Platine HB-RF-ETH: Funkmodul per Netzwerk anbinden

[MathiasZ]

Jetzt ist Schluß mit OT:
Gestern habe ich meine 2 bestellt.
Bin gespannt, wann die kommen.
Wenn dann Fragen offen sind, melde ich mich einfach.
Gruß,
Mathias

[t0mk]

Guten Abend,

ich habe bist jetzt eine HB-RF-ETH-Platine im Testbetrieb mit einem HM-MOD-RPI-PCB gehabt, lief ohne Probleme zusammen mit debmatic auf Raspbian. Ich wollte nun auf RPI-RF-MOD umsteigen und habe das Funkmodul ausgetauscht. Es wurde von der Platine erkannt, leuchtete aber rot, was ja hier schon öfters beschrieben wurde. Da meine debmatic auf einem alten Stand war, habe ich daraufhin erstmal das System komplett aktualisiert. Seitdem kriege ich die Platine nicht mehr ans Laufen. Sie bootet, das Webinterface ist erreichbar, aber die LED auf dem Funkmodul ist nach einem kurzen Aufleuchten beim Booten aus.

Code: Alles auswählen

sudo dpkg-reconfigure hb-rf-eth

liefert

Code: Alles auswählen

The HB-RF-ETH module with IP 192.168.178.199 will be used.

Code: Alles auswählen

ping 192.168.178.199

geht und liefert stabile 0,2-0,3 ms

Code: Alles auswählen

dmesg | grep hb-rf-eth

liefert aber immer wieder

Code: Alles auswählen

hb-rf-eth hb-rf-eth: Error sending packet, not connected

Ich habe sämtliche Pakete rekonfiguriert und neu installiert, ich habe eine saubere pivccu-Installation aufgesetzt, sowohl stable als auch testing, aber mit demselben Ergebnis. Auch die Platine auf Werkseinstellungen zurückgesetzt. Stromversorgung von PoE auf USB umgestellt. Am Ergebnis ändert sich nichts.

Ich vermute, dass das Problem irgendwo in meinem Netzwerk-Setup vergraben ist, aber wo soll ich anfangen zu suchen? Außer die Fritte neu zu starten ist mir bis jetzt nichts eingefallen.

[deimos]

Hi,

welche Hardware setzt du ein? Was liefert dmesg (komplett ungefiltert). Wie sieht dein Netzwerksetup aus?

Viele Grüße
Alex

[t0mk]

Guten Morgen,

mein Netzwerksetup sieht folgendermaßen aus:

- FritzBox 7390
-> Kabel -> 1GB/s Switch
-> Patch-Kabel -> Patch-Panel -> CAT7-Kabel -> Netzwerk-Dose -> Kabel -> 1GB/s Switch -> Kabel -> Raspberry Pi4 mit piVCCU
-> Patch-Kabel -> PoE-Injektor -> Patch-Kabel -> Patch-Panel -> CAT7-Kabel -> Netzwerk-Dose -> Kabel -> HB-RF-ETH mit RPI-RF-MOD

Wie gesagt, mit einem HM-MOD-RPI-PCB hat es so funktioniert, leider habe ich dieses Funkmodul gerade nicht zur Verfügung.

Das sagt dmesg:

