HB-RF-MOD externe Antenne

RouvenE · Beitrag von **RouvenE** » 09.07.2019, 20:39

Hallo,

Im Zuge des Umbaus des RPI-RF-MOD auf das HB-RF-USB verbaue ich ein Pigtail für eine externe Antenne.
In zwei verschiedenen Beiträgen habe ich 2 verschiedene Lötpunkte für die Masse des Pigtails gesehen...

Einmal wurde das Pigtail am Gehäuse des Chips und einmal direkt neben dem Anschluss für den Innenleiter verlötet.

Ist beides möglich oder sollte man besser zu einem davon tendieren ?

deimos · Beitrag von **deimos** » 09.07.2019, 20:55

Hi,

beides ist möglich, ich würde aber zur zweiten Variante tendieren: Um an das Blech zu lötrn, braucht man deutlich mehr Hitze, das kann schädlich für das Funkmodul sein. Zum anderen kann man die ungeschirmte Strecke deutlich kürzer machen, das sieht man auf den Bilder ja recht gut.

Viele Grüße
Alex

P.S. Was ist das HB-RF-MOD aus der Überschrift?

RouvenE · Beitrag von **RouvenE** » 10.07.2019, 23:20

Hi,

Habe die GPIO-Leiste des HB-RF-USB nun verlötet und das RPI-RF-MOD aufgesteckt.

Dabei habe ich die Chance genutzt und ein Pigtail anstatt der originalen Antenne am RPI-RF-MOD verlötet. Dabei hatte ich Probleme, den Außenleiter mit der Masse am RPI-RF-MOD stabil zu verlöten (neben dem Anschluss für den Innenleiter am Befestigungspunkt der originalen Antenne).
Deshalb versuchte ich, die Masse am großen silbernen Chipgehäuse zu verlöten. Das funktionierte anfangs gar nicht, erst mit deutlich mehr Hitze.

Letztlich habe ich alles verbaut und via USB angeschlossen und die Stromversorgung des RPi direkt hergestellt sowie die Versorgung über das Modul herausgezogen.

Die piVCCU3 fährt anstandslos hoch, meldet keine Fehler und scheint alles zu empfangen.

Gibt es einen Test, den ich laufen lassen zur Überprüfung der Funktionsfähigkeit aller Komponenten (GPIO alle sauber verbunden?)?

Und, wie würde ich es merken, wenn die externe Antenne nicht vollständig funktioniert? Befürchtung wäre unnötige Mehrstrahlung oder ablösende Masselötstelle bei heißem Modul ?

Vielleicht kann jemand dazu etwas sagen?

klassisch · Beitrag von **klassisch** » 11.07.2019, 05:22

RouvenE hat geschrieben: ↑
10.07.2019, 23:20
Die piVCCU3 fährt anstandslos hoch, meldet keine Fehler und scheint alles zu empfangen.

Das klingt doch gut! Glückwunsch!

RouvenE hat geschrieben: ↑
10.07.2019, 23:20
Gibt es einen Test, den ich laufen lassen zur Überprüfung der Funktionsfähigkeit aller Komponenten (GPIO alle sauber verbunden?)?

Falls Du Zweifel an den Lötstellen hast, hilft erst mal visuelle Inspektion der Lötstellen und ggf sanftes ziehen an den Kabeln. Das müssen die Lötstellen überstehen. Dann folgt die Langzeitbeobachtung im Betrieb. Aber das ergibt sich von selbst.
Ansonsten ist der erste Funktionstest schon bestanden. Alles wird empfangen. Du kannst jetzt noch einen transportablen Sender (z.B. Tür- Fenster-Kontakt) nehmen, und mit Deinem Smartphone über WebUI dessen Status beobachten. Dann immer wieder schaltend durch das Haus gehen und schauen, ob die Reichweite ausreicht. Mehr kannst Du ohne teure Messgeräte etc. nicht wirklich tun.

RouvenE hat geschrieben: ↑
10.07.2019, 23:20
Und, wie würde ich es merken, wenn die externe Antenne nicht vollständig funktioniert? Befürchtung wäre unnötige Mehrstrahlung oder ablösende Masselötstelle bei heißem Modul ?

Einfach das System locker - aber nicht übertrieben intensiv - beobachten. Am ehesten merkst Du das über die Nichtfunktion. Einige Geräte melden sich nicht oder funktionieren nicht mehr. Wenn das immer häufiger wird und sich ausbreitet oder schlagartig gar nichts mehr geht, dann mußt Du wieder ran. Oder wenn der DutyCycle hoch geht und hoch bleibt. Aber das wirst Du ohne Aufzeichnung nicht wirklich merken. Mehr kannst Du nicht wirklich tun.
Dabei das System aber nicht paranoid überwachen und nicht jede Einzelfehlermeldung zu ernst nehmen. Ich habe bei mir sehr gute Funkverhältnisse geschaffen. Dennoch gibt es immer wieder eine Servicemeldung eines (alten) Drehgriff Fensterkontakts, der aber tadellos funktioniert. Besonders die frühen HM-Geräte haben einige Bugs in der Firmware. Das ist eben dem Pioniercharakter des früheren Nischendaseins geschuldet. Manchmal muß man mit der Homematic und dem Funk geduldig und großherzig sein.

RouvenE · Beitrag von **RouvenE** » 11.07.2019, 14:21

Okay, ich werde vorsichtshalber von den Lötstellen Photos machen...

Ist es normal, dass das blaue Licht des RPI-RF-MOD irgendwann ausschaltet? Bisher hatte es immer geleuchtet, seit eben nicht mehr.
Die CCU beschwert sich aber auch nicht... die Frage ist, ob die CCU3 es merken würde oder der Raspberry den USB-Port zum HB-RF-USB ggf in einen Energiesparmodus versetzt hat.

deimos · Beitrag von **deimos** » 11.07.2019, 14:25

Hi,

RouvenE hat geschrieben: ↑
11.07.2019, 14:21
Ist es normal, dass das blaue Licht des RPI-RF-MOD irgendwann ausschaltet?

Nein, das ist nicht normal. Schau mal in der Ausgabe von dmesg ob da irgendwas mit Undervoltage steht.

Viele Grüße
Alex

RouvenE · Beitrag von **RouvenE** » 11.07.2019, 14:56

Vorhin war die blaue Lampe des externen Moduls ausgeschaltet, die CCU3 hat jedoch keine Fehler angezeigt.
Öffnete ich ein Fenster, hatte der Kontakt keine Veränderung gemeldet.

Jetzt gerade, nach dem Update auf 3.47.10 und einem Neustart leuchtet das Modul noch und auch die Sensor-Veränderung wird registriert.

Im Vergleich zum gestrigen Tage, an dem das Modul extern problemlos lief, habe ich ein ca. 10-12m langes RJ45-CAT7-Kabel als Verlängerung dazwischen geschaltet.

