fe201000.serial: there is not valid maps for state default
[ 1.400845] uart-pl011 fe201000.serial: cts_event_workaround enabled
[ 1.400938] fe201000.serial: ttyAMA0 at MMIO 0xfe201000 (irq = 36, base_baud = 0) is a PL011 rev2
[ 1.401135] printk: console [ttyAMA0] enabled
[ 1.409564] bcm2835-power bcm2835-power: Broadcom BCM2835 power domains driver
[ 1.410649] mmc-bcm2835 fe300000.mmcnr: mmc_debug:0 mmc_debug2:0
[ 1.410666] mmc-bcm2835 fe300000.mmcnr: DMA channel allocated
[ 1.439149] of_cfs_init
[ 1.439420] of_cfs_init: OK
[ 1.458823] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[ 1.460518] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 1.462207] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 1.465233] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[ 1.466919] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 1.474372] mmc0: SDHCI controller on fe340000.emmc2 [fe340000.emmc2] using ADMA
[ 1.475865] Waiting for root device PARTUUID=e0f7eb03-02...
[ 1.507352] random: fast init done
[ 1.533583] mmc1: new high speed SDIO card at address 0001
[ 1.579762] mmc0: new ultra high speed DDR50 SDXC card at address aaaa
[ 1.580777] mmcblk0: mmc0:aaaa SN64G 59.5 GiB
[ 1.583132] mmcblk0: p1 p2
[ 1.601459] EXT4-fs (mmcblk0p2): INFO: recovery required on readonly filesystem
[ 1.601478] EXT4-fs (mmcblk0p2): write access will be enabled during recovery
[ 1.644368] usb 1-1: new high-speed USB device number 2 using xhci_hcd
[ 1.745948] EXT4-fs (mmcblk0p2): recovery complete
[ 1.747884] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 1.747982] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 1.748751] devtmpfs: mounted
[ 1.758412] Freeing unused kernel memory: 2048K
[ 1.758744] Run /sbin/init as init process
[ 1.758758] with arguments:
[ 1.758773] /sbin/init
[ 1.758787] splash
[ 1.758801] with environment:
[ 1.758815] HOME=/
[ 1.758829] TERM=linux
[ 1.826943] usb 1-1: New USB device found, idVendor=2109, idProduct=3431, bcdDevice= 4.21
[ 1.826965] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 1.826983] usb 1-1: Product: USB2.0 Hub
[ 1.829260] hub 1-1:1.0: USB hub found
[ 1.829542] hub 1-1:1.0: 4 ports detected
[ 2.154828] usb 1-1.4: new full-speed USB device number 3 using xhci_hcd
[ 2.170049] systemd[1]: System time before build time, advancing clock.
[ 2.271427] NET: Registered protocol family 10
[ 2.272899] Segment Routing with IPv6
[ 2.301722] usb 1-1.4: New USB device found, idVendor=10c4, idProduct=8c07, bcdDevice= 1.01
[ 2.301744] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.301762] usb 1-1.4: Product: HB-RF-USB-2
[ 2.301779] usb 1-1.4: Manufacturer: Alexander Reinert
[ 2.301796] usb 1-1.4: SerialNumber: febd69380fc1e81190e168713b0549ec
[ 2.334761] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[ 2.336483] systemd[1]: Detected architecture arm.
[ 2.375713] systemd[1]: Set hostname to <raspberrypi>.
[ 2.484938] uart-pl011 fe201000.serial: no DMA platform data
[ 3.078949] systemd[1]: /lib/systemd/system/debmatic-lighttpd.service:15: PIDFile= references path below legacy directory /var/run/, updating /var/run/lighttpd-debmatic.pid → /run/lighttpd-debmatic.pid; please update the unit file accordingly.
[ 3.085037] systemd[1]: /lib/systemd/system/debmatic-hs485d.service:15: PIDFile= references path below legacy directory /var/run/, updating /var/run/hs485dLoader.pid → /run/hs485dLoader.pid; please update the unit file accordingly.
[ 3.169057] random: systemd: uninitialized urandom read (16 bytes read)
[ 3.181591] random: systemd: uninitialized urandom read (16 bytes read)
[ 3.182220] systemd[1]: Listening on Journal Audit Socket.
[ 3.182577] random: systemd: uninitialized urandom read (16 bytes read)
[ 3.183235] systemd[1]: Listening on udev Control Socket.
[ 3.183671] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 3.184999] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 3.187364] systemd[1]: Created slice User and Session Slice.
[ 3.303745] i2c /dev entries driver
[ 3.890899] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 4.013182] systemd-journald[121]: Received request to flush runtime journal from PID 1
[ 4.603946] rpivid-mem feb00000.hevc-decoder: rpivid-hevcmem initialised: Registers at 0xfeb00000 length 0x00010000
[ 4.614830] rpivid-mem feb10000.rpivid-local-intc: rpivid-intcmem initialised: Registers at 0xfeb10000 length 0x00001000
[ 4.626954] rpivid-mem feb20000.h264-decoder: rpivid-h264mem initialised: Registers at 0xfeb20000 length 0x00010000
[ 4.631173] rpivid-mem feb30000.vp9-decoder: rpivid-vp9mem initialised: Registers at 0xfeb30000 length 0x00010000