Code: Alles auswählen

pi@raspberrypi:~ $ dmesg
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.4.79-v7l+ (dom@buildbot) (gcc version 8.4.0 (Ubuntu/Linaro 8.4.0-3ubuntu1)) #1373 SMP Mon Nov 23 13:27:40 GMT 2020
[    0.000000] CPU: ARMv7 Processor [410fd083] revision 3 (ARMv7), cr=30c5383d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] OF: fdt: Machine model: Raspberry Pi 4 Model B Rev 1.2
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] Reserved memory: created CMA memory pool at 0x000000001ec00000, size 256 MiB
[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[    0.000000] On node 0 totalpages: 1012736
[    0.000000]   DMA zone: 2304 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 196608 pages, LIFO batch:63
[    0.000000]   HighMem zone: 816128 pages, LIFO batch:63
[    0.000000] percpu: Embedded 20 pages/cpu s49804 r8192 d23924 u81920
[    0.000000] pcpu-alloc: s49804 r8192 d23924 u81920 alloc=20*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 1010432
[    0.000000] Kernel command line: coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 video=HDMI-A-1:1280x1024M@60 smsc95xx.macaddr=DC:A6:32:85:53:2E vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000  dwc_otg.lpm_enable=0 console=tty1 root=PARTUUID=1e00dd95-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] software IO TLB: mapped [mem 0x17cc0000-0x1bcc0000] (64MB)
[    0.000000] Memory: 3655596K/4050944K available (10240K kernel code, 739K rwdata, 2816K rodata, 2048K init, 854K bss, 133204K reserved, 262144K cma-reserved, 3264512K highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] ftrace: allocating 31111 entries in 61 pages
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] random: get_random_bytes called from start_kernel+0x344/0x518 with crng_init=0
[    0.000004] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns
[    0.000013] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns
[    0.000051] bcm2835: system timer (irq = 17)
[    0.000315] arch_timer: cp15 timer(s) running at 54.00MHz (phys).
[    0.000323] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xc743ce346, max_idle_ns: 440795203123 ns
[    0.000331] sched_clock: 56 bits at 54MHz, resolution 18ns, wraps every 4398046511102ns
[    0.000337] Switching to timer-based delay loop, resolution 18ns
[    0.000444] Console: colour dummy device 80x30
[    0.000648] printk: console [tty1] enabled
[    0.000678] Calibrating delay loop (skipped), value calculated using timer frequency.. 108.00 BogoMIPS (lpj=540000)
[    0.000695] pid_max: default: 32768 minimum: 301
[    0.000762] LSM: Security Framework initializing
[    0.000854] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.000871] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.001492] Disabling memory control group subsystem
[    0.001555] CPU: Testing write buffer coherency: ok
[    0.001801] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.002196] Setting up static identity map for 0x200000 - 0x20003c
[    0.002289] rcu: Hierarchical SRCU implementation.
[    0.002593] smp: Bringing up secondary CPUs ...
[    0.003159] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.003767] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.004340] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.004404] smp: Brought up 1 node, 4 CPUs
[    0.004434] SMP: Total of 4 processors activated (432.00 BogoMIPS).
[    0.004445] CPU: All CPU(s) started in HYP mode.
[    0.004455] CPU: Virtualization extensions available.
[    0.004846] devtmpfs: initialized
[    0.010729] VFP support v0.3: implementor 41 architecture 3 part 40 variant 8 rev 0
[    0.010874] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.010897] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.014419] pinctrl core: initialized pinctrl subsystem
[    0.014932] NET: Registered protocol family 16
[    0.016680] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[    0.016945] audit: initializing netlink subsys (disabled)
[    0.017064] audit: type=2000 audit(0.010:1): state=initialized audit_enabled=0 res=1