Ich hoffe, die Ausgabe von dmesg hilft... undervoltage kann ich nicht sehen, aber das Modul leuchtet auch noch - es hatte heute Morgen erst nach einiger Zeit scheinbar den Strom verloren bzw. leuchtete nicht mehr:

Code: Alles auswählen

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.19.42-v7+ (dom@dom-XPS-13-9370) (gcc version 4.9.3 (crosstool-NG crosstool-ng-1.22.0-88-g8460611)) #1219 SMP Tue May 14 21:20:58 BST 2019
[    0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c5383d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Raspberry Pi 3 Model B Plus Rev 1.3
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] cma: Reserved 8 MiB at 0x3ac00000
[    0.000000] On node 0 totalpages: 242688
[    0.000000]   Normal zone: 2133 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 242688 pages, LIFO batch:63
[    0.000000] random: get_random_bytes called from start_kernel+0xac/0x4b4 with crng_init=0
[    0.000000] percpu: Embedded 17 pages/cpu s39488 r8192 d21952 u69632
[    0.000000] pcpu-alloc: s39488 r8192 d21952 u69632 alloc=17*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 240555
[    0.000000] Kernel command line: coherent_pool=1M 8250.nr_uarts=1 bcm2708_fb.fbwidth=656 bcm2708_fb.fbheight=416 bcm2708_fb.fbswap=1 vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000  dwc_otg.lpm_enable=0 console=tty1 root=PARTUUID=17fc48fb-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 939084K/970752K available (8192K kernel code, 627K rwdata, 2164K rodata, 1024K init, 821K bss, 23476K reserved, 8192K cma-reserved)
[    0.000000] Virtual kernel memory layout:
                   vector  : 0xffff0000 - 0xffff1000   (   4 kB)
                   fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
                   vmalloc : 0xbb800000 - 0xff800000   (1088 MB)
                   lowmem  : 0x80000000 - 0xbb400000   ( 948 MB)
                   modules : 0x7f000000 - 0x80000000   (  16 MB)
                     .text : 0x(ptrval) - 0x(ptrval)   (9184 kB)
                     .init : 0x(ptrval) - 0x(ptrval)   (1024 kB)
                     .data : 0x(ptrval) - 0x(ptrval)   ( 628 kB)
                      .bss : 0x(ptrval) - 0x(ptrval)   ( 822 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] ftrace: allocating 26229 entries in 77 pages
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] arch_timer: cp15 timer(s) running at 19.20MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[    0.000003] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[    0.000010] Switching to timer-based delay loop, resolution 52ns
[    0.000142] Console: colour dummy device 80x30
[    0.000409] console [tty1] enabled
[    0.000442] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[    0.000462] pid_max: default: 32768 minimum: 301
[    0.000632] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000651] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.001132] CPU: Testing write buffer coherency: ok
[    0.001397] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.001722] Setting up static identity map for 0x100000 - 0x10003c
[    0.001802] rcu: Hierarchical SRCU implementation.
[    0.002193] smp: Bringing up secondary CPUs ...
[    0.002636] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.003092] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.003499] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.003552] smp: Brought up 1 node, 4 CPUs
[    0.003588] SMP: Total of 4 processors activated (153.60 BogoMIPS).
[    0.003598] CPU: All CPU(s) started in HYP mode.
[    0.003607] CPU: Virtualization extensions available.
[    0.004134] devtmpfs: initialized
[    0.009402] VFP support v0.3: implementor 41 architecture 3 part 40 variant 3 rev 4
[    0.009536] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.009559] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.009867] pinctrl core: initialized pinctrl subsystem
[    0.010343] NET: Registered protocol family 16
[    0.011831] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[    0.014384] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.014402] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.014524] Serial: AMBA PL011 UART driver
[    0.015546] bcm2835-mbox 3f00b880.mailbox: mailbox enabled
[    0.030940] bcm2835-dma 3f007000.dma: DMA legacy API manager at (ptrval), dmachans=0x1
[    0.031715] SCSI subsystem initialized
[    0.031827] usbcore: registered new interface driver usbfs
[    0.031860] usbcore: registered new interface driver hub
[    0.031911] usbcore: registered new device driver usb
[    0.050046] raspberrypi-firmware soc:firmware: Attached to firmware from 2019-03-27 15:45, variant start
[    0.060226] raspberrypi-firmware soc:firmware: Firmware hash is 2e98b31d18547962e564bdf88e57b3df7085c29b
[    0.070810] clocksource: Switched to clocksource arch_sys_counter
[    0.110395] VFS: Disk quotas dquot_6.6.0
[    0.110453] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.110569] FS-Cache: Loaded
[    0.110692] CacheFiles: Loaded
[    0.115070] NET: Registered protocol family 2
[    0.115467] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[    0.115496] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.115553] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.115641] TCP: Hash tables configured (established 8192 bind 8192)
[    0.115724] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.115755] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.115923] NET: Registered protocol family 1
[    0.116245] RPC: Registered named UNIX socket transport module.
[    0.116257] RPC: Registered udp transport module.
[    0.116266] RPC: Registered tcp transport module.
[    0.116275] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.117085] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 7 counters available
[    0.118535] Initialise system trusted keyrings
[    0.118643] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[    0.123036] FS-Cache: Netfs 'nfs' registered for caching
[    0.123319] NFS: Registering the id_resolver key type
[    0.123344] Key type id_resolver registered
[    0.123354] Key type id_legacy registered
[    0.123368] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.124443] Key type asymmetric registered
[    0.124457] Asymmetric key parser 'x509' registered
[    0.124489] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[    0.124580] io scheduler noop registered
[    0.124590] io scheduler deadline registered (default)
[    0.124682] io scheduler cfq registered
[    0.124692] io scheduler mq-deadline registered (default)
[    0.124702] io scheduler kyber registered
[    0.125992] BCM2708FB: allocated DMA memory 0xfad00000
[    0.126025] BCM2708FB: allocated DMA channel 0
[    0.131006] Console: switching to colour frame buffer device 82x26
[    0.134387] Serial: 8250/16550 driver, 1 ports, IRQ sharing enabled
[    0.136136] bcm2835-rng 3f104000.rng: hwrng registered
[    0.137185] vc-mem: phys_addr:0x00000000 mem_base=0x3ec00000 mem_size:0x40000000(1024 MiB)
[    0.139359] vc-sm: Videocore shared memory driver
