Hi,
[apology for using english - german answer is OK, but my writing would send you into uncontrollable laughter :-]
I've just updated my CCU to version 1.3 and something appears to have gone wrong - the display says BOOTING, but nothing happens. I've tried most things I can think of (waiting 10 minutes before powering up again, accessing via USB, pressing different key combinations, .... ) Nothing helps.
Is there a recovery mode that anyone knows about? Can I upload the firmware via tftp or equivalent?
In short: HELP!
Philip
Firmware problem
Moderator: Co-Administratoren
Firmware problem
Zuletzt geändert von Roland M. am 30.10.2018, 10:28, insgesamt 1-mal geändert.
Grund: Thema verschoben
Grund: Thema verschoben
Re: Firmware problem
Hi Philip,
I think you have exactly THIS problem -
http://homematic.monkeybits.de/componen ... -ccu-crash
hope that will help
Michael
I think you have exactly THIS problem -
http://homematic.monkeybits.de/componen ... -ccu-crash
hope that will help
Michael
Re: Firmware problem
Hi Michael,
Thanks - but that's not the problem: the firmware appears to have uploaded, but after installing, the CCU just displays 'BOOTING'. I suspect something has gone wrong during the upgrade on the machine. So I can't get into the CCU to disable anything... It's like I need a boot disk or something to get it going again...
Thanks for trying to help.
Ph.
Thanks - but that's not the problem: the firmware appears to have uploaded, but after installing, the CCU just displays 'BOOTING'. I suspect something has gone wrong during the upgrade on the machine. So I can't get into the CCU to disable anything... It's like I need a boot disk or something to get it going again...
Thanks for trying to help.
Ph.
Re: Firmware problem
Hi..
That's the first time I heart about this problem, so...sorry, I can't give any instructions how to solve this. You may contact eQ-3 directly...and: If you've got any answer to solve this problem, just post it here, so I can include this into my blog.
Thank you
Greets,
kaju
That's the first time I heart about this problem, so...sorry, I can't give any instructions how to solve this. You may contact eQ-3 directly...and: If you've got any answer to solve this problem, just post it here, so I can include this into my blog.
Thank you
Greets,
kaju
HomeMatic-INSIDE: http://www.homematic-inside.de
Re: Firmware problem
Hi,
Yep - tried the reset button. Just comes back as booting. It's as if it doesn't find an operating system... I know that certain routers can be 'unbricked' by sending a firmware image. This usually involves pressing buttons in a certain sequence or for a certain period. I was hoping this existed for the CCU as well. If it does, it doesn't appear to be documented anywhere...
I'll contact e3-q to see what they say. If anything useful (i.e. other than please send the unit to us), I'll make sure to post it here.
Thanks again,
Philip
Yep - tried the reset button. Just comes back as booting. It's as if it doesn't find an operating system... I know that certain routers can be 'unbricked' by sending a firmware image. This usually involves pressing buttons in a certain sequence or for a certain period. I was hoping this existed for the CCU as well. If it does, it doesn't appear to be documented anywhere...
I'll contact e3-q to see what they say. If anything useful (i.e. other than please send the unit to us), I'll make sure to post it here.
Thanks again,
Philip
Re: Firmware problem
I know the problem!
If I start the CCU with plugged power and Network it will always displayed "Booting".
If I start the CCU without power and Network it will work.
My be it will help you!
Sametime, my ccu RESTART after booting without power, so i wait untill the Vision Nr. are displayed e. g. "V. 1.3" and quickly I plugged the power in the ccu.
But be carefull, the batterys can lost the contact if you shack the CCU hard.
If I start the CCU with plugged power and Network it will always displayed "Booting".
If I start the CCU without power and Network it will work.
My be it will help you!
Sametime, my ccu RESTART after booting without power, so i wait untill the Vision Nr. are displayed e. g. "V. 1.3" and quickly I plugged the power in the ccu.
But be carefull, the batterys can lost the contact if you shack the CCU hard.