[    0.017531] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.017546] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.017749] Serial: AMBA PL011 UART driver
[    0.019255] bcm2835-mbox fe00b880.mailbox: mailbox enabled
[    0.040370] raspberrypi-firmware soc:firmware: Attached to firmware from 2020-11-30 22:12, variant start
[    0.050360] raspberrypi-firmware soc:firmware: Firmware hash is ab1181cc0cb6df52bfae3b1d3fef0ce7c325166c
[    0.078762] bcm2835-dma fe007000.dma: DMA legacy API manager, dmachans=0x1
[    0.080973] vgaarb: loaded
[    0.081188] SCSI subsystem initialized
[    0.081302] usbcore: registered new interface driver usbfs
[    0.081332] usbcore: registered new interface driver hub
[    0.081380] usbcore: registered new device driver usb
[    0.081535] usb_phy_generic phy: phy supply vcc not found, using dummy regulator
[    0.082342] clocksource: Switched to clocksource arch_sys_counter
[    0.388553] VFS: Disk quotas dquot_6.6.0
[    0.388616] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.388718] FS-Cache: Loaded
[    0.388835] CacheFiles: Loaded
[    0.389272] simple-framebuffer 3e6c7000.framebuffer: framebuffer at 0x3e6c7000, 0x500000 bytes, mapped to 0x(ptrval)
[    0.389290] simple-framebuffer 3e6c7000.framebuffer: format=a8r8g8b8, mode=1280x1024x32, linelength=5120
[    0.392213] Console: switching to colour frame buffer device 160x64
[    0.394889] simple-framebuffer 3e6c7000.framebuffer: fb0: simplefb registered!
[    0.399007] thermal_sys: Registered thermal governor 'step_wise'
[    0.399177] NET: Registered protocol family 2
[    0.399558] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.399607] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.399666] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.399723] TCP: Hash tables configured (established 8192 bind 8192)
[    0.399826] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.399875] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.400024] NET: Registered protocol family 1
[    0.400384] RPC: Registered named UNIX socket transport module.
[    0.400415] RPC: Registered udp transport module.
[    0.400440] RPC: Registered tcp transport module.
[    0.400465] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.400501] PCI: CLS 0 bytes, default 64
[    0.401346] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
[    0.402462] Initialise system trusted keyrings
[    0.402596] workingset: timestamp_bits=14 max_order=20 bucket_order=6
[    0.407153] FS-Cache: Netfs 'nfs' registered for caching
[    0.407510] NFS: Registering the id_resolver key type
[    0.407553] Key type id_resolver registered
[    0.407577] Key type id_legacy registered
[    0.407606] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.408147] Key type asymmetric registered
[    0.408173] Asymmetric key parser 'x509' registered
[    0.408279] bounce: pool size: 64 pages
[    0.408317] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    0.408451] io scheduler mq-deadline registered
[    0.408478] io scheduler kyber registered
[    0.411510] brcm-pcie fd500000.pcie: host bridge /scb/pcie@7d500000 ranges:
[    0.412796] brcm-pcie fd500000.pcie:   No bus range found for /scb/pcie@7d500000, using [bus 00-ff]
[    0.414077] brcm-pcie fd500000.pcie:      MEM 0x0600000000..0x0603ffffff -> 0x00f8000000
[    0.415349] brcm-pcie fd500000.pcie:   IB MEM 0x0000000000..0x00bfffffff -> 0x0000000000
[    0.474412] brcm-pcie fd500000.pcie: link up, 5 GT/s x1 (SSC)
[    0.475769] brcm-pcie fd500000.pcie: PCI host bridge to bus 0000:00
[    0.476991] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.478200] pci_bus 0000:00: root bus resource [mem 0x600000000-0x603ffffff] (bus address [0xf8000000-0xfbffffff])
[    0.479432] pci 0000:00:00.0: [14e4:2711] type 01 class 0x060400
[    0.480767] pci 0000:00:00.0: PME# supported from D0 D3hot
[    0.483381] PCI: bus0: Fast back to back transfers disabled
[    0.484718] pci 0000:01:00.0: [1106:3483] type 00 class 0x0c0330
[    0.486016] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00000fff 64bit]