[    0.140497] gpiomem-bcm2835 3f200000.gpiomem: Initialised: Registers at 0x3f200000
[    0.147335] brd: module loaded
[    0.153297] loop: module loaded
[    0.154336] Loading iSCSI transport class v2.0-870.
[    0.155752] libphy: Fixed MDIO Bus: probed
[    0.156801] usbcore: registered new interface driver lan78xx
[    0.157813] usbcore: registered new interface driver smsc95xx
[    0.158786] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[    0.187476] dwc_otg 3f980000.usb: base=(ptrval)
[    0.388569] Core Release: 2.80a
[    0.389553] Setting default values for core params
[    0.390566] Finished setting default values for core params
[    0.591723] Using Buffer DMA mode
[    0.592742] Periodic Transfer Interrupt Enhancement - disabled
[    0.593776] Multiprocessor Interrupt Enhancement - disabled
[    0.594800] OTG VER PARAM: 0, OTG VER FLAG: 0
[    0.595810] Dedicated Tx FIFOs mode
[    0.597016] WARN::dwc_otg_hcd_init:1045: FIQ DMA bounce buffers: virt = bad14000 dma = 0xfad14000 len=9024
[    0.598999] FIQ FSM acceleration enabled for :
               Non-periodic Split Transactions
               Periodic Split Transactions
               High-Speed Isochronous Endpoints
               Interrupt/Control Split Transaction hack enabled
[    0.603716] dwc_otg: Microframe scheduler enabled
[    0.603745] WARN::hcd_init_fiq:457: FIQ on core 1
[    0.604711] WARN::hcd_init_fiq:458: FIQ ASM at 8064b6dc length 36
[    0.605669] WARN::hcd_init_fiq:484: MPHI regs_base at f0006000
[    0.606667] dwc_otg 3f980000.usb: DWC OTG Controller
[    0.607648] dwc_otg 3f980000.usb: new USB bus registered, assigned bus number 1
[    0.608654] dwc_otg 3f980000.usb: irq 56, io mem 0x00000000
[    0.609664] Init: Port Power? op_state=1
[    0.610626] Init: Power Port (0)
[    0.611681] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[    0.613614] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.614656] usb usb1: Product: DWC OTG Controller
[    0.615675] usb usb1: Manufacturer: Linux 4.19.42-v7+ dwc_otg_hcd
[    0.616721] usb usb1: SerialNumber: 3f980000.usb
[    0.618031] hub 1-0:1.0: USB hub found
[    0.619016] hub 1-0:1.0: 1 port detected
[    0.620225] dwc_otg: FIQ enabled
[    0.620227] dwc_otg: NAK holdoff enabled
[    0.620230] dwc_otg: FIQ split-transaction FSM enabled
[    0.620235] Module dwc_common_port init
[    0.620375] usbcore: registered new interface driver usb-storage
[    0.621458] mousedev: PS/2 mouse device common for all mice
[    0.622880] bcm2835-wdt 3f100000.watchdog: Broadcom BCM2835 watchdog timer
[    0.624070] bcm2835-cpufreq: min=1400000 max=1400000
[    0.625320] sdhci: Secure Digital Host Controller Interface driver
[    0.626370] sdhci: Copyright(c) Pierre Ossman
[    0.627594] mmc-bcm2835 3f300000.mmc: could not get clk, deferring probe
[    0.628857] sdhost-bcm2835 3f202000.mmc: could not get clk, deferring probe
[    0.630009] sdhci-pltfm: SDHCI platform and OF driver helper
[    0.632238] ledtrig-cpu: registered to indicate activity on CPUs
[    0.633433] hidraw: raw HID events driver (C) Jiri Kosina
[    0.634652] usbcore: registered new interface driver usbhid
[    0.635796] usbhid: USB HID core driver
[    0.637296] vchiq: vchiq_init_state: slot_zero = (ptrval), is_master = 0
[    0.639415] [vc_sm_connected_init]: start
[    0.646410] [vc_sm_connected_init]: end - returning 0
[    0.647973] Initializing XFRM netlink socket
[    0.649032] NET: Registered protocol family 17
[    0.650128] Key type dns_resolver registered
[    0.651374] Registering SWP/SWPB emulation handler
[    0.652739] registered taskstats version 1
[    0.653787] Loading compiled-in X.509 certificates
[    0.658974] 3f215040.serial: ttyS0 at MMIO 0x0 (irq = 53, base_baud = 50000000) is a 16550
[    0.661626] mmc-bcm2835 3f300000.mmc: mmc_debug:0 mmc_debug2:0
[    0.662703] mmc-bcm2835 3f300000.mmc: DMA channel allocated
[    0.689400] sdhost: log_buf @ (ptrval) (fad13000)
[    0.726009] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[    0.728542] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    0.731017] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    0.734652] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[    0.738331] mmc0: sdhost-bcm2835 loaded - DMA enabled (>1)
[    0.739841] of_cfs_init
[    0.740748] of_cfs_init: OK
[    0.741893] Waiting for root device PARTUUID=17fc48fb-02...
[    0.797529] mmc0: host does not support reading read-only switch, assuming write-enable
[    0.801954] mmc0: new high speed SDHC card at address 0001
[    0.803493] mmcblk0: mmc0:0001 JB1RT 29.8 GiB
[    0.805796]  mmcblk0: p1 p2
[    0.815978] random: fast init done
[    0.822519] mmc1: new high speed SDIO card at address 0001
[    0.831051] Indeed it is in host mode hprt0 = 00021501
[    0.903863] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    0.905682] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[    0.907555] devtmpfs: mounted
[    0.911064] Freeing unused kernel memory: 1024K
[    0.912173] Run /sbin/init as init process
[    1.040846] usb 1-1: new high-speed USB device number 2 using dwc_otg
[    1.042007] Indeed it is in host mode hprt0 = 00001101
[    1.280995] usb 1-1: New USB device found, idVendor=0424, idProduct=2514, bcdDevice= b.b3
[    1.283240] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.284775] hub 1-1:1.0: USB hub found
[    1.286003] hub 1-1:1.0: 4 ports detected
[    1.287324] systemd[1]: System time before build time, advancing clock.
[    1.414348] NET: Registered protocol family 10
[    1.416171] Segment Routing with IPv6
[    1.441133] random: systemd: uninitialized urandom read (16 bytes read)
[    1.444075] random: systemd: uninitialized urandom read (16 bytes read)
[    1.447725] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)
[    1.451598] systemd[1]: Detected architecture arm.
[    1.464555] systemd[1]: Set hostname to <piVCCU>.
[    1.509677] random: systemd-cryptse: uninitialized urandom read (16 bytes read)
[    1.600845] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[    1.731005] usb 1-1.1: New USB device found, idVendor=0424, idProduct=2514, bcdDevice= b.b3
[    1.733287] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.734835] hub 1-1.1:1.0: USB hub found
[    1.736031] hub 1-1.1:1.0: 3 ports detected
[    1.867393] systemd[1]: Reached target Swap.
[    1.871718] systemd[1]: Created slice User and Session Slice.
[    1.875120] systemd[1]: Created slice System Slice.
[    1.878622] systemd[1]: Created slice system-getty.slice.
[    1.883313] systemd[1]: Mounting RPC Pipe File System...
[    1.886320] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    1.892968] systemd[1]: Mounting POSIX Message Queue File System...
[    2.050882] usb 1-1.1.2: new full-speed USB device number 4 using dwc_otg
[    2.209767] usb 1-1.1.2: New USB device found, idVendor=0403, idProduct=6f70, bcdDevice= 6.00
[    2.209776] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    2.209782] usb 1-1.1.2: Product: HB-RF-USB
[    2.209786] usb 1-1.1.2: Manufacturer: Alexander Reinert
[    2.209790] usb 1-1.1.2: SerialNumber: A93DI4TA
