Hello, just starting with Homematic (IP) so there is still a lot to learn and read... So I tried finding answers to my following question but have not yet found it. So it would be great if someone had the answer or could point me to a topic where it is addressed (might even be in the German forum, reading is fine, writing/speaking less so)!
So my question:
The manual says that my HmIP-WTH-2 thermostats should be able to switch between manu, auto or a holiday or party mode. On my display I am not able to: it shows only "manu" or "auto".
My setup is with the CCU3 (with RaspberryMatic), thermostats switch a HmIP-MIOB. For my living room this controls a FALMOT-C12, others the radiators with HmIP-eTRV-2 or a electrical heater on a HmIP-PSM. All firmware latest.
So what do I miss?
Tia
Holiday and/or party mode: how?
Moderator: Co-Administratoren
- Baxxy
- Beiträge: 11027
- Registriert: 18.12.2018, 15:45
- System: Alternative CCU (auf Basis OCCU)
- Hat sich bedankt: 631 Mal
- Danksagung erhalten: 2284 Mal
Re: Holiday and/or party mode: how?
I think nothing. You can read about this here (in german). https://de.elv.com/forum/direktverknuep ... peckt-5802
Greets
Baxxy
Grüße... Baxxy
- Raspberry Pi 4 als Homematic-Zentrale - Tipps und Informationen
- Analysescript für genutzte Funk-Adressen, Funkmodul-Hardware und Zentralen Hardware
- NANO CUL 868MHz - Stick zum AskSin Analyzer XS umflashen (Anleitung für ArduinoIDE unter Windows)
- Firmware Updates für IP-Aktoren / Sensoren... Info's, Tipps und Sonstiges
- CCU funkt nicht - CarrierSense (CS) Probleme erkennen und lösen
Re: Holiday and/or party mode: how?
Ah, ok that indeed explains. Thanks Baxxy!Baxxy hat geschrieben: ↑25.01.2020, 13:57I think nothing. You can read about this here (in german). https://de.elv.com/forum/direktverknuep ... peckt-5802
Greets
Baxxy
So that would mean I need to create a program to get this kind of functionality and then control with a switch or maybe pocketControl, right?
- Baxxy
- Beiträge: 11027
- Registriert: 18.12.2018, 15:45
- System: Alternative CCU (auf Basis OCCU)
- Hat sich bedankt: 631 Mal
- Danksagung erhalten: 2284 Mal
Re: Holiday and/or party mode: how?
The easiest way is to use the CCU WebUI. Example: but with your ideas it should also go. Unfortunately i have less experience in that. But i think others can help.
Greets
Baxxy
Grüße... Baxxy
- Raspberry Pi 4 als Homematic-Zentrale - Tipps und Informationen
- Analysescript für genutzte Funk-Adressen, Funkmodul-Hardware und Zentralen Hardware
- NANO CUL 868MHz - Stick zum AskSin Analyzer XS umflashen (Anleitung für ArduinoIDE unter Windows)
- Firmware Updates für IP-Aktoren / Sensoren... Info's, Tipps und Sonstiges
- CCU funkt nicht - CarrierSense (CS) Probleme erkennen und lösen
-
- Beiträge: 13
- Registriert: 23.12.2020, 14:03
- System: CCU und Access Point
- Danksagung erhalten: 1 Mal
Re: Holiday and/or party mode: how?
How to set holiday mode for "whole house" (I've 5 groups/rooms configured)?
-
- Beiträge: 97
- Registriert: 01.11.2017, 18:28
- Wohnort: Estonia
- Hat sich bedankt: 3 Mal
- Danksagung erhalten: 9 Mal
Re: Holiday and/or party mode: how?
Check if we have related global variable (cannot do right now myself). If not, create and use its value for “whole house”, to address switches in operational mode, via simple program.
-
- Beiträge: 12436
- Registriert: 19.03.2014, 00:37
- System: in Planung
- Hat sich bedankt: 105 Mal
- Danksagung erhalten: 380 Mal
Re: Holiday and/or party mode: how?
No, my solution -> a program for start at time/date -> set groups (or, when only single thermostat) in manual mode with temp. 15°. Another program for end time/date -> set groups (or ...) in Automodus.
Regards
Bruno