[    0.487480] pci 0000:01:00.0: PME# supported from D0 D3cold
[    0.490089] PCI: bus1: Fast back to back transfers disabled
[    0.491319] pci 0000:00:00.0: BAR 8: assigned [mem 0x600000000-0x6000fffff]
[    0.492564] pci 0000:01:00.0: BAR 0: assigned [mem 0x600000000-0x600000fff 64bit]
[    0.493842] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.495053] pci 0000:00:00.0:   bridge window [mem 0x600000000-0x6000fffff]
[    0.496380] pcieport 0000:00:00.0: enabling device (0140 -> 0142)
[    0.497689] pcieport 0000:00:00.0: PME: Signaling with IRQ 57
[    0.499062] pcieport 0000:00:00.0: AER: enabled with IRQ 57
[    0.500407] pci 0000:01:00.0: enabling device (0140 -> 0142)
[    0.503710] Serial: 8250/16550 driver, 1 ports, IRQ sharing enabled
[    0.506282] iproc-rng200 fe104000.rng: hwrng registered
[    0.507629] vc-mem: phys_addr:0x00000000 mem_base=0x3ec00000 mem_size:0x40000000(1024 MiB)
[    0.509128] vc-sm: Videocore shared memory driver
[    0.510553] gpiomem-bcm2835 fe200000.gpiomem: Initialised: Registers at 0xfe200000
[    0.516889] brd: module loaded
[    0.523853] loop: module loaded
[    0.525716] Loading iSCSI transport class v2.0-870.
[    0.527850] libphy: Fixed MDIO Bus: probed
[    0.529280] bcmgenet fd580000.ethernet: failed to get enet clock
[    0.530445] bcmgenet fd580000.ethernet: GENET 5.0 EPHY: 0x0000
[    0.531608] bcmgenet fd580000.ethernet: failed to get enet-wol clock
[    0.532781] bcmgenet fd580000.ethernet: failed to get enet-eee clock
[    0.533913] bcmgenet: Skipping UMAC reset
[    0.552373] libphy: bcmgenet MII bus: probed
[    0.632395] unimac-mdio unimac-mdio.-19: Broadcom UniMAC MDIO bus
[    0.633985] usbcore: registered new interface driver r8152
[    0.635140] usbcore: registered new interface driver lan78xx
[    0.636285] usbcore: registered new interface driver smsc95xx
[    0.637654] xhci_hcd 0000:01:00.0: xHCI Host Controller
[    0.638787] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 1
[    0.641053] xhci_hcd 0000:01:00.0: hcc params 0x002841eb hci version 0x100 quirks 0x0000003000000890
[    0.642795] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04
[    0.643929] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.645067] usb usb1: Product: xHCI Host Controller
[    0.646179] usb usb1: Manufacturer: Linux 5.4.79-v7l+ xhci-hcd
[    0.647310] usb usb1: SerialNumber: 0000:01:00.0
[    0.648695] hub 1-0:1.0: USB hub found
[    0.649880] hub 1-0:1.0: 1 port detected
[    0.651269] xhci_hcd 0000:01:00.0: xHCI Host Controller
[    0.652416] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[    0.653553] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed
[    0.654925] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.04
[    0.656066] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.657185] usb usb2: Product: xHCI Host Controller
[    0.658305] usb usb2: Manufacturer: Linux 5.4.79-v7l+ xhci-hcd
[    0.659437] usb usb2: SerialNumber: 0000:01:00.0
[    0.660805] hub 2-0:1.0: USB hub found
[    0.661942] hub 2-0:1.0: 4 ports detected
[    0.663793] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[    0.665027] dwc_otg: FIQ enabled
[    0.665032] dwc_otg: NAK holdoff enabled
[    0.665038] dwc_otg: FIQ split-transaction FSM enabled
[    0.665045] Module dwc_common_port init
[    0.665262] usbcore: registered new interface driver uas
[    0.666416] usbcore: registered new interface driver usb-storage
[    0.667616] mousedev: PS/2 mouse device common for all mice
[    0.669566] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer
[    0.671617] sdhci: Secure Digital Host Controller Interface driver
[    0.672733] sdhci: Copyright(c) Pierre Ossman
[    0.674102] mmc-bcm2835 fe300000.mmcnr: could not get clk, deferring probe
[    0.675461] sdhci-pltfm: SDHCI platform and OF driver helper
[    0.678879] ledtrig-cpu: registered to indicate activity on CPUs
[    0.680103] hidraw: raw HID events driver (C) Jiri Kosina
[    0.681281] usbcore: registered new interface driver usbhid