[    2.420328] EXT4-fs (mmcblk0p2): re-mounted. Opts: commit=30
[    2.458520] systemd-journald[107]: Received request to flush runtime journal from PID 1
[    2.510893] usb 1-1.1.1: new high-speed USB device number 5 using dwc_otg
[    2.641203] usb 1-1.1.1: New USB device found, idVendor=0424, idProduct=7800, bcdDevice= 3.00
[    2.641213] usb 1-1.1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    2.648987] generic_raw_uart: loading out-of-tree module taints kernel.
[    2.656240] usb 1-1.1.2: Found HB-RF-USB at usb-3f980000.usb-1.1.2
[    2.904962] lan78xx 1-1.1.1:1.0 (unnamed net_device) (uninitialized): No External EEPROM. Setting MAC Speed
[    2.905475] libphy: lan78xx-mdiobus: probed
[    2.912105] lan78xx 1-1.1.1:1.0 (unnamed net_device) (uninitialized): int urb period 64
[    2.942235] usbcore: registered new interface driver hb_rf_usb
[    3.031452] vc_sm_cma: module is from the staging directory, the quality is unknown, you have been warned.
[    3.032471] bcm2835_vc_sm_cma_probe: Videocore shared memory driver
[    3.032479] [vc_sm_connected_init]: start
[    3.032701] [vc_sm_connected_init]: installed successfully
[    3.072774] snd_bcm2835: module is from the staging directory, the quality is unknown, you have been warned.
[    3.077243] bcm2835_audio soc:audio: card created with 8 channels
[    3.077479] media: Linux media interface: v0.10
[    3.083572] rtc-rx8130 1-0032: Unable to read registers #28..#30
[    3.083582] i2c i2c-1: probing for rx8130 failed
[    3.083604] rtc-rx8130: probe of 1-0032 failed with error -121
[    3.103292] videodev: Linux video capture interface: v2.00
[    3.144977] bcm2835_mmal_vchiq: module is from the staging directory, the quality is unknown, you have been warned.
[    3.161191] pl011_raw_uart 3f201000.serial: Initialized pl011 device; mapbase=0x3f201000; irq=81; clockrate=47999625
[    3.183942] bcm2835_v4l2: module is from the staging directory, the quality is unknown, you have been warned.
[    3.183944] bcm2835_codec: module is from the staging directory, the quality is unknown, you have been warned.
[    3.257146] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    3.287472] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    3.324056] brcmfmac: F1 signature read @0x18000000=0x15264345
[    3.327806] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[    3.328160] usbcore: registered new interface driver brcmfmac
[    3.575182] random: crng init done
[    3.575198] random: 7 urandom warning(s) missed due to ratelimiting
[    3.584077] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[    3.594737] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Feb 27 2018 03:15:32 version 7.45.154 (r684107 CY) FWID 01-4fbe0b04
[    3.810392] bcm2835-codec bcm2835-codec: Device registered as /dev/video10
[    3.810403] bcm2835-codec bcm2835-codec: Loaded V4L2 decode
[    3.814290] bcm2835-codec bcm2835-codec: Device registered as /dev/video11
[    3.814301] bcm2835-codec bcm2835-codec: Loaded V4L2 encode
[    3.816952] bcm2835-codec bcm2835-codec: Device registered as /dev/video12
[    3.816961] bcm2835-codec bcm2835-codec: Loaded V4L2 isp
[    4.577177] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    4.593529] br0: port 1(eth0) entered blocking state
[    4.593539] br0: port 1(eth0) entered disabled state
[    4.593766] device eth0 entered promiscuous mode
[    4.605407] IPv6: ADDRCONF(NETDEV_UP): br0: link is not ready
[    6.651862] br0: port 1(eth0) entered blocking state
[    6.651868] br0: port 1(eth0) entered forwarding state
[    6.651969] IPv6: ADDRCONF(NETDEV_CHANGE): br0: link becomes ready
[    9.814665] raw-uart raw-uart: Reset radio module
[   10.443621] Bluetooth: Core ver 2.22
[   10.443683] NET: Registered protocol family 31
[   10.443686] Bluetooth: HCI device and connection manager initialized
[   10.443699] Bluetooth: HCI socket layer initialized
[   10.443706] Bluetooth: L2CAP socket layer initialized
[   10.443727] Bluetooth: SCO socket layer initialized
[   10.471385] Bluetooth: HCI UART driver ver 2.3
[   10.471393] Bluetooth: HCI UART protocol H4 registered
[   10.471457] Bluetooth: HCI UART protocol Three-wire (H5) registered
[   10.471581] Bluetooth: HCI UART protocol Broadcom registered
[   10.922251] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   10.922258] Bluetooth: BNEP filters: protocol multicast
[   10.922276] Bluetooth: BNEP socket layer initialized
[   25.815762] br0: port 2(vethpivccu) entered blocking state
[   25.815770] br0: port 2(vethpivccu) entered disabled state
[   25.816002] device vethpivccu entered promiscuous mode
[   25.816275] IPv6: ADDRCONF(NETDEV_UP): vethpivccu: link is not ready
[   25.898640] eth0: renamed from vethSBBIX5
[   25.971543] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   25.974225] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   25.974375] IPv6: ADDRCONF(NETDEV_CHANGE): vethpivccu: link becomes ready
[   25.974442] br0: port 2(vethpivccu) entered blocking state
[   25.974447] br0: port 2(vethpivccu) entered forwarding state
[   42.076763] eq3loop: created slave mmd_hmip
[   42.078265] eq3loop: created slave mmd_bidcos
[   44.166675] eq3loop: eq3loop_open_slave() mmd_bidcos
[   57.095488] eq3loop: eq3loop_open_slave() mmd_hmip
[   57.095686] eq3loop: eq3loop_close_slave() mmd_hmip
[   57.099185] eq3loop: eq3loop_open_slave() mmd_hmip
[   57.099353] eq3loop: eq3loop_close_slave() mmd_hmip
[   57.109361] eq3loop: eq3loop_open_slave() mmd_hmip
[  409.123000] eq3loop: eq3loop_close_slave() mmd_bidcos
[  409.468074] eq3loop: eq3loop_close_master() mmd_bidcos
[  409.468083] eq3loop: eq3loop_close_master() mmd_bidcos destroy device
[  409.468267] eq3loop: eq3loop_close_master() mmd_hmip
[  409.474980] eq3loop: eq3loop_close_slave() mmd_hmip
[  409.474988] eq3loop: eq3loop_close_slave() mmd_hmip destroy device
[  411.558652] br0: port 2(vethpivccu) entered disabled state
[  411.561291] device vethpivccu left promiscuous mode
[  411.561301] br0: port 2(vethpivccu) entered disabled state
[  510.458718] raw-uart raw-uart: Reset radio module
[  516.127555] br0: port 2(vethpivccu) entered blocking state
[  516.127567] br0: port 2(vethpivccu) entered disabled state
[  516.127840] device vethpivccu entered promiscuous mode
[  516.128180] IPv6: ADDRCONF(NETDEV_UP): vethpivccu: link is not ready
[  516.206126] eth0: renamed from vethJYP9LR
[  516.251174] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[  516.254179] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  516.254303] IPv6: ADDRCONF(NETDEV_CHANGE): vethpivccu: link becomes ready
[  516.254375] br0: port 2(vethpivccu) entered blocking state
[  516.254379] br0: port 2(vethpivccu) entered forwarding state
[  554.644135] eq3loop: created slave mmd_hmip
[  554.644379] eq3loop: created slave mmd_bidcos
[  556.738323] eq3loop: eq3loop_open_slave() mmd_bidcos
[  569.350723] eq3loop: eq3loop_open_slave() mmd_hmip
[  569.350901] eq3loop: eq3loop_close_slave() mmd_hmip
[  569.353811] eq3loop: eq3loop_open_slave() mmd_hmip
[  569.353958] eq3loop: eq3loop_close_slave() mmd_hmip
[  569.363034] eq3loop: eq3loop_open_slave() mmd_hmip