[ 4.821679] snd_bcm2835: module is from the staging directory, the quality is unknown, you have been warned.
[ 4.822554] vc_sm_cma: module is from the staging directory, the quality is unknown, you have been warned.
[ 4.830830] bcm2835_vc_sm_cma_probe: Videocore shared memory driver
[ 4.830859] [vc_sm_connected_init]: start
[ 4.832465] mc: Linux media interface: v0.10
[ 4.860271] [vc_sm_connected_init]: installed successfully
[ 4.867785] videodev: Linux video capture interface: v2.00
[ 4.868248] bcm2835_audio bcm2835_audio: card created with 8 channels
[ 4.917425] bcm2835_mmal_vchiq: module is from the staging directory, the quality is unknown, you have been warned.
[ 4.928456] bcm2835_v4l2: module is from the staging directory, the quality is unknown, you have been warned.
[ 4.997775] bcm2835_codec: module is from the staging directory, the quality is unknown, you have been warned.
[ 4.998799] bcm2835_isp: module is from the staging directory, the quality is unknown, you have been warned.
[ 5.010641] bcm2835-codec bcm2835-codec: Device registered as /dev/video10
[ 5.010708] bcm2835-codec bcm2835-codec: Loaded V4L2 decode
[ 5.042555] bcm2835-codec bcm2835-codec: Device registered as /dev/video11
[ 5.042608] bcm2835-codec bcm2835-codec: Loaded V4L2 encode
[ 5.051053] bcm2835-codec bcm2835-codec: Device registered as /dev/video12
[ 5.051105] bcm2835-codec bcm2835-codec: Loaded V4L2 isp
[ 5.093941] bcm2835-isp bcm2835-isp: Device node output[0] registered as /dev/video13
[ 5.097596] bcm2835-isp bcm2835-isp: Device node capture[0] registered as /dev/video14
[ 5.098234] bcm2835-isp bcm2835-isp: Device node capture[1] registered as /dev/video15
[ 5.100089] bcm2835-isp bcm2835-isp: Device node stats[2] registered as /dev/video16
[ 5.100122] bcm2835-isp bcm2835-isp: Register output node 0 with media controller
[ 5.100147] bcm2835-isp bcm2835-isp: Register capture node 1 with media controller
[ 5.100170] bcm2835-isp bcm2835-isp: Register capture node 2 with media controller
[ 5.100197] bcm2835-isp bcm2835-isp: Register capture node 3 with media controller
[ 5.100493] bcm2835-isp bcm2835-isp: Loaded V4L2 bcm2835-isp
[ 5.111079] [drm] Initialized v3d 1.0.0 20180419 for fec00000.v3d on minor 0
[ 5.113859] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 5.269222] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 5.285465] [drm] No displays found. Consider forcing hotplug if HDMI is attached
[ 5.285598] vc4-drm gpu: bound fe600000.firmwarekms (ops vc4_fkms_ops [vc4])
[ 5.286064] [drm] Initialized vc4 0.0.0 20140616 for gpu on minor 1
[ 5.354631] brcmfmac: F1 signature read @0x18000000=0x15264345
[ 5.367009] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 5.368794] usbcore: registered new interface driver brcmfmac
[ 5.634635] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 5.634763] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 5.644103] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Jan 4 2021 19:56:29 version 7.45.229 (617f1f5 CY) FWID 01-2dbd9d2e
[ 6.874401] Under-voltage detected! (0x00050000)
[ 7.417815] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 7.438699] br0: port 1(eth0) entered blocking state
[ 7.438731] br0: port 1(eth0) entered disabled state
[ 7.439129] device eth0 entered promiscuous mode
[ 7.454132] bcmgenet fd580000.ethernet: configuring instance for external RGMII (RX delay)
[ 7.454766] bcmgenet fd580000.ethernet eth0: Link is Down
[ 7.945645] random: crng init done
[ 7.945667] random: 7 urandom warning(s) missed due to ratelimiting
[ 8.474321] Adding 102396k swap on /var/swap. Priority:-2 extents:1 across:102396k SSFS
[ 8.954365] Voltage normalised (0x00000000)
[ 15.754582] bcmgenet fd580000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
[ 15.754649] br0: port 1(eth0) entered blocking state
[ 15.754668] br0: port 1(eth0) entered forwarding state
[ 15.754849] IPv6: ADDRCONF(NETDEV_CHANGE): br0: link becomes ready
[ 18.856502] broken atomic modeset userspace detected, disabling atomic
[ 19.536620] broken atomic modeset userspace detected, disabling atomic
[ 20.601444] broken atomic modeset userspace detected, disabling atomic
[ 21.197237] broken atomic modeset userspace detected, disabling atomic
[ 22.237261] broken atomic modeset userspace detected, disabling atomic
[ 22.872208] broken atomic modeset userspace detected, disabling atomic
[ 23.947414] broken atomic modeset userspace detected, disabling atomic
[ 24.531860] broken atomic modeset userspace detected, disabling atomic
[ 25.571876] broken atomic modeset userspace detected, disabling atomic
[ 26.175083] broken atomic modeset userspace detected, disabling atomic
pi@raspberrypi:~ $