[    0.682393] usbhid: USB HID core driver
[    0.683963] vchiq: vchiq_init_state: slot_zero = (ptrval)
[    0.686181] [vc_sm_connected_init]: start
[    0.692679] [vc_sm_connected_init]: end - returning 0
[    0.694706] Initializing XFRM netlink socket
[    0.695812] NET: Registered protocol family 17
[    0.696950] Key type dns_resolver registered
[    0.698200] Registering SWP/SWPB emulation handler
[    0.699454] registered taskstats version 1
[    0.700542] Loading compiled-in X.509 certificates
[    0.701834] Key type ._fscrypt registered
[    0.702928] Key type .fscrypt registered
[    0.712701] fe215040.serial: ttyS0 at MMIO 0x0 (irq = 30, base_baud = 62500000) is a 16550
[    0.714111] bcm2835-power bcm2835-power: Broadcom BCM2835 power domains driver
[    0.715610] mmc-bcm2835 fe300000.mmcnr: mmc_debug:0 mmc_debug2:0
[    0.716682] mmc-bcm2835 fe300000.mmcnr: DMA channel allocated
[    0.765175] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[    0.767781] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    0.770442] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    0.774718] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[    0.777290] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    0.782344] mmc0: SDHCI controller on fe340000.emmc2 [fe340000.emmc2] using ADMA
[    0.784658] of_cfs_init
[    0.785755] of_cfs_init: OK
[    0.787181] Waiting for root device PARTUUID=1e00dd95-02...
[    0.826795] random: fast init done
[    0.845072] mmc1: new high speed SDIO card at address 0001
[    0.891738] mmc0: new ultra high speed DDR50 SDHC card at address aaaa
[    0.893256] mmcblk0: mmc0:aaaa SC16G 14.8 GiB
[    0.896829]  mmcblk0: p1 p2
[    0.910248] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    0.911354] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[    0.913018] devtmpfs: mounted
[    0.917676] Freeing unused kernel memory: 2048K
[    0.952466] Run /sbin/init as init process
[    1.012379] usb 1-1: new high-speed USB device number 2 using xhci_hcd
[    1.194997] usb 1-1: New USB device found, idVendor=2109, idProduct=3431, bcdDevice= 4.21
[    1.196118] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    1.197367] usb 1-1: Product: USB2.0 Hub
[    1.199961] hub 1-1:1.0: USB hub found
[    1.201286] hub 1-1:1.0: 4 ports detected
[    1.312024] systemd[1]: System time before build time, advancing clock.
[    1.385898] NET: Registered protocol family 10
[    1.387626] Segment Routing with IPv6
[    1.409066] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[    1.411943] systemd[1]: Detected architecture arm.
[    1.466862] systemd[1]: Set hostname to <raspberrypi>.
[    1.532409] usb 1-1.3: new low-speed USB device number 3 using xhci_hcd
[    1.672367] usb 1-1.3: New USB device found, idVendor=03f0, idProduct=0c4a, bcdDevice= 7.02
[    1.673572] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    1.674741] usb 1-1.3: Product: HP USB 1000dpi Laser Mouse
[    1.675892] usb 1-1.3: Manufacturer: HP
[    1.685956] input: HP HP USB 1000dpi Laser Mouse as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.3/1-1.3:1.0/0003:03F0:0C4A.0001/input/input0
[    1.688593] hid-generic 0003:03F0:0C4A.0001: input,hidraw0: USB HID v2.00 Mouse [HP HP USB 1000dpi Laser Mouse] on usb-0000:01:00.0-1.3/input0
[    1.696014] input: HP HP USB 1000dpi Laser Mouse Consumer Control as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.3/1-1.3:1.1/0003:03F0:0C4A.0002/input/input1
[    1.762653] hid-generic 0003:03F0:0C4A.0002: input,hiddev96,hidraw1: USB HID v2.00 Device [HP HP USB 1000dpi Laser Mouse] on usb-0000:01:00.0-1.3/input1
[    1.851868] systemd[1]: /lib/systemd/system/pivccu.service:8: PIDFile= references path below legacy directory /var/run/, updating /var/run/pivccu3.pid → /run/pivccu3.pid; please update the unit file accordingly.
[    1.872369] usb 1-1.4: new low-speed USB device number 4 using xhci_hcd
[    1.909514] random: systemd: uninitialized urandom read (16 bytes read)
[    1.915791] random: systemd: uninitialized urandom read (16 bytes read)