Aber, was ist zu tun, wenn undervoltage auftreten würde ? Einen Verstärker würde ich ungern zwischenschalten wollen. Ggf. schaltet der Pi doch einen USB schlafend ? Oder, und da wundere ich mich... vorher betrieb ich das RPI-RF-MOD auf den Raspberry GPIOs und versorgte das Modul mit Strom über das 3A-Netzteil von ELV. Jetzt, wo einzig der Raspberry via microUSB Strom direkt erhält, wird ja das schwächere Original-Netzteil mit 2.5A genutzt. Müsste man hier ggf. ein stärkeres Netzteil anschliessen ? Oder hätte das keinen Einfluss auf die USB-Ports ?

deimos · Beitrag von **deimos** » 11.07.2019, 15:08

Hi,

was meinst du damit, dass du 10-12m CAT7 Kabel zwischengehängt hast? Und meinst du nicht, dass es sinnvoll gewesen wäre, diese Info gleich zu nennen?

Das Kernel Modul verhindert, dass das Modul in einen Schlafmodus geschickt wird. Allerdings ist im Raspberry eine Logik drin, welche den USB Port bei einer Undervoltage hart abschaltet und genau deswegen solltest du da per dmesg im Kernel Log nachschauen. Das bringt natürlich nichts mehr, nachdem das durch einen Neustart gelöscht wurde.

Viele Grüße
Alex

RouvenE · Beitrag von **RouvenE** » 11.07.2019, 15:19

Okay, ich warte ab, bis der Fehler erneut auftritt und führe dmesg nochmals aus.

Ich hatte gestern das externe Modul direkt per USB am RPi dran, um die Funktionsfähigkeit zu testen.
Letztlich soll der RPi im anderen Stockwerk als das Modul mit externer Antenne stehen, weshalb ich nun im zweiten Schritt den empfohlenen USB-Extender und 10-12m CAT7-Kabel zwischen Modul und Raspberry habe.

Sollte jetzt der Moduls der Deaktivierung des Moduls erneut auftreten, würde ich ein 3A-Netzteil anschliessen wollen.

RouvenE · Beitrag von **RouvenE** » 12.07.2019, 10:24

Guten Morgen,

leider ist es wieder so weit... nun leuchtet das Modul permanent blau trotz zahlreicher Servicemeldungen der piVCCU3.
Versuche ich, Geräte über die WebGUI anzusprechen, reagieren diese nicht. Die CCU meldet nichts, führt dann aber die Geräte als gestörte Kommunikation auf. "Dmesg" sagt:

Code: Alles auswählen

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.19.42-v7+ (dom@dom-XPS-13-9370) (gcc version 4.9.3 (crosstool-NG crosstool-ng-1.22.0-88-g8460611)) #1219 SMP Tue May 14 21:20:58 BST 2019
[    0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c5383d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Raspberry Pi 3 Model B Plus Rev 1.3
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] cma: Reserved 8 MiB at 0x3ac00000
[    0.000000] On node 0 totalpages: 242688
[    0.000000]   Normal zone: 2133 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 242688 pages, LIFO batch:63
[    0.000000] random: get_random_bytes called from start_kernel+0xac/0x4b4 with crng_init=0
[    0.000000] percpu: Embedded 17 pages/cpu s39488 r8192 d21952 u69632
[    0.000000] pcpu-alloc: s39488 r8192 d21952 u69632 alloc=17*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 240555
[    0.000000] Kernel command line: coherent_pool=1M 8250.nr_uarts=1 bcm2708_fb.fbwidth=656 bcm2708_fb.fbheight=416 bcm2708_fb.fbswap=1 vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000  dwc_otg.lpm_enable=0 console=tty1 root=PARTUUID=17fc48fb-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 939084K/970752K available (8192K kernel code, 627K rwdata, 2164K rodata, 1024K init, 821K bss, 23476K reserved, 8192K cma-reserved)
[    0.000000] Virtual kernel memory layout:
                   vector  : 0xffff0000 - 0xffff1000   (   4 kB)
                   fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
                   vmalloc : 0xbb800000 - 0xff800000   (1088 MB)
                   lowmem  : 0x80000000 - 0xbb400000   ( 948 MB)
                   modules : 0x7f000000 - 0x80000000   (  16 MB)
                     .text : 0x(ptrval) - 0x(ptrval)   (9184 kB)
                     .init : 0x(ptrval) - 0x(ptrval)   (1024 kB)
                     .data : 0x(ptrval) - 0x(ptrval)   ( 628 kB)
                      .bss : 0x(ptrval) - 0x(ptrval)   ( 822 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] ftrace: allocating 26229 entries in 77 pages
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] arch_timer: cp15 timer(s) running at 19.20MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[    0.000003] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[    0.000010] Switching to timer-based delay loop, resolution 52ns
[    0.000142] Console: colour dummy device 80x30
[    0.000409] console [tty1] enabled
[    0.000442] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[    0.000462] pid_max: default: 32768 minimum: 301
[    0.000632] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000651] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.001132] CPU: Testing write buffer coherency: ok
[    0.001397] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.001722] Setting up static identity map for 0x100000 - 0x10003c
[    0.001802] rcu: Hierarchical SRCU implementation.
[    0.002193] smp: Bringing up secondary CPUs ...
[    0.002636] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.003092] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.003499] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.003552] smp: Brought up 1 node, 4 CPUs
[    0.003588] SMP: Total of 4 processors activated (153.60 BogoMIPS).
[    0.003598] CPU: All CPU(s) started in HYP mode.
[    0.003607] CPU: Virtualization extensions available.
[    0.004134] devtmpfs: initialized
[    0.009402] VFP support v0.3: implementor 41 architecture 3 part 40 variant 3 rev 4
[    0.009536] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.009559] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.009867] pinctrl core: initialized pinctrl subsystem
[    0.010343] NET: Registered protocol family 16
[    0.011831] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[    0.014384] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.014402] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.014524] Serial: AMBA PL011 UART driver
[    0.015546] bcm2835-mbox 3f00b880.mailbox: mailbox enabled
[    0.030940] bcm2835-dma 3f007000.dma: DMA legacy API manager at (ptrval), dmachans=0x1
[    0.031715] SCSI subsystem initialized
[    0.031827] usbcore: registered new interface driver usbfs
[    0.031860] usbcore: registered new interface driver hub
[    0.031911] usbcore: registered new device driver usb
[    0.050046] raspberrypi-firmware soc:firmware: Attached to firmware from 2019-03-27 15:45, variant start
[    0.060226] raspberrypi-firmware soc:firmware: Firmware hash is 2e98b31d18547962e564bdf88e57b3df7085c29b
[    0.070810] clocksource: Switched to clocksource arch_sys_counter
[    0.110395] VFS: Disk quotas dquot_6.6.0
[    0.110453] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.110569] FS-Cache: Loaded
[    0.110692] CacheFiles: Loaded
[    0.115070] NET: Registered protocol family 2
[    0.115467] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[    0.115496] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.115553] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.115641] TCP: Hash tables configured (established 8192 bind 8192)
[    0.115724] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.115755] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.115923] NET: Registered protocol family 1
[    0.116245] RPC: Registered named UNIX socket transport module.
[    0.116257] RPC: Registered udp transport module.
[    0.116266] RPC: Registered tcp transport module.
[    0.116275] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.117085] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 7 counters available
[    0.118535] Initialise system trusted keyrings
[    0.118643] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[    0.123036] FS-Cache: Netfs 'nfs' registered for caching
[    0.123319] NFS: Registering the id_resolver key type
[    0.123344] Key type id_resolver registered
[    0.123354] Key type id_legacy registered
[    0.123368] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.124443] Key type asymmetric registered
[    0.124457] Asymmetric key parser 'x509' registered
[    0.124489] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[    0.124580] io scheduler noop registered
[    0.124590] io scheduler deadline registered (default)
[    0.124682] io scheduler cfq registered
[    0.124692] io scheduler mq-deadline registered (default)
[    0.124702] io scheduler kyber registered
[    0.125992] BCM2708FB: allocated DMA memory 0xfad00000
[    0.126025] BCM2708FB: allocated DMA channel 0
[    0.131006] Console: switching to colour frame buffer device 82x26
[    0.134387] Serial: 8250/16550 driver, 1 ports, IRQ sharing enabled
[    0.136136] bcm2835-rng 3f104000.rng: hwrng registered
[    0.137185] vc-mem: phys_addr:0x00000000 mem_base=0x3ec00000 mem_size:0x40000000(1024 MiB)
[    0.139359] vc-sm: Videocore shared memory driver
[    0.140497] gpiomem-bcm2835 3f200000.gpiomem: Initialised: Registers at 0x3f200000
[    0.147335] brd: module loaded
[    0.153297] loop: module loaded
[    0.154336] Loading iSCSI transport class v2.0-870.
[    0.155752] libphy: Fixed MDIO Bus: probed
[    0.156801] usbcore: registered new interface driver lan78xx