deimos
Beiträge: 4574
Registriert: 20.06.2017, 10:38
Wohnort: Leimersheim
Hat sich bedankt: 88 Mal
Danksagung erhalten: 586 Mal
Kontaktdaten:

Re: Neue Platine HB-RF-USB-2

Beitrag von deimos » 30.07.2021, 15:26

Hi,

die Fritzbox reicht da absolut nicht aus, aber du hast immer noch ein Undervoltage drin.

Zusätzlich hast du scheinbar die Kernel Module nicht korrekt installiert, was liefert

Code: Alles auswählen

sudo dpkg-reconfigure pivccu-modules-dkms
Viele Grüße
Alex

torbar
Beiträge: 13
Registriert: 29.07.2021, 19:53
System: Alternative CCU (auf Basis OCCU)

Re: Neue Platine HB-RF-USB-2

Beitrag von torbar » 30.07.2021, 15:32

Hi,

das ist jetzt ein schmales iphone Netzteil ... wennäs immernoch nicht reicht, probier ich mal ein ipad netzteil.

soll ich das ganze listing posten, oder einfach einen reboot machen, der nach der reconfiguration angefordert ist ?

Torsten

jp112sdl
Beiträge: 9553
Registriert: 20.11.2016, 20:01
Hat sich bedankt: 596 Mal
Danksagung erhalten: 1405 Mal
Kontaktdaten:

Re: Neue Platine HB-RF-USB-2

Beitrag von jp112sdl » 30.07.2021, 15:37

Eigentlich steht in den Tech Specs zum
torbar hat geschrieben:
30.07.2021, 15:19
PI4B
https://www.raspberrypi.org/products/ra ... fications/
drin, was benötigt wird.
5V DC via USB-C connector (minimum 3A*)
5V DC via GPIO header (minimum 3A*)
* A good quality 2.5A power supply can be used if downstream USB peripherals consume less than 500mA in total.
Und was
torbar hat geschrieben:
30.07.2021, 15:32
ein schmales iphone Netzteil
liefert, steht auf selbigem drauf

VG,
Jérôme ☕️

---
Support for my Homebrew-Devices: Download JP-HB-Devices Addon

PN sind deaktiviert!

deimos
Beiträge: 4574
Registriert: 20.06.2017, 10:38
Wohnort: Leimersheim
Hat sich bedankt: 88 Mal
Danksagung erhalten: 586 Mal
Kontaktdaten:

Re: Neue Platine HB-RF-USB-2

Beitrag von deimos » 30.07.2021, 15:42

Hi,
torbar hat geschrieben:
30.07.2021, 15:32
soll ich das ganze listing posten, oder einfach einen reboot machen, der nach der reconfiguration angefordert ist ?
Die Ausgabe von dem dpkg. Wenn kein Fehler kommt, dann reboot und die Ausgabe von debmatic-info. Wenn ein Fehler kommt, nichts außer weiter machen.

Viele Grüße
Alex

Antworten

Zurück zu „Hardwareentwicklung und Selbstbau von Aktoren und Sensoren“