[    1.917538] systemd[1]: Listening on udev Control Socket.
[    1.921131] random: systemd: uninitialized urandom read (16 bytes read)
[    1.922908] systemd[1]: Listening on Journal Audit Socket.
[    1.926376] systemd[1]: Listening on fsck to fsckd communication Socket.
[    1.930042] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    1.933788] systemd[1]: Listening on Journal Socket.
[    1.944312] systemd[1]: Starting Restore / save the current clock...
[    2.014550] usb 1-1.4: New USB device found, idVendor=03f0, idProduct=0024, bcdDevice= 3.00
[    2.016454] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.016460] usb 1-1.4: Product: HP Basic USB Keyboard
[    2.016466] usb 1-1.4: Manufacturer: CHICONY
[    2.036605] input: CHICONY HP Basic USB Keyboard as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.4/1-1.4:1.0/0003:03F0:0024.0003/input/input2
[    2.102918] hid-generic 0003:03F0:0024.0003: input,hidraw2: USB HID v1.10 Keyboard [CHICONY HP Basic USB Keyboard] on usb-0000:01:00.0-1.4/input0
[    2.341945] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[    2.397400] systemd-journald[112]: Received request to flush runtime journal from PID 1
[    2.695516] vc_sm_cma: module is from the staging directory, the quality is unknown, you have been warned.
[    2.696404] bcm2835_vc_sm_cma_probe: Videocore shared memory driver
[    2.696414] [vc_sm_connected_init]: start
[    2.699913] [vc_sm_connected_init]: installed successfully
[    2.715540] generic_raw_uart: loading out-of-tree module taints kernel.
[    2.721599] mc: Linux media interface: v0.10
[    2.743686] videodev: Linux video capture interface: v2.00
[    2.764092] snd_bcm2835: module is from the staging directory, the quality is unknown, you have been warned.
[    2.767733] bcm2835_audio bcm2835_audio: card created with 4 channels
[    2.770094] bcm2835_audio bcm2835_audio: card created with 4 channels
[    2.806361] bcm2835_mmal_vchiq: module is from the staging directory, the quality is unknown, you have been warned.
[    2.817935] bcm2835_mmal_vchiq: module is from the staging directory, the quality is unknown, you have been warned.
[    2.823479] bcm2835_v4l2: module is from the staging directory, the quality is unknown, you have been warned.
[    2.839143] bcm2835_isp: module is from the staging directory, the quality is unknown, you have been warned.
[    2.841463] bcm2835_codec: module is from the staging directory, the quality is unknown, you have been warned.
[    2.862052] bcm2835-isp bcm2835-isp: Device node output[0] registered as /dev/video13
[    2.862105] bcm2835-codec bcm2835-codec: Device registered as /dev/video10
[    2.862127] bcm2835-codec bcm2835-codec: Loaded V4L2 decode
[    2.863916] bcm2835-isp bcm2835-isp: Device node capture[0] registered as /dev/video14
[    2.867495] bcm2835-isp bcm2835-isp: Device node capture[1] registered as /dev/video15
[    2.869483] bcm2835-isp bcm2835-isp: Device node stats[2] registered as /dev/video16
[    2.869503] bcm2835-isp bcm2835-isp: Register output node 0 with media controller
[    2.869512] bcm2835-isp bcm2835-isp: Register capture node 1 with media controller
[    2.869521] bcm2835-isp bcm2835-isp: Register capture node 2 with media controller
[    2.869543] bcm2835-isp bcm2835-isp: Register capture node 3 with media controller
[    2.873183] bcm2835-isp bcm2835-isp: Loaded V4L2 bcm2835-isp
[    2.886196] bcm2835-codec bcm2835-codec: Device registered as /dev/video11
[    2.886218] bcm2835-codec bcm2835-codec: Loaded V4L2 encode
[    2.890513] bcm2835-codec bcm2835-codec: Device registered as /dev/video12
[    2.890539] bcm2835-codec bcm2835-codec: Loaded V4L2 isp
[    2.908396] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    2.945131] pl011_raw_uart fe201000.serial: Initialized pl011 device; mapbase=0xfe201000; irq=29; clockrate=48000001
[    2.982133] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    3.033447] brcmfmac: F1 signature read @0x18000000=0x15264345
[    3.036249] [drm] Initialized v3d 1.0.0 20180419 for fec00000.v3d on minor 0