[    0.157813] usbcore: registered new interface driver smsc95xx
[    0.158786] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[    0.187476] dwc_otg 3f980000.usb: base=(ptrval)
[    0.388569] Core Release: 2.80a
[    0.389553] Setting default values for core params
[    0.390566] Finished setting default values for core params
[    0.591723] Using Buffer DMA mode
[    0.592742] Periodic Transfer Interrupt Enhancement - disabled
[    0.593776] Multiprocessor Interrupt Enhancement - disabled
[    0.594800] OTG VER PARAM: 0, OTG VER FLAG: 0
[    0.595810] Dedicated Tx FIFOs mode
[    0.597016] WARN::dwc_otg_hcd_init:1045: FIQ DMA bounce buffers: virt = bad14000 dma = 0xfad14000 len=9024
[    0.598999] FIQ FSM acceleration enabled for :
               Non-periodic Split Transactions
               Periodic Split Transactions
               High-Speed Isochronous Endpoints
               Interrupt/Control Split Transaction hack enabled
[    0.603716] dwc_otg: Microframe scheduler enabled
[    0.603745] WARN::hcd_init_fiq:457: FIQ on core 1
[    0.604711] WARN::hcd_init_fiq:458: FIQ ASM at 8064b6dc length 36
[    0.605669] WARN::hcd_init_fiq:484: MPHI regs_base at f0006000
[    0.606667] dwc_otg 3f980000.usb: DWC OTG Controller
[    0.607648] dwc_otg 3f980000.usb: new USB bus registered, assigned bus number 1
[    0.608654] dwc_otg 3f980000.usb: irq 56, io mem 0x00000000
[    0.609664] Init: Port Power? op_state=1
[    0.610626] Init: Power Port (0)
[    0.611681] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[    0.613614] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.614656] usb usb1: Product: DWC OTG Controller
[    0.615675] usb usb1: Manufacturer: Linux 4.19.42-v7+ dwc_otg_hcd
[    0.616721] usb usb1: SerialNumber: 3f980000.usb
[    0.618031] hub 1-0:1.0: USB hub found
[    0.619016] hub 1-0:1.0: 1 port detected
[    0.620225] dwc_otg: FIQ enabled
[    0.620227] dwc_otg: NAK holdoff enabled
[    0.620230] dwc_otg: FIQ split-transaction FSM enabled
[    0.620235] Module dwc_common_port init
[    0.620375] usbcore: registered new interface driver usb-storage
[    0.621458] mousedev: PS/2 mouse device common for all mice
[    0.622880] bcm2835-wdt 3f100000.watchdog: Broadcom BCM2835 watchdog timer
[    0.624070] bcm2835-cpufreq: min=1400000 max=1400000
[    0.625320] sdhci: Secure Digital Host Controller Interface driver
[    0.626370] sdhci: Copyright(c) Pierre Ossman
[    0.627594] mmc-bcm2835 3f300000.mmc: could not get clk, deferring probe
[    0.628857] sdhost-bcm2835 3f202000.mmc: could not get clk, deferring probe
[    0.630009] sdhci-pltfm: SDHCI platform and OF driver helper
[    0.632238] ledtrig-cpu: registered to indicate activity on CPUs
[    0.633433] hidraw: raw HID events driver (C) Jiri Kosina
[    0.634652] usbcore: registered new interface driver usbhid
[    0.635796] usbhid: USB HID core driver
[    0.637296] vchiq: vchiq_init_state: slot_zero = (ptrval), is_master = 0
[    0.639415] [vc_sm_connected_init]: start
[    0.646410] [vc_sm_connected_init]: end - returning 0
[    0.647973] Initializing XFRM netlink socket
[    0.649032] NET: Registered protocol family 17
[    0.650128] Key type dns_resolver registered
[    0.651374] Registering SWP/SWPB emulation handler
[    0.652739] registered taskstats version 1
[    0.653787] Loading compiled-in X.509 certificates
[    0.658974] 3f215040.serial: ttyS0 at MMIO 0x0 (irq = 53, base_baud = 50000000) is a 16550
[    0.661626] mmc-bcm2835 3f300000.mmc: mmc_debug:0 mmc_debug2:0
[    0.662703] mmc-bcm2835 3f300000.mmc: DMA channel allocated
[    0.689400] sdhost: log_buf @ (ptrval) (fad13000)
[    0.726009] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[    0.728542] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    0.731017] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    0.734652] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[    0.738331] mmc0: sdhost-bcm2835 loaded - DMA enabled (>1)
[    0.739841] of_cfs_init
[    0.740748] of_cfs_init: OK
[    0.741893] Waiting for root device PARTUUID=17fc48fb-02...
[    0.797529] mmc0: host does not support reading read-only switch, assuming write-enable
[    0.801954] mmc0: new high speed SDHC card at address 0001
[    0.803493] mmcblk0: mmc0:0001 JB1RT 29.8 GiB
[    0.805796]  mmcblk0: p1 p2
[    0.815978] random: fast init done
[    0.822519] mmc1: new high speed SDIO card at address 0001
[    0.831051] Indeed it is in host mode hprt0 = 00021501
[    0.903863] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    0.905682] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[    0.907555] devtmpfs: mounted
[    0.911064] Freeing unused kernel memory: 1024K
[    0.912173] Run /sbin/init as init process
[    1.040846] usb 1-1: new high-speed USB device number 2 using dwc_otg
[    1.042007] Indeed it is in host mode hprt0 = 00001101
[    1.280995] usb 1-1: New USB device found, idVendor=0424, idProduct=2514, bcdDevice= b.b3
[    1.283240] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.284775] hub 1-1:1.0: USB hub found
[    1.286003] hub 1-1:1.0: 4 ports detected
[    1.287324] systemd[1]: System time before build time, advancing clock.
[    1.414348] NET: Registered protocol family 10
[    1.416171] Segment Routing with IPv6
[    1.441133] random: systemd: uninitialized urandom read (16 bytes read)
[    1.444075] random: systemd: uninitialized urandom read (16 bytes read)
[    1.447725] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)
[    1.451598] systemd[1]: Detected architecture arm.
[    1.464555] systemd[1]: Set hostname to <piVCCU>.
[    1.509677] random: systemd-cryptse: uninitialized urandom read (16 bytes read)
[    1.600845] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[    1.731005] usb 1-1.1: New USB device found, idVendor=0424, idProduct=2514, bcdDevice= b.b3
[    1.733287] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.734835] hub 1-1.1:1.0: USB hub found
[    1.736031] hub 1-1.1:1.0: 3 ports detected
[    1.867393] systemd[1]: Reached target Swap.
[    1.871718] systemd[1]: Created slice User and Session Slice.
[    1.875120] systemd[1]: Created slice System Slice.
[    1.878622] systemd[1]: Created slice system-getty.slice.
[    1.883313] systemd[1]: Mounting RPC Pipe File System...
[    1.886320] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    1.892968] systemd[1]: Mounting POSIX Message Queue File System...
[    2.050882] usb 1-1.1.2: new full-speed USB device number 4 using dwc_otg
[    2.209767] usb 1-1.1.2: New USB device found, idVendor=0403, idProduct=6f70, bcdDevice= 6.00
[    2.209776] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    2.209782] usb 1-1.1.2: Product: HB-RF-USB
[    2.209786] usb 1-1.1.2: Manufacturer: Alexander Reinert
[    2.209790] usb 1-1.1.2: SerialNumber: A93DI4TA
[    2.420328] EXT4-fs (mmcblk0p2): re-mounted. Opts: commit=30
[    2.458520] systemd-journald[107]: Received request to flush runtime journal from PID 1
[    2.510893] usb 1-1.1.1: new high-speed USB device number 5 using dwc_otg
[    2.641203] usb 1-1.1.1: New USB device found, idVendor=0424, idProduct=7800, bcdDevice= 3.00
[    2.641213] usb 1-1.1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    2.648987] generic_raw_uart: loading out-of-tree module taints kernel.