[    3.041262] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[    3.041678] usbcore: registered new interface driver brcmfmac
[    3.062355] vc4-drm gpu: bound fe600000.firmwarekms (ops vc4_fkms_ops [vc4])
[    3.062574] checking generic (3e6c7000 500000) vs hw (0 ffffffffffffffff)
[    3.062583] fb0: switching to vc4drmfb from simple
[    3.062925] Console: switching to colour dummy device 80x30
[    3.063317] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    3.063323] [drm] No driver support for vblank timestamp query.
[    3.063328] [drm] Setting vblank_disable_immediate to false because get_vblank_timestamp == NULL
[    3.063649] [drm] Initialized vc4 0.0.0 20140616 for gpu on minor 1
[    3.081710] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43455-sdio.raspberrypi,4-model-b.txt failed with error -2
[    3.120338] rpivid-mem feb00000.hevc-decoder: rpivid-hevcmem initialised: Registers at 0xfeb00000 length 0x00010000
[    3.120593] rpivid-mem feb10000.rpivid-local-intc: rpivid-intcmem initialised: Registers at 0xfeb10000 length 0x00001000
[    3.120826] rpivid-mem feb20000.h264-decoder: rpivid-h264mem initialised: Registers at 0xfeb20000 length 0x00010000
[    3.121045] rpivid-mem feb30000.vp9-decoder: rpivid-vp9mem initialised: Registers at 0xfeb30000 length 0x00010000
[    3.202186] Console: switching to colour frame buffer device 160x64
[    3.210859] rtc-rx8130 1-0032: Unable to read registers #28..#30
[    3.210867] i2c i2c-1: probing for rx8130 failed
[    3.210887] rtc-rx8130: probe of 1-0032 failed with error -121
[    3.221454] vc4-drm gpu: fb0: vc4drmfb frame buffer device
[    3.294525] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[    3.304158] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Mar 23 2020 02:19:54 version 7.45.206 (r725000 CY) FWID 01-88ee44ea
[    4.037637] random: crng init done
[    4.037645] random: 7 urandom warning(s) missed due to ratelimiting
[    4.342608] Adding 102396k swap on /var/swap.  Priority:-2 extents:1 across:102396k SSFS
[    4.374585] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    4.384039] br0: port 1(eth0) entered blocking state
[    4.384047] br0: port 1(eth0) entered disabled state
[    4.384217] device eth0 entered promiscuous mode
[    4.389087] bcmgenet: Skipping UMAC reset
[    4.390859] bcmgenet fd580000.ethernet: configuring instance for external RGMII
[    4.391118] bcmgenet fd580000.ethernet eth0: Link is Down
[    9.592460] bcmgenet fd580000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[    9.592490] br0: port 1(eth0) entered blocking state
[    9.592497] br0: port 1(eth0) entered forwarding state
[    9.592581] IPv6: ADDRCONF(NETDEV_CHANGE): br0: link becomes ready
[   10.928476] Bluetooth: Core ver 2.22
[   10.928523] NET: Registered protocol family 31
[   10.928528] Bluetooth: HCI device and connection manager initialized
[   10.928542] Bluetooth: HCI socket layer initialized
[   10.928552] Bluetooth: L2CAP socket layer initialized
[   10.928565] Bluetooth: SCO socket layer initialized
[   10.937827] Bluetooth: HCI UART driver ver 2.3
[   10.937835] Bluetooth: HCI UART protocol H4 registered
[   10.937870] Bluetooth: HCI UART protocol Three-wire (H5) registered
[   10.938011] Bluetooth: HCI UART protocol Broadcom registered
[   11.112186] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   11.112193] Bluetooth: BNEP filters: protocol multicast
[   11.112205] Bluetooth: BNEP socket layer initialized
[   75.765303] raw-uart raw-uart: Reset radio module
[   93.997179] raw-uart raw-uart1: Reset radio module
[   93.997190] hb-rf-eth hb-rf-eth: Error sending packet, not connected
[   94.116803] hb-rf-eth hb-rf-eth: Error sending packet, not connected
[   94.163139] hb-rf-eth hb-rf-eth: Error sending packet, not connected
[   97.163257] hb-rf-eth hb-rf-eth: Error sending packet, not connected
[  100.163363] hb-rf-eth hb-rf-eth: Error sending packet, not connected
[  103.163480] hb-rf-eth hb-rf-eth: Error sending packet, not connected
[  103.552465] hb-rf-eth hb-rf-eth: Error sending packet, not connected