[    2.656240] usb 1-1.1.2: Found HB-RF-USB at usb-3f980000.usb-1.1.2
[    2.904962] lan78xx 1-1.1.1:1.0 (unnamed net_device) (uninitialized): No External EEPROM. Setting MAC Speed
[    2.905475] libphy: lan78xx-mdiobus: probed
[    2.912105] lan78xx 1-1.1.1:1.0 (unnamed net_device) (uninitialized): int urb period 64
[    2.942235] usbcore: registered new interface driver hb_rf_usb
[    3.031452] vc_sm_cma: module is from the staging directory, the quality is unknown, you have been warned.
[    3.032471] bcm2835_vc_sm_cma_probe: Videocore shared memory driver
[    3.032479] [vc_sm_connected_init]: start
[    3.032701] [vc_sm_connected_init]: installed successfully
[    3.072774] snd_bcm2835: module is from the staging directory, the quality is unknown, you have been warned.
[    3.077243] bcm2835_audio soc:audio: card created with 8 channels
[    3.077479] media: Linux media interface: v0.10
[    3.083572] rtc-rx8130 1-0032: Unable to read registers #28..#30
[    3.083582] i2c i2c-1: probing for rx8130 failed
[    3.083604] rtc-rx8130: probe of 1-0032 failed with error -121
[    3.103292] videodev: Linux video capture interface: v2.00
[    3.144977] bcm2835_mmal_vchiq: module is from the staging directory, the quality is unknown, you have been warned.
[    3.161191] pl011_raw_uart 3f201000.serial: Initialized pl011 device; mapbase=0x3f201000; irq=81; clockrate=47999625
[    3.183942] bcm2835_v4l2: module is from the staging directory, the quality is unknown, you have been warned.
[    3.183944] bcm2835_codec: module is from the staging directory, the quality is unknown, you have been warned.
[    3.257146] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    3.287472] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    3.324056] brcmfmac: F1 signature read @0x18000000=0x15264345
[    3.327806] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[    3.328160] usbcore: registered new interface driver brcmfmac
[    3.575182] random: crng init done
[    3.575198] random: 7 urandom warning(s) missed due to ratelimiting
[    3.584077] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[    3.594737] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Feb 27 2018 03:15:32 version 7.45.154 (r684107 CY) FWID 01-4fbe0b04
[    3.810392] bcm2835-codec bcm2835-codec: Device registered as /dev/video10
[    3.810403] bcm2835-codec bcm2835-codec: Loaded V4L2 decode
[    3.814290] bcm2835-codec bcm2835-codec: Device registered as /dev/video11
[    3.814301] bcm2835-codec bcm2835-codec: Loaded V4L2 encode
[    3.816952] bcm2835-codec bcm2835-codec: Device registered as /dev/video12
[    3.816961] bcm2835-codec bcm2835-codec: Loaded V4L2 isp
[    4.577177] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    4.593529] br0: port 1(eth0) entered blocking state
[    4.593539] br0: port 1(eth0) entered disabled state
[    4.593766] device eth0 entered promiscuous mode
[    4.605407] IPv6: ADDRCONF(NETDEV_UP): br0: link is not ready
[    6.651862] br0: port 1(eth0) entered blocking state
[    6.651868] br0: port 1(eth0) entered forwarding state
[    6.651969] IPv6: ADDRCONF(NETDEV_CHANGE): br0: link becomes ready
[    9.814665] raw-uart raw-uart: Reset radio module
[   10.443621] Bluetooth: Core ver 2.22
[   10.443683] NET: Registered protocol family 31
[   10.443686] Bluetooth: HCI device and connection manager initialized
[   10.443699] Bluetooth: HCI socket layer initialized
[   10.443706] Bluetooth: L2CAP socket layer initialized
[   10.443727] Bluetooth: SCO socket layer initialized
[   10.471385] Bluetooth: HCI UART driver ver 2.3
[   10.471393] Bluetooth: HCI UART protocol H4 registered
[   10.471457] Bluetooth: HCI UART protocol Three-wire (H5) registered
[   10.471581] Bluetooth: HCI UART protocol Broadcom registered
[   10.922251] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   10.922258] Bluetooth: BNEP filters: protocol multicast
[   10.922276] Bluetooth: BNEP socket layer initialized
[   25.815762] br0: port 2(vethpivccu) entered blocking state
[   25.815770] br0: port 2(vethpivccu) entered disabled state
[   25.816002] device vethpivccu entered promiscuous mode
[   25.816275] IPv6: ADDRCONF(NETDEV_UP): vethpivccu: link is not ready
[   25.898640] eth0: renamed from vethSBBIX5
[   25.971543] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   25.974225] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   25.974375] IPv6: ADDRCONF(NETDEV_CHANGE): vethpivccu: link becomes ready
[   25.974442] br0: port 2(vethpivccu) entered blocking state
[   25.974447] br0: port 2(vethpivccu) entered forwarding state
[   42.076763] eq3loop: created slave mmd_hmip
[   42.078265] eq3loop: created slave mmd_bidcos
[   44.166675] eq3loop: eq3loop_open_slave() mmd_bidcos
[   57.095488] eq3loop: eq3loop_open_slave() mmd_hmip
[   57.095686] eq3loop: eq3loop_close_slave() mmd_hmip
[   57.099185] eq3loop: eq3loop_open_slave() mmd_hmip
[   57.099353] eq3loop: eq3loop_close_slave() mmd_hmip
[   57.109361] eq3loop: eq3loop_open_slave() mmd_hmip
[  409.123000] eq3loop: eq3loop_close_slave() mmd_bidcos
[  409.468074] eq3loop: eq3loop_close_master() mmd_bidcos
[  409.468083] eq3loop: eq3loop_close_master() mmd_bidcos destroy device
[  409.468267] eq3loop: eq3loop_close_master() mmd_hmip
[  409.474980] eq3loop: eq3loop_close_slave() mmd_hmip
[  409.474988] eq3loop: eq3loop_close_slave() mmd_hmip destroy device
[  411.558652] br0: port 2(vethpivccu) entered disabled state
[  411.561291] device vethpivccu left promiscuous mode
[  411.561301] br0: port 2(vethpivccu) entered disabled state
[  510.458718] raw-uart raw-uart: Reset radio module
[  516.127555] br0: port 2(vethpivccu) entered blocking state
[  516.127567] br0: port 2(vethpivccu) entered disabled state
[  516.127840] device vethpivccu entered promiscuous mode
[  516.128180] IPv6: ADDRCONF(NETDEV_UP): vethpivccu: link is not ready
[  516.206126] eth0: renamed from vethJYP9LR
[  516.251174] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[  516.254179] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  516.254303] IPv6: ADDRCONF(NETDEV_CHANGE): vethpivccu: link becomes ready
[  516.254375] br0: port 2(vethpivccu) entered blocking state
[  516.254379] br0: port 2(vethpivccu) entered forwarding state
[  554.644135] eq3loop: created slave mmd_hmip
[  554.644379] eq3loop: created slave mmd_bidcos
[  556.738323] eq3loop: eq3loop_open_slave() mmd_bidcos
[  569.350723] eq3loop: eq3loop_open_slave() mmd_hmip
[  569.350901] eq3loop: eq3loop_close_slave() mmd_hmip
[  569.353811] eq3loop: eq3loop_open_slave() mmd_hmip
[  569.353958] eq3loop: eq3loop_close_slave() mmd_hmip
[  569.363034] eq3loop: eq3loop_open_slave() mmd_hmip

Und hier wundert es mich, dass scheinbar das USB1.1.-Modul (HB-RF-USB) zahlreiche Male gefunden wird.

HomeMatic-Forum / FHZ-Forum

HB-RF-MOD externe Antenne

HB-RF-MOD externe Antenne

Re: HB-RF-MOD externe Antenne

Re: HB-RF-MOD externe Antenne

Re: HB-RF-MOD externe Antenne

Re: HB-RF-MOD externe Antenne

Re: HB-RF-MOD externe Antenne

Re: HB-RF-MOD externe Antenne

Re: HB-RF-MOD externe Antenne

Re: HB-RF-MOD externe Antenne

Re: HB-RF-MOD externe Antenne