[deimos]

Hi,

wie sieht die Datei /etc/defaul/hb_rf_eth aus? Hat die HB-RF-ETH eine feste IP konfiguriert? Was steht auf der Statusseite der HB-RF-ETH? Wie sehen die Dateien /sys/class/hb-rf-eth/hb-rf-eth/is_connected und /sys/class/raw-uart/raw-uart1/device_type aus? Zu guter letzt: Was liefert pivccu-info?

Viele Grüße
Alex

[t0mk]

Guten Abend,

dann mal der Reihe nach, /etc/default/hb_rf_eth:

Code: Alles auswählen

B_RF_ETH_ADDRESS="192.168.178.199"

Hat die HB-RF-ETH eine feste IP konfiguriert?

Nein, aber sie bekommt per dhcp eine feste Adresse zugeordnet.

Was steht auf der Statusseite der HB-RF-ETH?

/sys/class/hb-rf-eth/hb-rf-eth/is_connected

Code: Alles auswählen

0

/sys/class/raw-uart/raw-uart1/device_type

Code: Alles auswählen

HB-RF-ETH@-

pivccu-info:

Code: Alles auswählen

piVCCU version: 3.55.5-52
Kernel modules: Available
Raw UART dev:   Available
Rasp.Pi UART:   Assigned to GPIO pins
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
/var/lib/piVCCU3/detect_hardware.inc: line 65: echo: write error: Invalid argument
HMRF Hardware:  unknown
 Board serial:  unknown
 Radio MAC:     unknown
HMIP Hardware:  unknown
 SGTIN:         unknown
 Radio MAC:     unknown
State:          STOPPED

[deimos]

Hi,

steht in der /etc/default/hb_rf_eth wirklich B_RF_ETH_ADDRESS, also ohne das H am Anfang? Dann dürfte das schon das Problem sein.

Viele Grüße
Alex

[t0mk]

Nein, sorry, war ein copy&paste Fehler, es steht schon

Code: Alles auswählen

HB_RF_ETH_ADDRESS="192.168.178.199"

drin

[deimos]

Hi,

ich habe das Problem gefunden. Kurzfristiger Workaround: Eine IP verwenden, welche weniger als 14 Zeichen hat, deine aktuelle hat 15.
Den richtigen Fix werde ich kurzfristig bereitstellen, aber ich kann nicht versprechen, dass ich das heute Abend noch schaffe.

Viele Grüße
Alex

[MathiasZ]

meine Platinen sind auch seit letzter Woche hier.
Bin gespannt, wann ich de Zeit finde, alles zusammen zu bauen